SIPOS AKTORIK 2SA7 Series Operation Instructions Manual

SIPOS AKTORIK 2SA7 Series Operation Instructions Manual

Electric actuators
Hide thumbs Also See for AKTORIK 2SA7 Series:

Advertisement

Operation instructions
Assembly, operation and commissioning
2SA7, 2SQ7
of
electric actuators
HiMod
Introduction
These operation instructions contain concise information required for assembly, operation and
commissioning. Extensive operation instructions for PROFITRON/HiMod are available on the
Internet: www.sipos.de ►
►Product documents ►Instruction manuals.
Contents
1
���������������������������������
1.1 Safety information ................................... 1
1.2 Transport and storage ............................. 2
1.3 Disposal and recycling ............................ 2
EU Declaration of conformity ........................... 2
1
2
���������������������� 2
2.1 Mount to valve/gear ................................. 2
2.2 Separate mounting .................................. 4
2.3 Remote control unit ................................. 4
2.4 Electrical connection ............................... 4
3
���������������������������������������������������
Should supplements be required for certain versions, applications, environmental conditions or
software functions of the actuator, they will be included within the scope of delivery.
Issue: 05.19
Subject to changes without notice!
PROFITRON
1
3.2 Indications of the LEDs ........................... 6
3.3 Status indication ...................................... 6
3.4 Display - position bar .............................. 6
4
����������������������������������������
4.1 User management ................................... 7
4.2 End position adjustment .......................... 8
5
5.1 General safety information .................... 10
5
5.2 Notes on inspection ............................... 10
5.3 Spare parts ............................................ 10
SIPOS Aktorik GmbH
1 General information
1�1 Safety information
General information
The devices referred to in this document are components of installations conceived for industrial
applications. They are designed in accordance with the recognized engineering rules.
All work involved in transport, assembly, installation, commissioning, maintenance and repair has
to be performed by qualified personnel.
Qualified personnel within the meaning of the relevant safety instructions of this documentation
are all persons authorized to perform the required tasks according to the standards of safety
technology and who may recognize and avoid potential hazards. They must be thoroughly familiar
with the warnings at the device and the safety instructions of these operation instructions.
Leakage currents
As standard, the leakage current of the actuators exceeds 3.5 mA. Therefore, fixed
installation in accordance with IEC 61800-5-1 is required.
Residual current circuit breaker or monitoring devices
Due to the integral frequency converter, a direct current within the protective ground-
ing conductor can be generated.
Should a residual current-operated protective (RCD) or monitoring (RCM) device be
used upstream the network, it must be of type B.
The distribution of this product is restricted according to IEC 61800-3.
and may cause radio interferences in domestic environments. In this case it may be necessary to
take additional measures.
The following is of particular importance:
The technical data and indications on permissible use (assembly, connection, environmental
and service conditions).
The general installation and safety guidelines as well as the local, plant-specific provisions and
requirements.
The proper use of tools and lifting and transport equipment.
The use of personal protective equipment, especially in high ambient temperatures and with
7
potential high actuator surface temperatures.
Prior to starting the assembly:
Make sure that the intended measures (possible operation of the valve, etc.) are not likely to
�������
10
cause any injuries to persons or to interfere with the equipment.
Heed the local ambient conditions, in particular the vibration load, which can be caused when
mounting an actuator to a vibrating valve.
1
Y070.485/EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AKTORIK 2SA7 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SIPOS AKTORIK 2SA7 Series

  • Page 1: Table Of Contents

    In this case it may be necessary to take additional measures. These operation instructions contain concise information required for assembly, operation and commissioning. Extensive operation instructions for PROFITRON/HiMod are available on the Internet: www.sipos.de ► ►Product documents ►Instruction manuals. The following is of particular importance: Contents ■...
  • Page 2: Transport And Storage

    If the paint was damaged during assembly, sorted according to materials, i.e.: electronic parts, different metals, plastics, greases and oils. it can be touched up with original paint supplied in small quantity units by SIPOS Aktorik. The following generally applies: ■...
  • Page 3 2�1�2 Output shaft type A Assembly procedure (see illustration): Assembly instruction 1. Place the actuator on the valve/gear, making sure it is properly centered. The stem nut is screwed onto the valve stem by turning the crank handle or the hand 2.
  • Page 4: Separate Mounting

    2�2 Separate mounting 2�4 Electrical connection If the ambient conditions such as extreme vibration, high temperature and/or if access is difficult, the Assembly procedure (refer to illustration on the electronics unit is to be mounted separately from the gear unit. The required assembly kit can be ordered next page): directly with the actuator or separately as accessory (2SX7300-.
  • Page 5: Operation

    3 Operation 3�1 Manual operation Fig�: Manual operation for 2SA7 Fig�: Manual operation for 2SQ7...
  • Page 6: 3.2 Indications Of The Leds

    3�2 Indications of the LEDs 3 Indication during operation: 3a = The value indicates how far the actuator has been operated to position OPEN. The position bar indicates the progress during operation (opening and closing the valve). 1 Depending on the actuator ordered, the colors of 3b = The symbol of the end position into which the actuator is currently being operating is flashing.
  • Page 7: Commissioning

    4 Commissioning 4�1 User management Many functions as well as parameterization can only be accessed using an access authorization (4-digit code). This prevents unauthorized persons from changing parameters inadvertently or advertently. Functions and parameters are grouped in user levels. Possible user levels are listed in the following table: Access to each user level, except for ‘Observer’...
  • Page 8: End Position Adjustment

    4�2 End position adjustment Adjust signaling gear ratio The complete commissioning procedure including 5. Approach and accept first end position (OPEN). parameterization is described in detail in the 6. Adjust central wheel position on signaling gear ”Operation instructions PROFITRON/HiMod“. (only for actuators with signaling gear). End position adjustment is divided into 8 main steps: 7.
  • Page 10: Mech. Position Indicator Adjustment

    4�3 Mechanical position indicator adjustment It is recommended that the services of the local SIPOS Aktorik service centers are utilized for this purpose, refer to . You may also send your requests www�sipos�de directly via e-mail to service@sipos�de 5�2�3 Lubricant assignment and quantity Actuator type 2SA7�1/2...

Table of Contents