Download Print this page
Sealey SBS260 Instructions

Sealey SBS260 Instructions

Variable speed belt sander 260w

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instructions
protection
1. SAfETy
1.1.
Electrical Safety
WARNING! it is the user's responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the sander is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
9
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
General Safety
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
WARNING! disconnect from power supply before changing accessories or servicing.
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
9
Before each use check abrasive belt for condition. If worn or damaged replace immediately.
9
use only the correct size and type of sanding belt with this sander.
9
ensure there are no flammable or combustible materials near the work area.
9
WARNING! Always wear approved eye or face and hand protection when operating the sander. use face, dust, or respiratory
protection in accordance with cosHH regulations.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the sander. never hold a work piece by hand.
9
check the work piece to ensure there are no protruding screws, bolts, nuts, nails, rivets, etc.
9
Avoid unintentional starting.
9
Keep power lead away from heat, oil and sharp edges.
9
Prolonged exposure to vibration from this sander poses a health risk. it is the owner's responsibility to correctly assess the potential
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
© Jack sealey limited
instructions for
VARIABLE SPEED BELT SANDER 260W
model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
SBS260
Wear protective
Wear ear
clothing
protection
Wear a mask
recommended fuse rating
3 Amp
sBS260 | Issue 3 05/04/17

Advertisement

loading

Summary of Contents for Sealey SBS260

  • Page 1 SBS260 model no: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 3. We recommend personal protection by using the following safety items: a) Paint Spray Respirator (Sealey ref. SSP1699) b) PE Coated Hooded Coverall (Sealey ref. SSP265-L). c) Latex Gloves (Sealey ref.SSP24). 4. Take adequate measures to contain the paint dust, flakes and scrapings.
  • Page 3 Original Language Version sBS260 | Issue 3 05/04/17 © Jack sealey limited...
  • Page 4 5. MAINTENANcE WARNING! Before performing any maintenance disconnect the sander from the power supply. ‰ 5.1. All maintenance should only be carried out by an authorised sealey service agent. 5.2. cleaning 5.2.1. Blow clean with compressed air. Always wear eye protection and dusk masks when using compressed air to clean the sander.