Advertisement
Quick Links
General assembly drawing for
BELITEC foldaway beds
Sofa bed
with integrated side cladding and
front plate
80, 90, 100, 120, 140, 150 cm
width
60 cm
cabinet depth
Rev:
June 26 2018
Please
destroy older
assembly drawings!
We do not assume any liability in cases of non-adherence to the assembly manual.
- We reserve the right to make modifications -
The statutory warranty period applies!
D:\montage\montageanleitungen\englisch\2018\qs-eng_26-2018.pub
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hartmann BELITEC
Summary of Contents for Hartmann BELITEC
- Page 1 General assembly drawing for BELITEC foldaway beds Sofa bed with integrated side cladding and front plate 80, 90, 100, 120, 140, 150 cm width 60 cm cabinet depth Rev: June 26 2018 Please destroy older assembly drawings! We do not assume any liability in cases of non-adherence to the assembly manual.
-
Page 2: Safety Instructions
Only allow expert personnel who have received the required instruction to assemble the BELITEC system! Safety instructions Do not allow persons (including children) with impaired physical, sensory or mental abilities or a lack of experience and / or knowledge to access the operating elements of the electrical drive! Ensure that children cannot play with the device. -
Page 3: Parts List
Parts list - 2 sets of cam guides A LH and RH - 4 x 2 guide rails - 1 set of cam guides B LH and RH - 16 air ventilation rings - 1 set of cam guides C LH and RH - 2 metal feets with rollers for front plate - 2 carriage units + drawers + side claddings - 4 belts... - Page 4 chain guide (*) The electrical system of controls and drives consists of five components. Plug the main electrical connection (1) into the control block (2). Then plug the block for emergency lowering (3a) into the control block and connect the switch (3b) with housing.
- Page 5 side view (RH / LH side wall) front view chain outlet foldaway bed system internal dimension X (mm) 200 = 2 x 100 2 x 996 min. mattress width unit height Y (mm) 280 mm 1350 1350 1350 1550 1750 1850 component E component F...
- Page 6 Manufacture the centre support according to the drawing, accurately fitting the bend guides. If necessary the data required for CNC machining can be supplied. component A centre support * Length dependent on mattress width component C component B component C component B without edge with edge...
- Page 7 Note: For systems with internal doors, the side walls must be doubled accordingly to ensure that the depth dimension of 600 mm is maintained! Assembly instructions Read carefully, adhere to specified dimensions, note the RH / LH side, route cable precisely, install the controls and the corresponding receiver so that they are freely accessible! Recommendation:...
- Page 8 Install component A. Leave a gap of minimum 50 mm in the cabinet lid area and ensure that the chain outlet is sufficient. Pay attention to cabinet lighting cables etc., increase dimension, if necessary. Ensure that the gap between component A and the rear of the cabinet storage space is no more than 10 mm.
- Page 9 5.5. Fit the actuator housing with yellow mark to the RH side panel and the other housing to the RH side panel in the recesses provided. Attach the actuator housings without motor to the centre support. Leave off the screws intended for the stops. centre support...
- Page 10 Attach component E. Ensure that the cabinet maker has made the spar for fastening the belts (component E) of material with high bending strength, e.g. laminated wood and that it has a cross section of 95 x 20 mm. The length is the internal dimension minus 8 mm. Always note the exact internal dimension! Connect the electrical system, this means control system + emergency lowering + actuators.
- Page 11 Connect the protruding hexagonal rods of the drives to the synchronous shaft (SB - SA) by pushing the couplings (SB - KU) up to the marking. Roll out the chain frame and then manually push it in up to the gear wheel of the drive. Ensure that both chain ends are in the same position when making contact.
- Page 12 To retract the system use the drives pushing both buttons A + B on the hand-held switch at the same time until 3/4th of the total length of the chain frame has been drawn in. Ensure that both chain ends are pulled in uniformly. During this assembly step, the chain can only be extended using the button of the emergency lowering.
- Page 13 Fit the stops for retracting/extending on the LH and RH side and the centre support. Prepare the belt loops. Fasten the metal hook on the spars. Attach the belt holder on component E.
- Page 14 The first run of the system is intended for adjusting the electronic controls, is carried out at reduced speed and is called the teach-in run. The hand-held switch is used for drawing in the chain. Push the buttons A + B at the same time and hold. The drives retract the system and stop at the end position.
- Page 15 Fit the metal foot to the front plate. Fit the front plate to the pushed-in drawer. Ensure that there is a gap of minimum 15 mm between the fastened panel and the floor. Ensure that the front plate width of the system equals the internal dimension plus double the side wall thickness.
- Page 16 Lay the mattress on the chain frame. Pay attention to the correct position of the mattress, especially the front edge. The front part of the mattress contains a softer insert. Mattress front = 25 mm distance from the 1st loop. For reasons of appearance, a cover strip can be fitted to the mattress support board.
Need help?
Do you have a question about the BELITEC and is the answer not in the manual?
Questions and answers
How to pair remote control to the receiver ? Bed doesnot response to remotes commands