1. Manuals
  2. Brands
  3. Patton Manuals
  4. Multiplexer
  5. FiberPlex TD-OADM Series
  6. User manual

Patton FiberPlex TD-OADM Series User Manual

Optical add/drop multiplexer
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
FiberPlex™TD-OADM Series
Optical Add/Drop Multiplexer
User Manual
Part Number: 07MTD-OADM-UM, Rev. B
Revised: October 24, 2018
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com

Advertisement

Table of Contents
loading

Related Manuals for Patton FiberPlex TD-OADM Series

Summary of Contents for Patton FiberPlex TD-OADM Series

  • Page 1 FiberPlex™TD-OADM Series Optical Add/Drop Multiplexer User Manual Sales Office: +1 (301) 975-1000 Part Number: 07MTD-OADM-UM, Rev. B Technical Support: +1 (301) 975-1007 Revised: October 24, 2018 E-mail: support@patton.com WWW: www.patton.com...
  • Page 2 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. CAUTION • Clean device with a dry cloth only. • Read these instructions. • Follow all instructions. IMPORTANT • Keep these instructions. 1.0 Introduction Figure 1.
  • Page 3 Figure 2. Typical application 1.1 Key features Primary applications: Metro area networks • Mobile fronthaul/backhaul • AV distribution • Large enterprise • Intra-SCIF (sensitive compartmented information facility) distribution • Wavelength: Full ITU-T G.694.2 spectrum grid support (1270 to 1610 nm) Isolation: East/West operation with 2 x TX/RX connections for center wavelength Power: Completely passive operation that requires no external power Extended Temperature: 23 to 149°F (-5 to 65°C)
  • Page 4 figure 4, a 1-channel TD-OADM supports a single channel in West and East directions. Each Drop port has a West and East port. Data transmitted by the West Drop port is split from the West fullband port, and data transmitted by East Drop port is split from the East fullband port.

  • Page 5: Installation

    1.4 Fullband Ports (West and East) Fullband ports (see figure 3 on page 4) transmit (TX) and receive (RX) the aggregated wavelengths connected to the Drop/Add ports. As shown in figure 4 on page 4, there are West and East fullband ports on the TD-OADM. The West fullband port and the East fullband port are internally connected so as to pass all wavelengths that are not in the TD-OADM’s specific wavelength.

  • Page 6: Customer And Technical Support

    (RX) is attached to the transmit side. Congratulations! The TD-OADM is installed. A.0 Customer and Technical Support Online support: www.patton.com E-mail support: support@patton.com—answered within 1 business day Telephone support: Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST • (1300 to 2200 UTC/GMT) Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 9:00 am to 5:30 pm...
  • Page 7 B.2 Fiber Type: SMF-28e bare fiber Connector: LC/UPC B.3 Channel Passband 6.5 nm ± B.4 Polarization dependent loss 0.2 dB B.5 Ripple in Passband B.6 Isolation West to east on signal: 30 dB Adjacent channel: 30 dB Non-adjacent channel: 40 dB B.7 Insertion Loss Add/drop (max): 1.3 dB...

  • Page 8: Compliance Information

    SN6 8AL, UK Copyright statement Copyright © 2018, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electron- ics assumes no liability for errors that may appear in this document. Trademarks statement Patton is a registered trademark of Patton Electronics Company in the United States and other countries.

Table of Contents