Page 1
Use only in conjunction with the operating instructions of the folloing circulators: Heating Circulator SL-12 Refrigerated/Heating Circulator FP40-HL Refrigerated/Heating Circulator FP45-HL Ultra-Low Refrigerated Circulator FP51-SL JULABO USA, Inc. 884 Marcon Boulevard Allentown, PA 18109 Phone: +1(610) 231-0250 Fax: +1(610) 231-0260 info.us@ julabo.com www.julabo.com 19532707-V3.doc...
Page 2
Congratulations! You have made an excellent choice. JULABO thanks you for the trust you have placed in us. This operating manual has been designed to help you gain an understanding of the operation and possible applications of our Booster Heater. For optimal utilization of all functions, we recommend that you thoroughly study this manual prior to beginning operation.
1.1. Description The HST booster heater consists of two components: a 2x3 kW heater with a float switch for low level protection and a heater control. The 2x3 KW heater matches the bath openings of the JULABO model combinations and replaces the bath cover.
Page 5
Do not expose the unit to sunlight. Appropriate operation Only qualified personnel is authorized to configure, install, maintain, or repair the HST booster heater. Persons who operate the circulator must be trained in the particular tasks by qualified personnel.
Warning label W26: Colors: yellow, black Hot surface warning. (The label is put on by JULABO) 2.1. Disposal Over the long operating period of the unit, disposal rules may change. Therefore, only qualified personnel should handle the disposal. Contact an authorized waste management company in your country.
Technical specifications HST Booster Heater 6 kW SL-12 SL-12 JULABO Order No. 8810007.7 8810007.16 Heating capacity 2 x 3 2 x 3 Mains power connection 400/50/3 phases 208-230 / 50/60/ (3PNPE) 3 phases (3PPE) Current draw 3x14 (at 400 V)
Page 8
HST Booster Heater 6 kW FP45-HL FP45-HL JULABO Order No. 8810009.7 8810009.16 Heating capacity 2 x 3 2 x 3 Mains power connection V / Hz 400/50/3 phases 208-230 / 50/60/ (3PNPE) 3 phases (3PPE) Current draw 3x14 (at 400 V)
Page 9
Environmental conditions according to IEC 61 010-1: Use indoors only. Altitude up to 2000 m - normal zero. Ambient temperature: see Technical specifications Humidity: Max. relative humidity 80% for temperatures up to +31 °C, linear decrease down to 50% relative humidity at a temperature of +40 °C Max.
Use only in conjunction with the operating instructions of the circulator. • Fire hazard! Only switch on the HST when the booster heater (11) is mounted in a filled circulator bath! When filling the circulator do not allow booster module to rest on the float switch.
Page 11
• Never operate equipment with damaged mains power cables. • Some parts of the bath cover may become extremely warm during continuous operation. Therefore, exercise particular caution when touching these parts. CAUTION: Check the safety installation at least twice a year! -OFF- S -20.00 •...
Operating Controls and Functional Elements HST (control unit) 1 Mains power switch Only operates the power supply (6) for the HST Reset electronics. 2 Reset button For cancelling the alarm after the cause of the alarm has been eliminated. 3 Control light: Alarm...
Assembly Instructions WARNING: Fire hazard! Only switch on the HST when the booster heater (11) is mounted in a filled circulator bath! When filling the circulator do not allow booster module to rest on the float switch. It may be deactivated and/or damaged.
2 x 3 kW) and the circulator pump are now in use. Disconnecting the booster heater: • If no additional heating is required, the HST can be switched off at the mains power switch (1). The booster heater is then disonnected.
The booster heater is designed for continuous operation under normal conditions. Periodic maintenance is not required. The tank should be filled only with a bath fluid recommended by JULABO. To avoid contamination, it is essential to change the bath fluid from time to time. Repairs:...
10. WARRANTY PROVISIONS The following Warranty Provisions shall apply to products sold in North America by Julabo (“Seller”) to the entity shown as buyer (“Buyer”) on Seller’s invoice. Initial Warranty. Upon Seller’s receipt of payment in full for the products and subject to Buyer’s compliance with the terms of sale and any other agreement with Seller relating to the products,...
Page 18
THE REMEDIES PROVIDED IN THE INITIAL WARRANTY ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE TO THE BUYER. NOTWITHSTANDING ANYTHING TO THE CONTRARY CONTAINED HEREIN, AND EVEN IF THE SOLE AND EXCLUSIVE REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE FOR ANY REASON WHATSOEVER, IN NO EVENT SHALL SELLER BE LIABLE FOR BUYER’S MANUFACTURING COSTS, LOST PROFITS, GOODWILL, OR ANY OTHER SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY AND ALL SUCH DAMAGES ARE HEREBY DISCLAIMED.
Need help?
Do you have a question about the HST and is the answer not in the manual?
Questions and answers