LG VX11000 Service Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Cell Phone
  5. VX11000
  6. Service manual

LG VX11000 Service Manual

Dual band cdma [pcs/cellular/gps] cdma mobile phone
Hide thumbs Also See for VX11000:
Table of Contents

Advertisement

Quick Links

Download this manual
Features of VX11000
1. Wave Type
● CELLULAR : G7W
● PCS: G7W
2. Frequency Scope
Transmit Frequency (MHz)
CELLULAR
824.82 ~ 848.19
3. Rated Output Power : CELLULAR = 0.316W
4. Output Conversion Method : This is possible by correcting the key board channel.
5. Voltage and Current Value of Termination Part Amplifier (Catalogue included)
MODE
CELLULAR
PCS
6. Functions of Major Semi-Conductors
Classification
MSM7500A-64T
Memory MCP
(KBN00300-A439)
RTR6500
7. Frequency Stability
● CELLULAR : ±0.5PPM
● PCS : ±0.1PPM
PCS
1850~1910
PCS = 0.316W
Part Name
ACPM-7353
ACPM-7353
Terminal operation control and digital signal processing
OneNAND Flash Memory (4G) + DDR-SDRAM (2G)
Storing of terminal operation program
Converts Rx and Tx RF signal to baseband signal
Receive Frequency (MHz)
CELLULAR
869.82~893.19
Voltage
Current
4.2V
400mA
4.2V
470mA
Function
PCS
GPS
1930~1990
1575.42
Power
0.316W
0.316W

Advertisement

Table of Contents
loading

Related Manuals for LG VX11000

Summary of Contents for LG VX11000

  • Page 1 Features of VX11000 1. Wave Type ● CELLULAR : G7W ● PCS: G7W 2. Frequency Scope Transmit Frequency (MHz) Receive Frequency (MHz) CELLULAR CELLULAR 824.82 ~ 848.19 1850~1910 869.82~893.19 1930~1990 1575.42 3. Rated Output Power : CELLULAR = 0.316W PCS = 0.316W 4.
  • Page 2 VX11000 CDMA Mobile Subscriber Unit VX11000 SERVICE MANUAL SERVICE MANUAL DUAL BAND CDMA [PCS/Cellular/GPS] CDMA MOBILE PHONE LG Electronics Inc. - 1/143-...
  • Page 4 Cellular uses 800MHz and PCS uses 1.9GHz. The VX11000 support GPS Mode, we usually call it tri-band phone. Also, VX11000 works on Advanced Mobile Phone Service (S-GPS). We call it dual- mode phone. If one of the Cellular, PCS base stations is located nearby, Call fail rate of triple-mode phone is less than dual-mode phone or single-mode phone.

  • Page 5: Cdma Abstract

    At this time, the spectrums of other signals that have different codes are not recovered into its original state, and appears as the self-interference of the system. LG Electronics Inc. - 4/143-...

  • Page 6: Features And Advantages Of Cdma Mobile Phone

    1.25msec (800 times per second). By doing so, the gain tolerance and the different radio propagation loss on the forward/backward link are complemented. LG Electronics Inc. - 5/143-...
  • Page 7 That is, each mobile station signal generates interference in relation to the signals of all the other mobile stations. LG Electronics Inc. - 6/143-...
  • Page 8 In addition, in the CDMA system, services and service charges are classified further into different classes so that more transmit power can be allocated to high class service users for easier call set-up; they can also be given higher priority of using hand-off function than the general users. LG Electronics Inc. - 7/143-...

  • Page 9: Structure And Functions Of Tri-Band Cdma Mobile Phone

    (AGC Amp). Then, they are converted into RF band by the frequency synthesizer synchronizing these signals to proper output frequencies. Transmit signals obtained pass through the duplexer filter and then, are sent out to the cell site via the antenna. LG Electronics Inc. - 8/143-...

  • Page 10: Specification

    4.1.10 Battery Type, Capacity and Operating Time. Unit = Hours : Minutes Standard (800mAh) CELLULAR About 165 Hours (SCI=2) Standby Time About 165 Hours (SCI=2) CELLULAR 140 Minutes (-92dBm input) Talk time 140 Minutes (-92dBm input) LG Electronics Inc. - 9/143-...

  • Page 11: Transmit Specification

    CELLULAR : 0.316W PCS: 0.316W 4.3.3 Interference Rejection Single Tone : -30dBm at 900 kHz (CELLULAR), -30dBm at 1.25MHz(PCS) Two Tone : -43dBm at 900 kHz & 1700kHz(CELLULAR), -43dBm at 1.25 MHz & 2.05 MHz (PCS) LG Electronics Inc. - 10/143-...
  • Page 12 Ch # Center Freq Ch # Center Freq Ch # Center Freq (MHz) (MHz) (MHz) 1851.25 1871.25 1891.25 1852.50 1872.50 1892.50 1853.75 1873.75 1893.75 1855.00 1875.00 1895.00 1856.25 1876.25 1896.25 1857.50 1877.50 1897.50 1858.75 1878.75 1898.75 LG Electronics Inc. - 11/143-...
  • Page 13 Center Freq Ch # (MHz) (MHz) (MHz) 1931.25 1951.25 1971.25 1932.50 1952.50 1972.50 1933.75 1953.75 1973.75 1935.00 1955.00 1975.00 1936.25 1956.25 1976.25 1937.50 1957.50 1977.50 1938.75 1958.75 1978.75 1940.00 1960.00 1000 1980.00 1941.25 1961.25 1025 1981.25 LG Electronics Inc. - 12/143-...
  • Page 14 1943.75 1963.75 1075 1983.75 1945.00 1965.00 1100 1985.00 1946.25 1966.25 1125 1986.25 1947.50 1967.50 1150 1987.50 1948.75 1968.75 1175 1988.75 4.5.3 GPS mode : 1575.42 MHz 4.5.4 Bluetooth mode : 2400 MHz ~ 2483.5 MHz LG Electronics Inc. - 13/143-...

  • Page 15: Installation

    Clip the IB into the IB bracket. 5.3.4. Microphone Installation Install the microphone either by clipping I onto the sunvisor (driver’s side) or by attaching it to door post (driver’s side), using a velcro adhesive tape (not included). 5.3.5 Cable Connections LG Electronics Inc. - 14/143-...
  • Page 16 Connect the kit’s power cable connector to the interface box power receptacle. 5.3.5.2 Antenna Cable Connection Connect the antenna coupler cable connector from the cradle to the external antenna connector. ( Antenna is not included.) LG Electronics Inc. - 15/143-...
  • Page 17 ● Usually pressing soft key will save the change. ● To exit service program, press “END” key. 3) MEID/ESN You can see the MEID/ESN number. Press “OK” to edit more NAM1 items. Press “Exit” to exit Service Programming. LG Electronics Inc. - 16/143-...
  • Page 18 Press “EDIT” to edit MIN Phone Number. 6) NAM1 Home SID You can edit the NAM1 Home SID. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit Home SID. LG Electronics Inc. - 17/143-...
  • Page 19 Press “More” to edit more advanced NAM1 items. 9) Security Code You can decide to edit Security Code. Press “OK” to edit more advanced NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT’ to edit security code. LG Electronics Inc. - 18/143-...
  • Page 20 Press “EDIT” to edit NAM1 NMSID. 12) NAM1 True IMSI MCC You can edit NAM1 True IMSI MCC. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit NAM1 True IMSI MCC. LG Electronics Inc. - 19/143-...
  • Page 21 Press “OK” to edit more NAM1 items. Press “ BACK” to edit previous NAM1 items. 15) CDMA Home SID/NID You can edit NAM1 Home SID/NID pair. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. LG Electronics Inc. - 20/143-...
  • Page 22 Press “EDIT” to edit Secondary CH A. 18) NAM1 CDMA Pri. CH B You can edit NAM1 CDMA Primary Channel B. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit LG Electronics Inc. - 21/143-...
  • Page 23 Press “BACK” to edit previous NAM1 items. 21) NAM1 Home Sys. Reg. You can edit NAM1 Home System Registration. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit Home System Registration. LG Electronics Inc. - 22/143-...
  • Page 24 Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit Foreign NID Reg. 24) NAM1 ACC Ovld Class You can edit NAM1 Access Overload Class. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. LG Electronics Inc. - 23/143-...
  • Page 25 Press “BACK” to edit previous items. 27) Slot Cycle Index You can edit Slot Cycle Index. Press “OK” to edit more NAM1 items. Press “BACK” to edit previous NAM1 items. Press “EDIT” to edit Slot Cycle Index. LG Electronics Inc. - 24/143-...
  • Page 26 VX11000 28) Powering Down Restart. LG Electronics Inc. - 25/143-...

  • Page 27: Chapter 3. Circuit Description

    After that, the RF signal is amplified by the Power Amp in order to have enough power for radiation. Finally, the RF signal is sent out to the cell site via the antenna after going through the Quintplexer. LG Electronics Inc. - 26/143-...
  • Page 28 VX11000 [Figure 1-1] RF Block Diagram of VX11000 LG Electronics Inc. - 27/143-...
  • Page 29 The main function of quintplexer is to prohibit the other band signals from flowing into the one band circuit and vice versa. RF designer can use common tri-band antenna regardless of frequency band (800, 1575 and 1900 MHz). The specification of VX11000 quintplexer is described below: LG Electronics Inc.
  • Page 30 VX11000 LG Electronics Inc. - 29/143-...
  • Page 31 The characteristics of Low Noise Amplifier (LNA) are low noise figure, high gain, high intercept point and high reverse isolation. The frequency selectivity characteristic of mobile phone is mostly determined by LNA. The specification of VX11000 GPS LNA is described below Parameter...
  • Page 32 Intercept Point (IIP3) requirements of IS-98D and J-STD-018 specifications for Sensitivity, Two-Tone Inter- modulation, and Single-tone Desensitization. Operation modes and band selection are specially controlled from the Mobile Station Modem MSM7500A. The specification of VX11000 Mixers is described below: Low gain High gain...
  • Page 33 19.2 MHz. The receiver frequency tuning signals called TRK_LO_ADJ from MSM as 0.4 V~2.4 V DC via R and C filter in order to generate the reference frequency of 19.2 MHz and input it into the frequency synthesizer. Frequency stability depending on temperature is ±1.5 ppm. LG Electronics Inc. - 32/143-...

  • Page 34: Digital/Voice Processing Part

    The memory part is made up of a NAND Flash memory and a SDRAM for storing data. 2.2.5 Power Supply Part The power supply part is made up of circuits for generating various types of power, used for the digital/voice processing part. LG Electronics Inc. - 33/143-...
  • Page 35 (AMSS) for building handsets based on the MSM7500A chipset. AMSS software is designed to run on a SURF phone platform, an optional development platform optimized to assist in evaluating, testing, and debugging AMSS software. LG Electronics Inc. - 34/143-...
  • Page 37 LCD Controller S1D13775 will display the information onto the LCD by 24-bit data from the MSM7500A. LCD Module is supplied stable +2.8V_LCD by Out3 in U4001 for fine view angle and LCD reflects to improve the display efficiency. 6 LEDs is used to display each LCD backlight. LG Electronics Inc. - 36/143-...
  • Page 38 It supports I2S audio data format between DSP and codec. A speaker amplifier, using digital amplifier system, realizes low power consumption than that of linear amplifier. In addition, power-down mode is available to minimize the current consumption when used. LG Electronics Inc. - 37/143-...

  • Page 39: Chapter 4. Trouble Shooting

    - Sector Power: - 30 dB m Spectrum Analyzer Setting Oscilloscope Setting 3. Check Control signal, RF Signal path 1. Check DC Power Supply circuit 4. Check Rx I/Q data 2. Check VCTCXO Redownload S/W, Cal LG Electronics Inc. - 38/143-...
  • Page 40 VX11000 4.1.1.1 Checking DC Power supply circuit (PMIC) Test Point Test Point R4031 C4094 C4093 MAX8694 LP8720TLX RTR6500 Circuit Diagram Circuit Diagram LG Electronics Inc. - 39/143-...
  • Page 41 + 2 .1 V_ RX1 is OK ? Refer to Logic troubleshoot Check R4031 The Problem may be Lo gic part Refer to Logic troubleshoot +2.6V_MSMP is OK? DC Po wer supply Circuit is OK. See next Page to check VCTCXO circuit LG Electronics Inc. - 40/143-...
  • Page 42 VX11000 4.1.1.2 Checking VCTCXO circuit Test Point Test Point R1002 C1101 Circuit Diagram Circuit Diagram LG Electronics Inc. - 41/143-...
  • Page 43 Replace U 1003 and then check R1002 , Pin3. VCTCXO circuit is Ok . See next page Is it similar? to check control signal . Replace Main B /D Waveform Waveform Figure 4.1.1 (a) Figure 4.1.1 (b) LG Electronics Inc. - 42/143-...
  • Page 44 VX11000 4.1.1.3 Checking RF signal path (Mobile S/W, Quintplexer) Test Point Test Point VCTCXO RTR6500 Quintplex Mobile switch Circuit Diagram Circuit Diagram LG Electronics Inc. - 43/143-...
  • Page 45 To Figure 4.1.1 (d ). Is any signal detected at that point? Is any signal detected at Check L1007, L1009, C1037 that point? RF signal path is OK. See next page to Rx I/Q data signal LG Electronics Inc. - 44/143-...
  • Page 46 VX11000 Waveform Waveform U1002 pin2 4.1.1 (c) DP1000 pin1 4.1.1 (d) LG Electronics Inc. - 45/143-...
  • Page 47 VX11000 4.1.1.4 Checking Rx I/Q data Test Point Test Point RTR6500 U1009 Pin55 (RX0_IP) Pin56 (RX0_IM) Pin57 (RX0_QP) Pin58 (RX0_QM) Circuit Diagram Circuit Diagram LG Electronics Inc. - 46/143-...
  • Page 48 To Figure 4.1.1 (e), (f) All DCN Rx check is completed . If the phone still do not work , change Main B /D . Waveform Waveform RX0_QP RX0_IP RX0_IM RX0_QM Graph 4.1.1(e) Graph 4.1.1(f) LG Electronics Inc. - 47/143-...
  • Page 49 - Sect or Power: - 30 dB m Spec trum Analyzer Setting Osc illosc ope Setting 3. Check Control signal, RF Signal path 1. Check DC Power Supply circuit 4. Check Rx I/Q data 2. Check VCTCXO Redownload S/W, Cal LG Electronics Inc. - 48/143-...
  • Page 50 VX11000 4.1.2.1 Checking DC Power supply circuit (PMIC) Test Point Test Point R4031 C4094 C4093 MAX8694 LP8720TLX RTR6500 Circuit Diagram Circuit Diagram LG Electronics Inc. - 49/143-...
  • Page 51 + 2 .1 V_ RX1 is OK ? Refer to Logic troubleshoot Check R4031 The Problem may be Lo gic part Refer to Logic troubleshoot +2.6V_MSMP is OK? DC Po wer supply Circuit is OK. See next Page to check VCTCXO circuit LG Electronics Inc. - 50/143-...
  • Page 52 VX11000 4.1.2.2 Checking VCTCXO circuit Test Point Test Point R1002 C1101 Circuit Diagram Circuit Diagram LG Electronics Inc. - 51/143-...
  • Page 53 Replace U 1003 and then check R1002 , Pin3. VCTCXO circuit is Ok . See next page Is it similar? to check control signal . Replace Main B /D Waveform Waveform Figure 4.1.2 (a) Figure 4.1.2 (b) LG Electronics Inc. - 52/143-...
  • Page 55 Check if there is any major difference referring Replace DP1000 To Figure 4.1.2 (d ). Is any signal detected at that point? RF signal path is OK. See next page to Rx I/Q data signal LG Electronics Inc. - 54/143-...
  • Page 56 VX11000 Waveform Waveform U1002 pin2 4.1.2 (c) DP1000 pin2 4.1.2 (d) LG Electronics Inc. - 55/143-...
  • Page 57 VX11000 4.1.2.4 Checking Rx I/Q data Test Point Test Point RTR6500 U1009 Pin55 (RX0_IP) Pin56 (RX0_IM) Pin57 (RX0_QP) Pin58 (RX0_QM) Circuit Diagram Circuit Diagram LG Electronics Inc. - 56/143-...
  • Page 58 To Figure 4.1.2 (e), (f) All DCN Rx check is completed . If the phone still do not work , change Main B /D . Waveform Waveform RX0_QP RX0_IP RX0_IM RX0_QM Graph 4.1.2 (e) Graph 4.1.2 (f) LG Electronics Inc. - 57/143-...
  • Page 59 Rx TEST SETUP (HHP) - Test Channel: 384 - Test Band : US Cellular - SID: - Sector Power: - 30 dB m Spectrum Analyzer Setting Oscilloscope Setting 1. Check Control signal, RF Signal path Redownload S/W, Cal LG Electronics Inc. - 58/143-...
  • Page 60 VX11000 4.1.3.1 Checking DCN RF Diversity signal path (Mobile S/W, Diplexer, SAW Filter) Test Point Test Point C1011 C1064 RTR6500 Diversity Mobile S/W C1026 Circuit Diagram Circuit Diagram LG Electronics Inc. - 59/143-...
  • Page 61 To Figure 4.1.3 ( c ). Is any signal detected at that point? Is any signal detected at Check C1026, L1006, C1027 that point? RF signal path is OK. See next page to Rx I/Q data signal LG Electronics Inc. - 60/143-...
  • Page 62 VX11000 Waveform Waveform U1000 pin2 4.1.3 (a) F1000 pin4 4.1.3 (b) F1001 pin4 4.1.3 (c) LG Electronics Inc. - 61/143-...
  • Page 63 - Tes t Band : U S PCS - SID: 5269 - Sect or Power: - 30 dB m Spec trum Analyzer Setting Osc illosc ope Setting 1. Check Control signal, RF Signal path Redownload S/W, Cal LG Electronics Inc. - 62/143-...
  • Page 64 VX11000 4.1.4.1 Checking PCS RF Diversity signal path (Mobile S/W, Diplexer, SAW Filter) Test Point Test Point C1010 C1064 RTR6500 Diversity Mobile S/W L1004 Circuit Diagram Circuit Diagram LG Electronics Inc. - 63/143-...
  • Page 65 To Figure 4.1.4 ( c ). Is any signal detected at that point? Is any signal detected at Check L1004, L1005, C1029 that point? RF signal path is OK. See next page to Rx I/Q data signal LG Electronics Inc. - 64/143-...
  • Page 66 VX11000 Waveform Waveform U1000 pin2 4.1.4 (a) F1000 pin6 4.1.4 (b) F1002 pin4 4.1.4 (c) LG Electronics Inc. - 65/143-...
  • Page 67 ? Measure frequency domain waveform with Spectrum Dual PAM analyser ? Measure time domain waveform with Oscilloscope 1. Check 6. Check DC Power Supply circuit Quintplexer 2. Check 7. Check VCTCXO Mobile Switch 3. Check RTR6500 Redownload S/W, Cal LG Electronics Inc. - 66/143-...
  • Page 68 VX11000 4.2.1.1 Checking DC Power supply circuit (PMIC) Test Point Test Point R4031 LP8720TLX R1012 MAX8694 RTR6500 Circuit Diagram Circuit Diagram LG Electronics Inc. - 67/143-...
  • Page 69 The Pr o ble m m ay b e Lo gic part + 2.6V_MSMP is OK? Refer to Lo gic troub les hoot DC Po wer su p ply Circuit is OK. See next Page to c hec k VCTCXO circuit LG Electronics Inc. - 68/143-...
  • Page 70 VX11000 4.2.1.2 Checking VCTCXO circuit Test Point Test Point R1002 C1101 Circuit Diagram Circuit Diagram LG Electronics Inc. - 69/143-...
  • Page 71 Replace U 1003 and then check R1002 , Pin3. VCTCXO circuit is Ok . See next page Is it similar? to check control signal . Replace Main B /D Waveform Waveform Figure 4.2.1.2 (a) Figure 4.2.1.2 (b) LG Electronics Inc. - 70/143-...
  • Page 72 VX11000 4.2.1.3 Checking RTR6500 DCN circuit Test Point Test Point Pin16(TP2) C1093 C1101 (TP1) (TP3) Circuit Diagram Circuit Diagram LG Electronics Inc. - 71/143-...
  • Page 73 Check pin16 at U1009(TX _ON signal ) Check TX_ON signal & MSM whether it is higher than 2.5V. Check C1101 at U 1009 (TCXO signal) Check TCXO circuit. referring to Figure 4.2.1.3 (b). Is it similar? Replace U1005 LG Electronics Inc. - 72/143-...
  • Page 74 VX11000 Waveform Waveform Figure 4.2.1.3(a) Figure 4.2.1.3(b) LG Electronics Inc. - 73/143-...
  • Page 75 Checking Flow Waveform Start RF_IN fed up with CW signal RF_IN Check Pin1,4 at F1005 . Referring to RF Tx SAW is OK Figure 4.2.1. . Is it similar ? Replace F 1005 RF_OUT Figure 4.2.1.4 LG Electronics Inc. - 74/143-...
  • Page 76 VX11000 4.2.1.5 Check Dual PAM DCN circuit Test Point Test Point RF_IN VEN_CELL VMOD VCC1 CELL VCC2 RF_OUT CELL Circuit Diagram Circuit Diagram PCS Tx DCN Tx LG Electronics Inc. - 75/143-...
  • Page 77 Check pin3 at U1008 (PA _R0 ) Check PA_R0 line whether it is lower than 2.2V. Replace U1008 Waveform Waveform RF_IN fed up with CW signal in Bypass mode of PAM RF_IN RF_OUT Figure 4.2.1.5 LG Electronics Inc. - 76/143-...
  • Page 78 Waveform Checking Flow Waveform Start CELL TX Port Check pin3 , 5 at DP1000. Referring to Quintplexer is OK Figure 4 .2 .1 .6. Is it similar ? Replace DP 1000 ANT_1 Port Figure 4.2.1.6 LG Electronics Inc. - 77/143-...
  • Page 79 Waveform Checking Flow Waveform Start INPUT Port Check pin1 , 2 Mobile S /W is at U 1002. Referring to Figure 4 .2 .1 .7. Is it similar ? Replace U1002 OUTPUT Port Figure 4.2.1.7 LG Electronics Inc. - 78/143-...
  • Page 80 ? Measure frequency domain waveform with Spectrum Dual PAM analyser ? Measure time domain waveform with Oscilloscope 1. Check 6. Check DC Power Supply circuit Quintplexer 2. Check 7. Check VCTCXO Mobile Switch 3. Check RTR6500 Redownload S/W, Cal LG Electronics Inc. - 79/143-...
  • Page 81 VX11000 4.2.2.1 Checking DC Power supply circuit (PMIC) Test Point Test Point R4031 LP8720TLX R1012 MAX8694 RTR6500 Circuit Diagram Circuit Diagram LG Electronics Inc. - 80/143-...
  • Page 82 The Pr o ble m m ay b e Lo gic part + 2.6V_MSMP is OK? Refer to Lo gic troub les hoot DC Po wer su p ply Circuit is OK. See next Page to c hec k VCTCXO circuit LG Electronics Inc. - 81/143-...
  • Page 83 VX11000 4.2.2.2 Checking VCTCXO circuit Test Point Test Point R1002 C1101 Circuit Diagram Circuit Diagram LG Electronics Inc. - 82/143-...
  • Page 84 Replace U 1003 and then check R1002 , Pin3. VCTCXO circuit is Ok . See next page Is it similar? to check control signal . Replace Main B /D Waveform Waveform Figure 4.2.2.2 (a) Figure 4.2.2.2 (b) LG Electronics Inc. - 83/143-...
  • Page 85 VX11000 4.2.2.3 Checking RTR6500 PCS circuit Test Point Test Point Pin16(TP2) C1101 C1092 (TP3) (TP1) Circuit Diagram Circuit Diagram LG Electronics Inc. - 84/143-...
  • Page 86 Check pin16 at U1009(TX _ON signal ) Check TX_ON signal & MSM whether it is higher than 2.5V. Check C1101 at U 1009 (TCXO signal) Check TCXO circuit. referring to Figure 4.2.2.3 (b). Is it similar? Replace U1006 LG Electronics Inc. - 85/143-...
  • Page 87 VX11000 Waveform Waveform Figure 4.2.2.3(a) Figure 4.2.2.3(b) LG Electronics Inc. - 86/143-...
  • Page 88 RF_IN fed up with CW signal RF_IN Check pin 1 , 4 at F 1006 Referring to RF Tx SAW is Figure 4 .2 .2 . 4. Is it similar ? Replace F 1006 RF_OUT Figure 4.2.2.4 LG Electronics Inc. - 87/143-...
  • Page 89 VX11000 4.2.2.5 Check Dual PAM PCS circuit Test Point Test Point RF_IN VEN_PCS VMOD VCC1 RF_OUT VCC2 Circuit Diagram Circuit Diagram PCS Tx DCN Tx LG Electronics Inc. - 88/143-...
  • Page 90 Check pin3 at U1008 (PA _R0 ) Check PA_R0 line whether it is lower than 2.2V. Replace U1008 Waveform Waveform RF_IN fed up with CW signal in Bypass mode of PAM RF_IN RF_OUT Figure 4.2.2.5 LG Electronics Inc. - 89/143-...
  • Page 91 ANT1 Checking Flow Waveform Checking Flow Waveform Start PCS TX Port Check pin4 , 5 at DP1000 Referring to Quintplexer is OK Figure 4.2.2.6. Is it similar ? Replace DP 1000 ANT_1 Port Figure 4.2.2.6 LG Electronics Inc. - 90/143-...
  • Page 92 Waveform Checking Flow Waveform Start INPUT Port Check pin1 , 2 Mobile S /W is at U 1002. Referring to Figure 4 .2 .2 .7. Is it similar ? Replace U1002 OUTPUT Port Figure 4.2.2.7 LG Electronics Inc. - 91/143-...

  • Page 93: Logic Part Trouble Shooting

    VX11000 4.3 Logic Part Trouble Shooting 4.3.1 Power 4.3.1.1 Power-On Trouble Circuit Diagram Circuit Diagram +VBATT +1.25V_MSMC1 +2.6V_MSMP +1.25V_MSMC2 +2.6V_MSMA PMIC (U4001) +1.8V_MSME +2.85V_TCXO TCXO_IN TCXO_OUT LG Electronics Inc. - 92/143-...

  • Page 94: Circuit Diagram2

    VX11000 Circuit Diagram2 Circuit Diagram2 PS_HOLD PMIC (U4001) SLEEP_CLK USBH_CS (U5004) LG Electronics Inc. - 93/143-...

  • Page 95: Test Point

    VX11000 Test point Test point +1.25V_MSMC2 PS_HOLD SLEEP_CLK +1.25V_MSMC1 +1.8V_MSME PMIC +VBATT U4001 +2.6V_MSMP +2.6V_MSMA TCXO_IN +2.85V_TCXO TCXO_OUT TCXO U1003 LG Electronics Inc. - 94/143-...
  • Page 96 Replace PMIC (U4001) +1.8V_MSME +2.6V_MSMP +2.6V_MSMA +2.85V_TCXO Is the frequency of TCXO_IN Replace TCXO (U1003) (C4114) 19.2Mhz? Is TCXO_OUT (C4136) Replace TCXO BUFFER (U4006) 19.2Mhz, Pk-Pk 2.85V? Is SLEEP_CLK (C4042) Replace Sleep Crystal (U4000) 32.76Khz, Pk-Pk 2.6V? LG Electronics Inc. - 95/143-...
  • Page 97 VX11000 Checking Flow Checking Flow Logic level of USBH_CS=High after 15s? download software try again Logic level of Replace MSM (U202) PS_HOLD=High? Does it work properly? Change the board Change the board LG Electronics Inc. - 96/143-...

  • Page 98: Charging Trouble

    VX11000 4.3.1.2 Charging Trouble Circuit Diagram Circuit Diagram +5V_VCHAR ACCESSORY_ADC CON5001 USB_DETECT +VBATT CHG_MODE LG Electronics Inc. - 97/143-...
  • Page 99 VX11000 Test point Test point +VBATT CHG_MODE +5V_VCHAR USB_DETECT ACCESSORY_ADC CON5001 LG Electronics Inc. - 98/143-...
  • Page 100 Replace PMIC (U4001) Check VBATT Voltage >3.4V Service Menu -> H/W test -> ETC GetADC(ACC) 100~150 GetADC(BATT_THM) 1~210 ? When the phone is charged, Change the MSM (U2000) CHG_MODE(R5019)=0V? LG Electronics Inc. - 99/143-...
  • Page 101 VX11000 Checking Flow Checking Flow USB_DETECT If connect USB Cable, 2.6V Replace Q5000 If connect TA, 0V ? download software try again Change the board Does it work properly Charging will operate properly LG Electronics Inc. - 100/143-...

  • Page 102: Camera Trouble

    VX11000 4.3.2 Camera trouble Circuit Diagram Circuit Diagram • Camera Control signals To MSM : CAM_DATA[0:7], CAM_RESET/, CAM_I2C_SDA, CAM_I2C_SCL, CAM_OSC_MCLK, CAM_PCLK Test Point Test Point C6001 C6002 C6040 CON6000 R6013 C6039 R6004 U6000 LG Electronics Inc. - 101/143-...

  • Page 103: Check Flow

    Check the voltage of the following camera power : +2.8V_CAM_VDDA Replace the U4001, U4002 +2.6V_CAM_VDDIO +1.8V_CAM_VDD +2.8V_CAM_LVDD Check the Control signal CAM_DATA[0:7], CAM_RESET/, Check the CON6000 CAM_SDA, CAM_SCL Check CON7007 Soldering Re-soldering CON6000 Camera will work properly LG Electronics Inc. - 102/143-...

  • Page 104: Flash Led Trouble

    VX11000 4.3.3 Flash LED trouble Circuit Diagram Circuit Diagram Test Point Test Point R431 C432 CON6002 U6002 R6007 C6036 LG Electronics Inc. - 103/143-...
  • Page 105 5 of U6002 Check the control signal Check the MSM at R6007 Check Flash LED driver Replace the U6002 output at C6036 Check CON6002 Soldering Re-soldering CON6002 Replace the Flash LED module Camera will work properly LG Electronics Inc. - 104/143-...
  • Page 107 VX11000 Test Point Test Point R4049 U7001 U4006 RGB_DCLK F6004 CON6001 R6049 LG Electronics Inc. - 106/143-...
  • Page 108 +1.8V_MSME +1.5V_RGB Check the voltage of LDC power : Replace U4001 +2.8V_LCD Check the Control signal RGB_DATA[0:23] , RGB_VSYNC, Check the CON6001 RGB_HSYNC, RGB_DATA_EN, RGB_DCLK Check CON6001 Soldering Re-soldering CON 6001 LCD will work properly LG Electronics Inc. - 107/143-...

  • Page 109: Lcd Backlight Trouble

    VX11000 4.3.4.2 LCD Backlight trouble Circuit Diagram Circuit Diagram Internal LCD Backlight External LCD Backlight Test Point Test Point R5018 TP5002 R5026 R5027 R5004 TP5000 LG Electronics Inc. - 108/143-...
  • Page 110 External LCD Backlight START Check the U5005 soldering Check the I2C at R5018 Check the Reset at TP5002 Check the U5005 soldering Check the LED output at Check the CON6001 R5027 LCD Backlight will work properly LG Electronics Inc. - 109/143-...
  • Page 111 VX11000 4.3.5 Audio 4.3.5.1 Speaker Trouble Circuit Diagram Circuit Diagram LG Electronics Inc. - 110/143-...
  • Page 112 VX11000 Test Point Test Point C3016 C3020 C3021 C6016 C6017 C6018 C6019 LG Electronics Inc. - 111/143-...
  • Page 113 Replace speaker& Check the audio signal at Check the soldering at proximity cal after SET assembly SPK contact pad SPK+, SPK- contact pad Resolder the speaker& proximity cal after SET assembly Speaker will work properly LG Electronics Inc. - 112/143-...
  • Page 114 VX11000 4.3.5.2 Receiver Trouble Circuit Diagram Circuit Diagram Test Point Test Point LG Electronics Inc. - 113/143-...
  • Page 115 Replace the receiver & Check the audio signal at Check the soldering at proximity cal after SET assembly RCV contact pad RCV+, RCV- contact pad Resolder the receiver & proximity cal after SET assembly Receiverwill work properly LG Electronics Inc. - 114/143-...
  • Page 116 VX11000 4.3.5.3 Headset Trouble Circuit Diagram Circuit Diagram < Audio Amp part > < Ear jack part > LG Electronics Inc. - 115/143-...
  • Page 117 VX11000 Test Point Test Point C3016 C3020 C3021 C3026 C3025 C3024 C3022 LG Electronics Inc. - 116/143-...
  • Page 118 ? Set the audio part of the test equipment to continuous wave mode Can you hear the Headset RX Sound from headset ? path problem Headset TX path problem Headset will work properly LG Electronics Inc. - 117/143-...
  • Page 119 Checking Flow: Headset TX path problem Checking Flow: Headset TX path problem Check the voltage C3026 Replace MSM or B/D Check the soldering of CON3000 whether its range is high ? Resolder CON3000 with heat gun Replace CON3000 LG Electronics Inc. - 118/143-...
  • Page 120 VX11000 4.3.5.4 MIC Trouble Circuit Diagram Circuit Diagram Test Point Test Point C2006 R2001 LG Electronics Inc. - 119/143-...
  • Page 121 Check the voltage level at R2001 Check the soldering Replace MSM or Main B/D Whether its range is 1.5~2.0V at R2001 Resolder R2001 Check the signal level at Resolder M2000 Each side of MIC, C2006 MIC will work properly LG Electronics Inc. - 120/143-...
  • Page 122 VX11000 4.3.6 Touch and Keypad 4.3.6.1 Touch Trouble Circuit Diagram Circuit Diagram LG Electronics Inc. - 121/143-...
  • Page 123 VX11000 Test Point Test Point U7004 LG Electronics Inc. - 122/143-...
  • Page 124 Replace Main PCB C6061, C6062, is there any pulse When you press touch ? Replace the LCD FPCB & Check the contact state proximity cal after SET assembly of the FPCB connector Touch key will work properly LG Electronics Inc. - 123/143-...
  • Page 125 VX11000 4.3.6.2 Numeric key backlight Circuit Diagram Circuit Diagram VPWR Drain of Switching Gate of Switching FET Test point Test point Gate of Switching Drain of Switching FET LG Electronics Inc. - 124/143-...
  • Page 126 Charge battery 3.3 ~ 4.2V? Check the soldering of each R andLEDS, Are all LEDs working? or replace if not wor king Is Q5001 Working? Replace Q 5001 Main key backlight w ill work properly LG Electronics Inc. - 125/143-...
  • Page 127 VX11000 4.3.7 Vibrator Circuit Diagram Circuit Diagram Test point Test point U7002 U7000 U7005 LG Electronics Inc. - 126/143-...
  • Page 128 Start Change the main board Check the Voltage of TP1 =3.0V? Is U7000, U7002 Working? Replace the U7000, U7002 Check the state at contact of vibrator Re-contact vibrator Replace Vibrator The vibrator will Work properly LG Electronics Inc. - 127/143-...
  • Page 129 If so, use only a manufacture approves antenna. Otherwise, take your phone to a qualifies service center for repair. Use only the supplied or approved antenna. Non-approved antennas, modifications, or attachments, could impair call quality, damage the phone, and violate FCC regulations. LG Electronics Inc. - 128/143-...

  • Page 130: Blasting Areas

    LG Electronics Inc. - 129/143-...
  • Page 131 Park, Quincy, MA 02269, Attn: Publication Sales Division. Rule of Thumb: Using common sense at all times when handling, installing or using the phone. Any questions should be directed to you nearest Service Center or authorized service technician or electrician. LG Electronics Inc. - 130/143-...

  • Page 132: Chapter 6. Glossary

    A-key. A secret, 64-bit pattern stored in the mobile station. It is used to generate update the mobile station’s Shared Secret Data. The A-key is used in the mobile station authentication process. LG Electronics Inc. - 131/143-...
  • Page 133 Neighbor Set, and Remaining Set. . See Code Division Multiple Access CDMA Channel. The set of channels transmitted between the base station within a given CDMA frequency assignment. See also Forward CDMA Channel and Reverse CDMA Channel. LG Electronics Inc. - 132/143-...
  • Page 134 Digital Color Code (DCC). A digital signal transmitted by a base station on a forward analog control channel that is used to detect capture of a base station by an interfering mobile station. Dim-and-Burst. A frame in which primary traffic is multiplexed with either secondary traffic or signaling traffic. LG Electronics Inc. - 133/143-...
  • Page 135 Channels. The Forward CDMA Channel always carries a Pilot Channel and may carry up to one Sync Channel, up to seven Paging Channels, and up to 63 Traffic Channels, as long as the total number of channels, including the Pilot Channel, is no greater than 64. LG Electronics Inc. - 134/143-...
  • Page 136 Layer 2. Layer 2 provides for the correct transmission and reception of signaling messages, including partial duplicate detection. See also Layering and Layer 3. Layer 3. Layer 3 provides the control of the Cellular telephone systems. Signaling messages originate and terminate at layer 3. See also Layering and Layer 2. LG Electronics Inc. - 135/143-...
  • Page 137 Mobile Station Terminated Call. A call received by a mobile station (not to be confused with a disconnect or call release). Mobile Switching Center (MSC). A configuration of equipment that provides Cellular radiotelephone service. Also called the Mobile Telephone Switching Office (MTSO) LG Electronics Inc. - 136/143-...
  • Page 138 OLC. See Overload Class (CDMA) or Overload Control (analog). Optional Field. A field defined within a message structure that is optionally to the message recipient. Order. A type of message that contains control codes for either the mobile station or the base station. LG Electronics Inc. - 137/143-...
  • Page 139 CDMA Channel and the Reserve CDMA Channel. Different base station are identified by different pilot PN sequence offsets. Pilot PN Sequence Offset Index. The PN offset in units of 64 PN chips of a pilot, relative to the zero offset pilot PN sequence. LG Electronics Inc. - 138/143-...
  • Page 140 Active Set, Candidate Set, and Neighbor Set. See also Active Set, Candidate Set, and Neighbor Set. Request. A layer 3 message generated by either the mobile station or the base station to retrieve information, ask for service, or command an action. LG Electronics Inc. - 139/143-...
  • Page 141 Slot Cycle. A periodic interval at which a mobile station operating in the slotted monitors the Paging Channel. Slotted Mode. An operation mode of the mobile station in which the mobile station monitors only selected slots on the Paging Channel when in the Mobile Station Idle State. LG Electronics Inc. - 140/143-...
  • Page 142 The counter is incremented an average of once per 80 ms period. Time Reference. A reference established by the mobile station that is synchronous with the earliest arriving multipath component used for demodulation. LG Electronics Inc. - 141/143-...
  • Page 143 ‘0’ to 1 and ‘1’ to –1). Zone-Based Registration. An autonomous registration method in which the mobile station registers whenever it enters a zone that is not in the mobile station’s zone list. ㎲. Microsecond LG Electronics Inc. - 142/143-...

  • Page 146: Block Diagram

    Block Diagram...

  • Page 147: Phone Block Diagram

    Internal Use Only Touch Screen Battery Battery Phone Block Diagram...

  • Page 148: Rf Block Diagram

    Internal Use Only RF Block Diagram...

  • Page 149: Circuit Diagram

    Circuit Diagram (Main PCB/LCD FPCB /Sensor FPCB / Sidekey FPCB)

  • Page 150: Main Board Circuit

    Main Board Circuit...
  • Page 151 F1003 SIP4282 LG-VX11000 U1007 MAIN OUT2 6 +VBATT VIN1 TC7SH32FE OUT1 5 VIN2 PA_R0 +VDD_MSMP [DCN+USPCS] PA_R1 ON/OFF PA_R_OR LOAD_SW_EN F1005 Internal Use Only ANT1000 ANT1001 ANT1002 B9425 C1030 C1035 C1075 +VDD_TX_A C1047 C1058 U1002 +2.1V_TX_SYNTH KMS-518 L1029 L1003 C1003 +2.1V_TX...
  • Page 152 LG-VX11000 Internal Use Only +3.0V_QFUSE +1.8V_MSME +2.6V_MSMP +1.8V_MSME +1.2V_MSMC2 +1.25V_MSMC1 VDD_A_1 +2.6V_MSMA VDD_A_2 VDD_A_3 VDD_A_4 AC27 VDD_A_5 EBI2_CS5_N AC28 VDD_A_6 EBI2_CS4_N AA24 USBH_CS EBI2_CS3_N 1.8V GPIO VDD_A_7 EBI2_CS2_N VDD_A_8 C2003 2.2n EBI2_CS1_N VDD_A_9 +2.6V_MSMA NAND_CS/ EBI2_CS0_N VDD_A_10 TX_I_P I_OUT_P VDD_A_11...
  • Page 153 LG-VX11000 Internal Use Only <AUDIO SUBSYSTEM> <Memory : 4G OneNand + 2G DDR SDRAM> +VBATT A1[0] C3012,C3015 : 3.9nF->1uF MIN+ A1[1] C3014,C3016 : 0.1uF->1uF MIN- A2[1] A1[2] A2[2] A1[3] LLS+ SPK_L+ C3012 HPH_L LIN+ A2[3] A1[4] LLS- SPK_L- C3014 LIN-...
  • Page 154 [AG7] [AG11] [AC2] [AG2] [AG5] [AG10] [N27] [U27] [AA27] [AD15] [K2] +1.2V_MSMC2 +1.2V_MSMC2 +1.2V_MSMC2 +1.8V_MSME +1.8V_MSME +1.8V_MSME LG-VX11000 Internal Use Only MSM_BT_TCXO_EN DVS_ARM9_HIGH_CLOCK/ +/-1% R4052 300k Dynamic Voltage Scaling for ARM9 +VBATT +VBATT U4005 +5.0V_USB +/-1% NLAS5223BMNR2G 1608 1608 510k 2.2u...
  • Page 155 <Battery Contact> LG-VX11000 Internal Use Only Q5003 TPCF8102 GU070-5P-SD-E1500 -> GU073-5P-SD-E1500 <Micro USB Connector> DRAIN6 DRAIN1 CON5000 R5020 GU073-5P-SD-E1500 F5001 80.6k DRAIN5 DRAIN2 NFM18PC104R1C3 +/-1% DRAIN4 DRAIN3 +2.6V_MSMA DUMMY3 +VBATT BATT_THM_ADC THM/ OUTPUT INPUT SOURCE GATE +/-1% DUMMY2 R5021 4.7k +2.6V_MSMP...
  • Page 156 LG-VX11000 Internal Use Only <34pin Camera Connector> <FLASH LED DRIVER> U6002 +1.8V_CAM_VDD AAT1270IFO-T1 R6002 CON6000 CAM_RESET/ AXK7L34227G RSET MOVIE_MODE_EN EN/SET FLOUTA +2.6V_CAM_VDDIO FLASH_EN FLEN FLGND FLASH_INHIBIT F6000 L6002 +2.6V_CAM_VDDIO AGND FLOUTB MIP2520D2R2M CON6002 +VBATT FLINH AXT310164 R6013 CAM_DATA[7] C6060 OUT4...
  • Page 157 LG-VX11000 Internal Use Only <Touch Driver> <Linear Motor> C7008 TOUCH_Y- 2.2n TOUCH_I2C_SDA R7014 100k TOUCH_I2C_SCL U7004 CON7000 TSC2007IYZGR R7017 24-8005-002-100-867 BYPASS LIN_AMP_SHDN/ SHUTDOWN +2.6V_TOUCH 100k A1 AUX TOUCH_X- R7004 A2 VDD_REF +2.6V_TOUCH R7001 U7000 A3 X+ TOUCH_X+ TC7SZ86FU TPA6205A1ZQVR U7005...
  • Page 158 LG-VX11000 Internal Use Only <micro-SD SOCKET> <PWR On Key> EXT. Folder EXT_ON_KEY Status CON8000 Preview SCHA5B0201 PWR/END Close EXT_ON = PWR_ON SW8022 R8029 SD_DATA[2] On("H") EXT_ON = PWR_ON PWR_ON_SW SD_DATA[3] +VBATT Open Off("L") EXT_ON = NULL SD_CMD +3.0V_SD R8028 SD_CLK...
  • Page 159 LCD FPCB Circuit...
  • Page 160 LG-VX11000 Internal Use Only <80PIN MAIN CONNECTOR> <70PIN LCD CONNECTOR> CON101 AXT680124 MLED6 SLED1 CON102 Mated Height : 1.0T -> 1.5T Changed AXT370164 (3.0X16.5X1.15 => 3.6X16.7X1.45) MLED5 SLED2 MLED4 SLED3 +2.85V_PROXI MLED3 SLED4 PROX_EN/ Deleted +2.8V_LCD MLED2 SLED5 PROXI_LED_ON +1.8V_MSME...
  • Page 161 Sensor FPCB Circuit...
  • Page 162 LG-VX11000 Internal Use Only <LCD 10PIN ZIP CONNECTOR> <RCV & SPK_R PAD> SURY0011303 (KR-1107H-02W1P, 10mm) CON100 FH19-10S-0_5SH-FPC RCV+ +2.85V_PROXI RCV- PROX_EN/ Deleted PROXI_LED_ON KR-1107H-02W1P PROXI_AOUT CON102 ALS_AOUT RCV- RCV+ SUSY0028013 (EMS1810TCD5P, 10mm) SPK_R- SPK_R+ SPK_R- U101 EMS1810THP1P SPK_R+ <LIGHT & PROXIMITY SENSOR>...
  • Page 163 Sidekey FPCB Circuit...
  • Page 164 LG-VX11000 Internal Use Only <CAMERA AUTO FOCUS> <HOLD/UP/DOWN> 5 B_ HOLD DOWN 6 C_ SW101 SW102 SW103 CON100 Dome Spec is Changed SIDEKEY_9PIN_FPCB_BOT EVPAHBD6A : Click Rate 45->60 SW100 KEY_SENSE[1] CAM1 (HALF) KEY_SENSE[2] CAM2 (FULL) KEY_DRIVE[8] COM1 HOLD HOLD DOWN...
  • Page 165 2. VX11000 BGA Pin Map...
  • Page 166 1. MSM7500A-64T (U2000) USED NOT USED BOTTOM VIEW...
  • Page 167 2. KBN00300-A439 (U3004) USED NOT USED BOTTOM VIEW...
  • Page 168 3. MAX8694 (U4001) Internal Use Only USED NOT USED...
  • Page 169 4. LP8720TLX (U4002) Internal Use Only USED NOT USED A1 Index Mark TOP VIEW...
  • Page 170 5. BD6088GUL (U5000, U5005) Internal Use Only USED NOT USED BOTTOM VIEW...
  • Page 171 6. LM49250RLX (U3001) Internal Use Only USED NOT USED BOTTOM VIEW...
  • Page 172 7. S1D13775B00B60L (U7001) Internal Use Only USED NOT USED BOTTOM VIEW...
  • Page 173 8. ISP1508AET (U5004) Internal Use Only USED NOT USED BOTTOM VIEW...
  • Page 174 9. BCM2046B1 (U7008) Internal Use Only USED NOT USED TOP VIEW...
  • Page 175 10. TSC2007IYZR (U7004) Internal Use Only USED NOT USED BOTTOM VIEW...
  • Page 177 LG-VX11000 Internal Use Only Triaxial Acceleration Sensor P/N:BMA150 Hall Effect S/W P/N:EM-0781-T5 Can’t Detect Folder Open...
  • Page 178 LG-VX11000 Internal Use Only 34 Pin Connector Stereo Ear-Jack P/N:AXK7L34227G P/N:KJA-PH-2-0174 Can’t Operate Camera Can’t Operate Earphone Camera Oscillator Quintplexer P/N:SG-8002CE-36M P/N:ACFM-7103 Can’t Operate Camera No Service Can’t Make a Call GPS LNA P/N:ALM-2412 Low GPS Sensitivity No GPS Service...
  • Page 179 LG-VX11000 Internal Use Only...
  • Page 180 LG-VX11000 Internal Use Only...
  • Page 181 LG-VX11000 Internal Use Only Ambient Light & Proximity Sensor P/N : QPDS-9800...
  • Page 182 LG-VX11000 Internal Use Only CON101 C’ B’ SW100 SW102 SW103 SW101...
  • Page 183 LG-VX11000 Internal Use Only...
  • Page 184 4. VX11000 Assembly & Disassembly Diagram...
  • Page 186 Internal Use Only...
  • Page 188 VX11000 Component List : Main PCB Ref No Part Name Part Number Spec Maker P/N SPFY00 PCB,MAIN SPFY0189501 FR-4 ,0.8 mm,STAGGERED-10 , ,; , , , , , , , , , SPFY0189501 SAFD00 PCB ASSY,MAIN,SMT TOP SAFD0117101 C6030 CAP,CERAMIC,CHIP...
  • Page 189 C1026 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C1005C0G1H101JT C1028 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C1005C0G1H101JT C1029 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C1005C0G1H101JT C1030 CAP,CERAMIC,CHIP ECCH0000122 47 pF,50V,J,NP0,TC,1005,R/TP MCH155A470JK C1032 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP...
  • Page 190 C1101 CAP,CHIP,MAKER ECZH0000813 100 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C1005C0G1H101JT C1102 CAP,CHIP,MAKER ECZH0004402 100000 pF,16V ,Z ,X7R ,TC ,1005 ,R/TP , , ,[empty] , MCH153C104ZK C1103 CAP,CHIP,MAKER ECZH0001215 1 uF,10V ,K ,X5R ,TC ,1005 ,R/TP C1005X5R1A105KT C1104 CAP,CERAMIC,CHIP ECCH0005604 10000000 pF,6.3V ,M ,X5R ,TC ,1608 ,R/TP , , ,[emp GRM188R60J106ME47D C1105 CAP,CHIP,MAKER...
  • Page 191 C4000 CAP,CHIP,MAKER ECZH0003103 0.1 uF,10V ,K ,X7R ,HD ,1005 ,R/TP GRM36X7R104K10PT C4001 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C4002 CAP,CERAMIC,CHIP ECCH0005604 10000000 pF,6.3V ,M ,X5R ,TC ,1608 ,R/TP , , ,[emp GRM188R60J106ME47D C4003 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C4004 CAP,CERAMIC,CHIP...
  • Page 192 C4062 CAP,CERAMIC,CHIP ECCH0000155 10 nF,16V,K,X7R,HD,1005,R/TP MCH153CN103KK C4063 CAP,CERAMIC,CHIP ECCH0000155 10 nF,16V,K,X7R,HD,1005,R/TP MCH153CN103KK C4064 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C4065 CAP,CERAMIC,CHIP ECCH0005604 10000000 pF,6.3V ,M ,X5R ,TC ,1608 ,R/TP , , ,[emp GRM188R60J106ME47D C4066 CAP,CERAMIC,CHIP ECCH0000155 10 nF,16V,K,X7R,HD,1005,R/TP MCH153CN103KK C4067...
  • Page 193 C4123 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C4124 CAP,CHIP,MAKER ECZH0001421 2.2 uF,6.3V ,K ,X5R ,HD ,1608 ,R/TP C1608X5R0J225KT C4125 CAP,CHIP,MAKER ECZH0001421 2.2 uF,6.3V ,K ,X5R ,HD ,1608 ,R/TP C1608X5R0J225KT C4126 CAP,CHIP,MAKER ECZH0001215 1 uF,10V ,K ,X5R ,TC ,1005 ,R/TP C1005X5R1A105KT C4127 CAP,CERAMIC,CHIP...
  • Page 194 C6022 CAP,CERAMIC,CHIP ECCH0009104 33 pF,50V ,J ,X7R ,TC ,0603 ,R/TP C0603C0G1H330JT C6023 CAP,CERAMIC,CHIP ECCH0009104 33 pF,50V ,J ,X7R ,TC ,0603 ,R/TP C0603C0G1H330JT C6024 CAP,CERAMIC,CHIP ECCH0009104 33 pF,50V ,J ,X7R ,TC ,0603 ,R/TP C0603C0G1H330JT C6025 CAP,CERAMIC,CHIP ECCH0009104 33 pF,50V ,J ,X7R ,TC ,0603 ,R/TP C0603C0G1H330JT C6026 CAP,CERAMIC,CHIP...
  • Page 195 C7033 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C1005C0G1H270JT C7034 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C7035 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C7036 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP GRM36X5R104K10PT C7037 CAP,CERAMIC,CHIP...
  • Page 196 F6010 FILTER,EMI/POWER SFEY0011701 SMD ,SMD ,18 V,4ch. EMI_ESD Filter (10 Ohm,7.5pF ICVE10184E070R100FR F7000 FILTER,CERAMIC SFCY0000901 2450 MHz,2.00*1.25*0.95 ,SMD ,Bluetooth Band Pas LFB212G45SG8A166 F7001 EUSY0353701 PLP1010-4 ,4 PIN,R/TP ,1x1 LDO, 2.6V , 150mA ,; ,IC RP104K261D F8000 EUSY0365101 PLP1612-4B ,4 ,R/TP ,LDO ,; ,IC,LDO Voltage Regul RP101K302D L1000 INDUCTOR,CHIP ELCH0001408...
  • Page 197 R1025 PCB ASSY,MAIN,PAD SHORT SAFP0000501 0OHM_1005 R1026 PCB ASSY,MAIN,PAD SHORT SAFP0000501 0OHM_1005 R1030 RES,CHIP,MAKER ERHZ0000287 47 Kohm,1/16W ,F ,1005 ,R/TP MCR01MZSF4702 R1031 PCB ASSY,MAIN,PAD SHORT SAFP0000501 0OHM_1005 R1032 RES,CHIP,MAKER ERHZ0000456 2.2 ohm,1/16W ,J ,1005 ,R/TP MCR01MZSJ2R2 R1033 PCB ASSY,MAIN,PAD SHORT SAFP0000501 0OHM_1005 R1034...
  • Page 198 R5018 RES,CHIP,MAKER ERHZ0000443 2200 ohm,1/16W ,J ,1005 ,R/TP MCR01MZSJ222 R5019 RES,CHIP,MAKER ERHZ0000486 47 Kohm,1/16W ,J ,1005 ,R/TP MCR01MZSJ473 R5020 RES,CHIP,MAKER ERHZ0000318 80.6 Kohm,1/16W ,F ,1005 ,R/TP MCR01MZSF8062 R5021 RES,CHIP,MAKER ERHZ0000286 4700 ohm,1/16W ,F ,1005 ,R/TP MCR01MZSF4701 R5022 VARISTOR SEVY0003601 5.6 V, ,SMD ,100pF, 1005 ICVL0505101V150FR R5023 RES,CHIP,MAKER...
  • Page 199 U4005 EUSY0300101 WQFN ,10 PIN,R/TP ,Small package Dual SPDT ana NLAS5223BMNR2G U4006 OSCILLATOR EXSY0024601 26 MHz,50 PPM,15 pF,SMD ,32*25*1.05 ,VX11000 OSG-310SEF U5000 EUSY0370301 VCSP50L3 ,36 ,R/TP ,ALC, AIE ,; ,IC,Charge Pump BD6088GUL U5001 EUSY0386501 uQFN10 ,10 ,R/TP ,DPDT USB 2.0 High Speed AnaloDG2722...
  • Page 200 RES,CHIP,MAKER ERHZ0000491 510 ohm,1/16W ,J ,1005 ,R/TP MCR01MZSJ511 R110 RES,CHIP,MAKER ERHZ0000491 510 ohm,1/16W ,J ,1005 ,R/TP MCR01MZSJ511 VX11000 Component List : Sensor FPCB Ref No Part Name Part Number Spec Maker P/N SPCY00 PCB,FLEXIBLE SPCY0162501 POLYI ,0.2 mm,DOUBLE , ,; , , , , , , , , ,...

Table of Contents