Advertisement
Quick Links
General assembly drawing for
BELITEC foldaway beds
Singlebed
with integrated side cladding and
front plate
80, 90, 100, 120, 140, 150 cm
width
60 cm
cabinet depth
Rev:
Novembre 12 2018
Please
destroy older
assembly drawings!
We do not assume any liability in cases of non-adherence to the assembly manual.
- We reserve the right to make modifications -
The statutory warranty period applies!
D:\montage\montageanleitungen\englisch\2018\eb-eng_11-2018.pub
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hartmann BELITEC
Summary of Contents for Hartmann BELITEC
- Page 1 General assembly drawing for BELITEC foldaway beds Singlebed with integrated side cladding and front plate 80, 90, 100, 120, 140, 150 cm width 60 cm cabinet depth Rev: Novembre 12 2018 Please destroy older assembly drawings! We do not assume any liability in cases of non-adherence to the assembly manual.
-
Page 2: Safety Instructions
Only allow expert personnel who have received the required instruction to assemble the BELITEC system! Safety instructions This device can be used by children aged 8 and older or persons with reduced physical, sensory or mental abilities or lack of experience and knowledge, provided they are supervised or have been informed how to use the device in a safe manner and understand the resulting risks! Ensure that children cannot play with the device. -
Page 3: Parts List
Parts list - 1 set of bend guides A LH and RH - 2 x 2 guide rails - 1 set of bend guides B LH and RH - 8 ventilation rings - 1 carriage unit + drawer + side cladding - 1 metal feet with rollers for the front plate - 1 chain frame + 4 screws - 2 belts... - Page 4 chain guide (*) The electrical system of controls and drives consists of five components. Plug the main electrical connection (1) into the control block (2). Then plug the block for emergency lowering (3a) into the control block and connect the switch (3b) with housing.
- Page 5 side view front view chain outlet foldaway internal dimension bed system X (mm) min. 280 mm 1196 1396 1496 component E component F...
- Page 6 Electrical lines should only be installed by qualified personnel. Liability disclaimer We would like to point out that Hartmann asytec GmbH & Co. KG will not assume any liability for injuries, material damage or other damage caused by failure to adhere to this assembly manual.
- Page 7 Elimina ng malfunc ons of the foldaway bed control Possible malfunction Solution The foldaway bed no longer responds after moving for 2 min. Disconnect the controls from the mains for approx. 5 sec Controls do not respond to use of the hand switch Disconnect the controls from the mains for approx.
- Page 8 Note: For systems with internal doors, the side walls must be doubled accordingly to ensure that the depth dimension of 600 mm is maintained! Assembly instructions Read carefully, adhere to specified dimensions, note the RH / LH side, route cable precisely, install the controls and the corresponding receiver so that they are freely accessible! Recommendation:...
- Page 9 Install component A. Leave a gap of minimum 50 mm in the cabinet lid area and ensure that the chain outlet is sufficient. Pay attention to cabinet lighting cables etc., increase dimension, if necessary. Ensure that the gap between component A and the rear of the cabinet storage space is no more than 10 mm.
- Page 10 Install the drive housing (SB - drive 1.1) with the chain guide (*) and SB - drive 1.1 the yellow mark on the RH, the other drive housing on the RH side wall. SB - drive 1.2 Leave off the screws intended for the stops..
- Page 11 Fit part E. Produce the spar for fastening the belts from a flexural resistant material such as laminated wood (manufactured by a skilled cabinet builder) with a min. cross section of 95 x 20 mm. The length is depending on dimension X (drawing figure) less 8 mm.
- Page 12 Connect the protruding hexagonal rods of the drives to the synchronous shaft (SB - SA) by pushing the couplings (SB - KU) up to the marking. If the hexagonal rods are not in the same position, disconnect a drive from the control system.
- Page 13 To retract the system use the drives pushing both buttons A + B on the hand-held switch at the same time until 3/4th of the total length of the chain frame has been drawn in. Ensure that both chain ends are pulled in uniformly. During this assembly step, the chain can only be extended using the button of the emergency lowering.
- Page 14 Fit the stops for retracting/extending on the LH and RH side and the centre support. Prepare the belt loops. Fasten the metal hook on the spars. Attach the belt holder on component E.
- Page 15 The first run of the system is intended for adjusting the electronic controls, is carried out at reduced speed and is called the teaching run. The hand-held switch is used for drawing in the chain. Push the buttons A + B at the same time and hold. The drives retract the system and stop at the end position.
- Page 16 Fit the front plate to the pushed-in drawer. Ensure that there is a gap of minimum 15 mm between the fastened panel and the floor. Ensure that the front plate width of the system equals the internal dimension plus double the side wall thickness.
- Page 17 This must be made by the cabinet manufacturer. Alfred-Nobel-Straße 9 32584 Loehne - Germany Tel.: +49 57 32 - 99 22 60 Fax: +49 57 32 - 99 22 61 internet: www.belitec.de e-mail: belitec@hartmann-asytec.de Rev: Novembre 12 2018 Pease destroy older assembly drawings! We do not assume any liability in cases of non-adherence to the assembly manual.
Need help?
Do you have a question about the BELITEC and is the answer not in the manual?
Questions and answers