Screen Technics Interfit Projector Bracket Instructions

INSTRUCTIONS - INTERFIT
rojector Bracket
Thank you for purchasing a Screen Technics Interfit Projector Bracket
and please read the following instructions before attempting to install a
projector.
r purchasing a Screen Technics Interfit Projector Bracket and please read the following instructions
pting to install a projector.
In your package you will have several parts that require assembly to create a basic Flush Style
age you will have several parts that require assembly to create a basic Flush Style Interfit Projector
Interfit Projector Bracket, if you have purchased an extension post please read that section
u have purchased an extension post please read that section separately as listed below.
separately as listed below.
1. Projector Mounting Head – which has the spider arms, ball joint and
ector Mounting Head – which has the spider arms, ball joint and
threaded adjustment collar.
aded adjustment collar.
2. Central Post – which varies in length according to model purchased,
ntral Post – which varies in length according to model purchased, with
with removable threaded head ring.
ovable threaded head ring.
ing Plate - with base collar for post mounting.
3. Ceiling Plate - with base collar for post mounting.
ach the Projector Mounting Head assembly to the projector, by loosening the Allen Key (6mm) on
ylon ball joint, this in-turn loosens the Spider Arms to enable movement to locate the appropriate
STEP 1. Step 1 – Attach the Projector Mounting Head assembly to the projector, by loosening the
ounting holes.
Allen Key (6mm) on top of the nylon ball joint, this in-turn loosens the Spider Arms to enable
pplied bolts, 4 off ( M4, M5, M6 ) to secure projector to Spider Arms, being careful not to screw
movement to locate the appropriate projector mounting holes.
ar as this may "bottom out" the bolts in the threaded holes in the projector, as this could damage the
Utilise the supplied bolts, 4 off ( M4, M5, M6 ) to secure projector to Spider Arms, being careful
it.
not to screw down too far as this may "bottom out" the bolts in the threaded holes in the
projector, as this could damage the projector unit.
ller's responsibility to ensure that the supplied bolts are suitable for the fitting task and we
It is the installer' s responsibility to ensure that the supplied bolts are suitable for the fitting task
d that at least 5mm of bolt thread be utilised in fitting the projector.
and we recommend that at least 5mm of bolt thread be utilised in fitting the projector.
ate the Ball Joint assembly centrally (approx) over the spider arms, that are now attached to the
nd re-tighten the 6mm Allen Key bolt, locking the arms into position.
vement of the ball joint within the arms radius area can be utilised after the mount is attached to the
ny minor side sideways or front to back adjustment if required.
w connect the mounting post ( 6 Screws ) to the baseplate / collar assembly and secure the ceiling
o a suitable structure – never attach directly to plaster ceiling without additional support – and
Projector Bracket
AUSTRALIA
22-24 Suttor Road, Moss Vale NSW 2577
+61 2 4869 2100
STEP 2. Locate the Ball Joint assembly centrally (approx) over the spider arms, that are now
attached to the projector and re-tighten the 6mm Allen Key bolt, locking the arms into position.
NB: This movement of the ball joint within the arms radius area can be utilised after the mount
is attached to the ceiling for any minor side sideways or front to back adjustment if required.
STEP 3. Now connect the mounting post ( 6 Screws ) to the ceiling plate / collar assembly and
secure the ceiling plate to a suitable structure – never attach directly to plaster ceiling without
additional support – and decide on the best solution for cable management.
CABLE MANAGEMENT - It is possible to use the mounting post for cable runs, just unscrew
the Threaded Head Ring ( 6 screws ) and pass the cable heads through the post and
place the mid sections of the cables in the cable exist cut-out and re-attach the
Threaded Head Ring. Repeat the process if required at the ceiling plate end or simply
run the cables through the open end of the ceiling plate.
STEP 4. Now you have the ceiling plate
assembly fixed to a suitable structure, the
cable laid out as discussed above, it is now
time to attach the projector mounting head
assembly – which has the projector currently
installed upon it
– by holding it in position at the end of the
post where the threaded head ring is attached
and utilise the threaded adjustment collar to
screw the two assemblies together.
The threaded adjustment collar tightens
around a brass ball joint which will provide
adjustment for pitch and yaw when lightly
tightened, and locks into position when fully
tightened.
Please note that no real force need be applied
to the tightening of this collar, hand-tight will
be sufficient for the task.
NEW ZEALAND
44 Mahana Road, Te Rapa, Hamilton info@screentechnics.com.au
0800 022 821 screentechnics.com.au
1
Continued Over.../
ESTABLISHED IN 1990