Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Portwell NAR-7060
Summary of Contents for Portwell NAR-7060
- Page 1 NAR-7060 Communication Appliance User′s Manual Revision: 010 Portwell Inc. 3F, No. 92, Sec. 1, Nei-Hu Rd., Taipei 114, Taiwan, R.O.C. Headquarter: +886-2-2799-2020 FAX: +886-2-2799-1010 http://www.portwell.com.tw Email: info@mail.portwell.com.tw Item NO: B8980700...
-
Page 2: Table Of Contents
2.9 Remove and Install PCI card......................... 9 2.10 Product Specifications........................10 2.11 Hardware Configuration Setting....................... 11 2.12 Install a Different Processor......................13 2.13 Connect to the console........................14 Chapter 3 Operation Guide...................15 Brief Guide of PPAP-3720........................ 15 System Architecture.......................... 16 NAR-7060 User’s Manual... -
Page 3: Chapter 1 Introduction
Chapter 1 Introduction 1.1 About This Manual This manual describes all required information for setting up and using the NAR-7060. NAR-7060 provides the essential components for delivering optimal performance and functionality in the high-end communications appliance market segment. This manual should familiarize you with NAR-7060 operations and functions. -
Page 4: Technical Support Information
1.3 Technical Support Information Users may find helpful tips or related information on Portwell's web site: http://www.portwell.com.tw. A direct contact to Portwell's technical person is also available. For further support, users may also contact Portwell’s headquarter in Taipei or your local distributors. -
Page 5: Chapter 2 Getting Started
Avoid short-circuiting the lithium battery; this can cause it to superheat and cause burns if touched. Do not operate the processor without a thermal solution. Damage to the processor can occur in seconds. Do not block air vents. Minimum 1/2-inch clearance required. NAR-7060 User’s Manual... -
Page 6: The Chassis
Fig. 2-3 Screws out from cover Fig. 2-4 Slide the cover backwards and pull the rear edge upwards. 2. The top cover ( Fig. 2-10 ) can be removed from the base stand ( Fig. 2-11 ). NAR-7060 User’s Manual... -
Page 7: Installing Or Removing A Sodimm
( Fig. 2-12, 2-13 )(slot 1 and 3 must be populated simultaneously) Fig. 2-12 The memory slot Fig. 2-13 Install DIMM 2. By pulling the arms, the DIMM can eject itself ( Fig. 2-14 ). Fig. 2-14 Eject a DIMM module NAR-7060 User’s Manual... -
Page 8: Remove And Install Cpu
6. Please be careful of the distance between the heatsink and the board, it must be 14±5% mm to avoid bending the board( Fig 2-19,Fig 2-20.Fig 2-21 ) Fig. 2-19 measure the distance between the Fig. 2-20 the distance between the heatsink heatsink and the board and the board NAR-7060 User’s Manual... -
Page 9: Remove And Install Battery
The system has an internal drive bay for two 3.5" hard disk drive. If the HDD is not pre-installed, you can install it by yourself. Follow the steps below to install the HDD: Before a HDD can be installed onto NAR-7060. 1. Remove HDD bracket ( Fig. 2-24 ) install HDD into the HDD bracket. -
Page 10: Remove And Install Pci Card
1. The PCI-X slot is located on the left of the board ( Fig. 2-29 ). 2. The back of the PCI-X card should be against the back of NAR-7060 ( Fig. 2-30, 2-31 ). Fig. 2-29 PCI-X slot on the back of PPAP- Fig. -
Page 11: Product Specifications
512MB PC1600 DDR RAM module, upgradeable to 4GB • BIOS: Award system BIOS with 512KB flash ROM • I/O Ports Three Gigabit Ethernet ports • Three 10/100 BASE-T Ethernet ports • One RS-232 system console • Two USB ports NAR-7060 User’s Manual... -
Page 12: Hardware Configuration Setting
Here NC stands for “Not Connected”. (Please refer to Fig. 2-43 for detailed jumper positions.) Jumper Setting Table (JP1-JP9) BUZZER Default Setting ★ Short ENABLE DISABLE TCO TIMER Default Setting Short ENABLE ★ DISABLE BIOS WRITE PROTECT Default Setting ★ Short WRITE ENABLE NAR-7060 User’s Manual... - Page 13 Devices are connected through these connectors which includes IDE, COM Port etc… Connector Function Remark COPPER GIGABIT COPPER GIGABIT COPPER GIGABIT 10/100M Bits RJ45 10/100M Bits RJ45 10/100M Bits RJ45 Internal PS/2 KB/MOUSE Connector D Type COM1 Connector Stack Dual USB Connector FWH Connector for Debugging NAR-7060 User’s Manual...
-
Page 14: Install A Different Processor
3. Carefully lift up the existing CPU to remove it from the socket. 4. Follow the steps of CPU installation to change to another one or place handling bar to close the opened socket. Configure Processor Speed Please into BIOS menu select Frequency/Voltage Control，change CPU Clock Ratio to20X NAR-7060 User’s Manual... -
Page 15: Connect To The Console
If users use a headless NAR-7060, which has no mouse/keyboard and VGA output connected to it, the console may be used to communicate with NAR-7060. To access NAR-7060 via the console, Hyper Terminal is one of the choices. Follow the steps below for the setup: 1. -
Page 16: Chapter 3 Operation Guide
5. Turn on the power of NAR-7060, after following screen was shown 6. You can then see the boot up information of NAR-7060 7. This is the end of this section. If the terminal did not port correctly, please check the previous steps. -
Page 17: System Architecture
The ICH3 provides a highly integrated multifunction for the best industry applications. It supports 2-channel dedicated Ultra ATA/33/66/100 IDE master interface, Universal Serial Bus (USB) controllers and one 64-bit PCI bus interface. All detailed operating relations are shown in Fig. 3-2 (PPAP-3720 System Block Diagram). NAR-7060 User’s Manual... - Page 18 HI 2.0 P64H2 #3 82559#3 SUPER I/O PCI-X CHANNEL B PMC32 PS/2 COM1/COM2 KB/MOUSE MONITOR PORTWELL Title GARNET CANYON CPU BOARD Size Document Number BLOCK DIAGRAM Date: Friday, June 21, 2002 Sheet Figure 3-2 PPAP-3720 E7500 Block Diagram NAR-7060 User’s Manual...
Need help?
Do you have a question about the NAR-7060 and is the answer not in the manual?
Questions and answers