Do you have a question about the Z150 and is the answer not in the manual?
Questions and answers
David Henry
March 22, 2025
left speaker not working
1 comments:
Mr. Anderson
March 22, 2025
The left speaker of the Logitech Z150 may not be working due to one of the following reasons:
1. Power Not Connected – Ensure the speakers are plugged in and powered on, indicated by the green light. 2. Cable Connection Issue – The left speaker is connected to the right speaker via an internal cable. Check if this connection is secure. 3. Audio Input Issue – Verify that the 3.5mm audio cable is properly connected to the correct port on the computer or audio device. 4. Improper Audio Splitter Use – If using a splitter, ensure both channels are correctly connected. 5. Volume Balance Settings – Check the computer’s audio settings to ensure the balance is not set fully to one side.
If these steps do not resolve the issue, the left speaker may be defective.
This answer is automatically generated
ömer erçetin
January 29, 2025
no sound from speakers .
windows 11 does not list logitech among devices
1 comments:
Mr. Anderson
February 10, 2025
The Logitech Z150 speakers may not produce sound on Windows 11 and may not appear among devices due to the following reasons:
1. Incorrect Connection: Ensure the 3.5mm audio jack is plugged into the correct port on the PC (typically the lime green "speaker out" jack).
2. Muted or Low Volume: Check if the speakers' volume is turned up and not muted.
3. Audio Output Settings: Make sure the correct playback device is selected in Windows sound settings.
4. Driver Issues: Verify that the audio drivers are installed and updated.
5. Hardware Issues: Test the speakers on another device to rule out a defect.
If the speakers do not appear in the device list, they may not be detected because they use a 3.5mm analog connection rather than USB, meaning they won’t show up as a separate device in Windows. Instead, check the default audio output device and ensure it is set to the correct sound card.
This answer is automatically generated
ömer erçetin
January 29, 2025
desktop does not recognize z150 speaker cannot get any sound from them.
1 comments:
Mr. Anderson
February 10, 2025
Your Logitech Z150 speaker may not be recognized or producing sound due to several possible reasons:
1. Connection Issue – Ensure the speaker is properly plugged into the correct audio jack on your desktop. Try using a different port, such as the rear audio output instead of the front headphone jack.
2. Hardware Issue – If only one speaker stopped working, there might be a fault in the speaker itself or the internal wiring.
3. Volume and Power – Check if the speaker is powered on, the volume is turned up, and not muted.
4. Driver Issues – Ensure your computer's audio drivers are up to date. Go to Device Manager and check if the sound device is recognized.
5. Audio Settings – Verify that the correct playback device is selected in your computer's sound settings.
6. Testing with Another Device – Try plugging the speakers into another device (like a phone or another computer) to see if they work.
If none of these steps resolve the issue, the speaker may be defective.
This answer is automatically generated
James
June 28, 2025
I have an older ASUS desktop, my original speakers stopped working. I bought the Logiteck Z150 but it does not tell you which of the 6 35mm inputs to use to install the simple speaker system. I have tried all 6, but none of them seem to be working.
KNOW YOUR PRODUCT Left speaker Right speaker 3.5 mm auxiliary input jack Headphone jack Power and volume control AC power adapter 3.5 mm auxiliary input DC power plug English...
CONNECT THE SPEAKERS 1 Connect the DC power plug to the back of your right speaker and connect your AC adapter to the electrical outlet 2A Connect your source device using the attached 3 5mm auxiliary input on the right speaker 2B You can also connect a device to the auxiliary input jack on the front of the right speaker 3 (Optional) Connect your headphones to the headphone jack on the front of the right speaker 4 Turn the speaker on using the Power/Volume knob...
ADJUST THE VOLUME 1 Increase (or decrease) the volume of speakers by rotating the single volume control knob clockwise (or counter-clockwise) on the right speaker www.logitech.com/support/Z150 English...
PRÉSENTATION DU PRODUIT Haut-parleur Haut-parleur droit gauche Prise audio auxiliaire 3,5mm Prise casque Bouton d'alimentation et de volume Adaptateur secteur Entrée auxiliaire 3,5mm Prise d'alimentation CC Français...
CONNEXION DES HAUT-PARLEURS 1 Connectez la prise d’alimentation CC à l’arrière de votre haut-parleur droit, puis connectez l’adaptateur secteur à une prise électrique 2A Connectez votre dispositif source à l'aide de l'entrée auxiliaire 3,5mm du haut-parleur droit 2B Vous pouvez également connecter un dispositif à la prise d'entrée auxiliaire à l'avant du haut- parleur droit 3 (Facultatif) Connectez votre casque à...
AJUSTEMENT DU VOLUME 1 Augmentez (ou baissez) le volume des haut-parleurs en faisant tourner le bouton de contrôle du volume dans le sens horaire (ou antihoraire) sur le haut-parleur droit www.logitech.com/support/Z150 Français...
COMPONENTES DEL PRODUCTO Altavoz izquierdo Altavoz derecho Toma de entrada auxiliar de 3,5 mm Toma de audífonos Control de encendido y volumen Adaptador de alimentación de CA Entrada auxiliar de 3,5 mm Clavija de alimentación de CC Español...
Page 10
CCONECTA LOS ALTAVOCES 1 Conecta la clavija de alimentación de CC a la parte posterior del altavoz derecho y conecta el adaptador de CA a la toma de corriente Conecta el dispositivo de origen usando la entrada auxiliar de 3,5 mm situada en el al- tavoz derecho 2B También puedes conectar un dispositivo a la toma de entrada auxiliar en la parte frontal del altavoz derecho...
Page 11
AJUSTA EL VOLUMEN 1 Aumenta (o reduce) el volumen de los altavoces girando el control de volumen en el sentido de las agujas del reloj (o en sentido contrario) en el altavoz derecho www.logitech.com/support/Z150 Español...
Page 12
CONHEÇA O SEU PRODUTO Caixa de som Caixa de som direita esquerda Entrada auxiliar de 3,5 mm Entrada para fones de ouvido Controle de volume e energia Adaptador de força CA Entrada auxiliar de 3,5 mm Plugue de alimentação CC Português...
Page 13
CONECTAR AS CAIXAS DE SOM 1 Conecte o plugue de energia CC na parte traseira da caixa de som direita e conecte o adaptador CA à tomada elétrica 2A Conecte o dispositivo de origem usando a entrada auxiliar de 3,5 mm acoplada da caixa de som direita 2B Você...
AJUSTAR O VOLUME 1 Aumente (ou diminua) o volume das caixas de som girando o único botão de controle de volume no sentido horário (ou anti-horário) na caixa de som direita www.logitech.com/support/Z150 Português...
Need help?
Do you have a question about the Z150 and is the answer not in the manual?
Questions and answers
left speaker not working
The left speaker of the Logitech Z150 may not be working due to one of the following reasons:
1. Power Not Connected – Ensure the speakers are plugged in and powered on, indicated by the green light.
2. Cable Connection Issue – The left speaker is connected to the right speaker via an internal cable. Check if this connection is secure.
3. Audio Input Issue – Verify that the 3.5mm audio cable is properly connected to the correct port on the computer or audio device.
4. Improper Audio Splitter Use – If using a splitter, ensure both channels are correctly connected.
5. Volume Balance Settings – Check the computer’s audio settings to ensure the balance is not set fully to one side.
If these steps do not resolve the issue, the left speaker may be defective.
This answer is automatically generated
no sound from speakers . windows 11 does not list logitech among devices
The Logitech Z150 speakers may not produce sound on Windows 11 and may not appear among devices due to the following reasons:
1. Incorrect Connection: Ensure the 3.5mm audio jack is plugged into the correct port on the PC (typically the lime green "speaker out" jack).
2. Muted or Low Volume: Check if the speakers' volume is turned up and not muted.
3. Audio Output Settings: Make sure the correct playback device is selected in Windows sound settings.
4. Driver Issues: Verify that the audio drivers are installed and updated.
5. Hardware Issues: Test the speakers on another device to rule out a defect.
If the speakers do not appear in the device list, they may not be detected because they use a 3.5mm analog connection rather than USB, meaning they won’t show up as a separate device in Windows. Instead, check the default audio output device and ensure it is set to the correct sound card.
This answer is automatically generated
desktop does not recognize z150 speaker cannot get any sound from them.
Your Logitech Z150 speaker may not be recognized or producing sound due to several possible reasons:
1. Connection Issue – Ensure the speaker is properly plugged into the correct audio jack on your desktop. Try using a different port, such as the rear audio output instead of the front headphone jack.
2. Hardware Issue – If only one speaker stopped working, there might be a fault in the speaker itself or the internal wiring.
3. Volume and Power – Check if the speaker is powered on, the volume is turned up, and not muted.
4. Driver Issues – Ensure your computer's audio drivers are up to date. Go to Device Manager and check if the sound device is recognized.
5. Audio Settings – Verify that the correct playback device is selected in your computer's sound settings.
6. Testing with Another Device – Try plugging the speakers into another device (like a phone or another computer) to see if they work.
If none of these steps resolve the issue, the speaker may be defective.
This answer is automatically generated
I have an older ASUS desktop, my original speakers stopped working. I bought the Logiteck Z150 but it does not tell you which of the 6 35mm inputs to use to install the simple speaker system. I have tried all 6, but none of them seem to be working.