Mobeye WaterGuard CM2300 User Manual
  1. Manuals
  2. Brands
  3. Mobeye Manuals
  4. Accessories
  5. WaterGuard CM2300
  6. User manual

Mobeye WaterGuard CM2300 User Manual

Water leakage sensor
Hide thumbs Also See for WaterGuard CM2300:
Table of Contents

Advertisement

Quick Links

Download this manual
USER MANUAL
®
Mobeye
WaterGuard
CM2300
Water leakage sensor
SW version 1.n

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WaterGuard CM2300 and is the answer not in the manual?

Questions and answers

Related Manuals for Mobeye WaterGuard CM2300

Summary of Contents for Mobeye WaterGuard CM2300

  • Page 1 USER MANUAL ® Mobeye WaterGuard CM2300 Water leakage sensor SW version 1.n...
  • Page 2 • Do not use in an environment where any inflammable gases, vapors or dust are present or could be present. ® • The repairs of the device may only be carried out by people, trained for Mobeye repair. • In case the device must be repaired, only original replacement components may be used. The use of ®...

  • Page 3: Table Of Contents

    CONTENT General description Getting started Place a SIM card Connect the water sensor to the unit Place the batteries Enter the program mode Program at least one telephone number Switching on/off Use of inputs and external power supply Using the input(s) Using external power Extended options Program mode...

  • Page 4: General Description

    - if external power supply is used- after a power failure. It is also possible to monitor the water level, in such a way that the Mobeye WaterGuard detects the absence of water.

  • Page 5: Getting Started

    2. GETTING STARTED To get started with the Mobeye WaterGuard at least the following steps need to be taken in following order: 1. Place SIM card (with PIN code 0000 or without PIN code) 2. Connect the water sensor to the unit 3.

  • Page 6: Program At Least One Telephone Number

    2.5 PROGRAM AT LEAST ONE TELEPHONE NUMBER The Mobeye WaterGuard is able to send messages up to 5 telephone numbers. The first telephone number belongs to the administrator. Technical messages (like “battery low”) are sent to the administrator only. Without the administrators’ phone number, the Mobeye WaterGuard cannot not function.

  • Page 7: Use Of Inputs And External Power Supply

    3.1 USING THE INPUT(S) It is possible to connect external sensors to the inputs. As a standard reaction after a triggered input, the Mobeye WaterGuard sends an SMS text message to the preset numbers and calls these numbers. Insert the 2 wires of an external sensor through the hole of the enclosure to the inside part and next in the two connectors of input 1 (press on the green pins for connecting the wires).

  • Page 8: Extended Options

    (or ‘on’ in case the first telephone number has been configured). The Mobeye WaterGuard returns to the program mode by pressing the on/off button during 5 seconds, until the LED starts flashing (or turns to ‘on’).

  • Page 9: Possible General Settings

    0031612345678). 4.4.2 Identification text It is possible to add a standard identification text (NAME) to all messages sent out by the Mobeye WaterGuard. The alarm messages are a combination of the name and the alarm text. A user defined identification has a length of maximum 20 characters. The default identification text is ‘Mobeye’.

  • Page 10: Input Delay Time

    SMS command interval test message: <CODE> TEST:xx 4.4.10 Power failure SMS message In case the Mobeye WaterGuard is powered externally and the power fails it sends an SMS text message to the administrator. The message is only sent in case the unit is armed. This message can be set to ‘OFF’.

  • Page 11: List Of Sms Commands For Configuration

    1111 TEL1:0612345678 Delete phone number1: 1111 DEL1 4.6 RESET OF SYSTEM To reset the Mobeye WaterGuard to its factory settings: Remove the batteries Press the outside button while entering the batteries. Keep it pressed for (about) another 5 seconds Release the button immediately after the LED starts to flash After a successful reset, the status LED on the keypad will blink green to indicate that the module is not configured.

  • Page 12: Request Overview Of The Settings And Status

    Before sending the request, make sure the unit is in the program mode (please refer to 4.1). 5.1 STATUS REQUEST The status of the Mobeye WaterGuard can be requested by sending an SMS with the content: <CODE> STATUS? Upon sending this request, the Mobeye WaterGuard returns the status to the originator of the request.

  • Page 13: Technical Messages And Status Feedback

    6. TECHNICAL MESSAGES AND STATUS FEEDBACK Technical messages are: In case of technical issues the administrator receives an SMS message. Possible messages are: Message Reason Low batteries, external power supply Power is available, batteries need to be replaced No external power supply, batteries OK No external power supply, batteries are capable to take over operation in low power mode Low batteries, no external power No external power supply, batteries need to be...
  • Page 14 Publisher. Reprinting, even in summary, is prohibited. This user manual meets the technical requirements at the moment of printing. Changes in technology and equipment are reserved. © Copyright 2012 by Mobeye, version CM2300EN120815...

Table of Contents