Advertisement
6. Inflate the ring with a manual air pump until the surface is firm to the touch. If there is any straining at the seams, the
product is over-inflated. If any seam begins to strain, immediately stop the inflation and release air to reduce the pressure
until signs of stress on the seam are gone. Do not over-inflate or use high pressure air compressor since it may result in
seam leaks. Important: the ambient temperatures of air and water have an effect on the internal pressure of the top ring. To maintain
a correct internal pressure, it is best to leave some room for expansion as the sun heats the air inside the ring. During very hot
weather, you must check to see whether it is necessary to release some air. This is to avoid any possible damage to the ring.
7. Fill the pool with no more than 1 inch (2.5cm) of water. Check to see whether the water is level. Important: if the water in the pool
flows to one side, the pool is not completely level. Setting up the pool on unleveled ground will cause the pool to tilt resulting in the
sidewall material to bulge and a potential collapse of the pool. If the pool is not completely level, you must drain the pool, level the
area and r e-fill the pool.
8. Smooth out the bottom liner wrinkles (from inside the pool) by pushing out where the pool floor and pool sides meet.
9. Fill the pool with water up to the bottom of the inflated ring which is the recommended fill line level. The pool liner walls will rise while
you are filling it.
Inspect the pool at the beginning of each use for holes, wear and tear and other damages.
Water can easily be contaminated. Change the water of paddling pool frequently
(particularly in hot weather) or when noticeably contaminated.
How to Drain Your Pool and Long Term Storage:
1.
Adults shall drain and store the pool. Check local regulations for specific directions regarding disposal of swimming pool water.
2.
Remove all accessories, toys, garden hose, etc from the pool.
3.
Open the drain valve cap (vary from models)
4.
Carefully open the inflation valve caps and/or exhaust valve caps to deflate the air chambers, and slowly push the sidewall inward
and down to speed up the drainage of the pool. Slowly lift one side of the pool to drain out the remaining standing water.
5.
Re-insert all valve caps afterwards for storage.
6.
Be sure pool and all parts are completely dry before folding, let it sit under the sun for an hour (see drawing 1). Sprinkle talcum
powder to prevent vinyl from sticking together and to absorb any water you may have missed.
7.
Create a square shape. Starting at one side, fold one-sixth of liner in on itself twice. Do the same on the opposite side
(see drawing 2.1 & 2.2).
8.
Once you have created two opposing folded sides, simply fold one over the other like closing a book (see drawing 3.1 & 3.2).
9.
Fold two long ends to the middle (see drawing 4).
10. Fold one over the other like closing a book and compact the liner (see drawing 5).
11.
Store the liner and accessories in a dry and cool storage location.
12. The original packing carton can be used for storage.
3.1
NOTE: All drawings for illustration purpose only. May not reflect actual product. Not to scale.
Repair patch:
A repair patch has been included with the product to repair small leak and holes. Refer to the instructions on the back of the repair patch.
For the following item number: 28102, 28103, 28104.
©2014 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten.
Made in China/Fabriqué en Chine/Hecho en China/Hergestellt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas
utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex
Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l'Union
Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
(235PO) WETSET SMALL EASY SET POOL SPANISH 6.5" X 9.75" 01/28/2014
WATER
LEVEL
POOL MAINTENANCE & DRAINAGE
Never use a damaged pool.
1
SAVE THESE INSTRUCTIONS
FILL LINE
Level
2.1
3.2
2.2
4
235
PO
5
Advertisement
