Weed Eater 173487 Owner's Manual page 12

The operation of any tractor can result in foreign objects thrown into the
eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend a wide vision safety mask over
spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator to
leave the seat without first setting the
parking brake will shut off the engine.
• Depress clutch/brake pedal into full
"BRAKE" position and hold.
• Place parking brake lever in "EN-
GAGED" position and release pres-
sure from clutch/brake pedal. Pedal
should remain in "BRAKE" position.
Make sure parking brake will hold
tractor secure.
Attachment Clutch Lever
"Engaged" Position
Throttle/Choke
Control
"Disengaged"
Clutch/
Position
Brake
Pedal
Parking
Brake
"Engaged"
Position
Gearshift
Lever
"Brake"
"Disengaged"
Position Position
STOPPING
MOWER BLADES -
• To stop mower blades,move attach-
ment clutch lever to "DISENGAGED"
position.
GROUND DRIVE -
• To stop ground drive, depress clutch/
brake pedal into full "BRAKE" position.
• Move gearshift lever to neutral (N)
position.
ENGINE -
• Move throttle control to slow position.
NOTE: Failure to move throttle control to
slow position and allowing engine to idle
before stopping may cause engine to
"backfire".
• Turn ignition key to "OFF" position and
remove key. Always remove key when
leaving tractor to prevent unauthorized
use.
• Never use choke to stop engine.
IMPORTANT: Leaving the ignition
switch in any position other than "OFF"
will cause the battery to be discharged,
(dead).
NOTE: Under certain conditions when
tractor is standing idle with the engine
running, hot engine exhaust gases may
cause "browning" of grass. To eliminate
this possibility, always stop engine when
stopping tractor on grass areas.
CAUTION: Always stop tractor
completely, as described above, before
leaving the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL
Always operate engine at full throttle.
• Operating engine at less than full
throttle reduces the battery charging
rate.
• Full throttle offers the best bagging
and mower performance.
TO MOVE FORWARD AND
BACKWARD
The direction and speed of movement is
controlled by the gearshift lever.
• Start tractor with clutch/brake pedal
depressed and gearshift lever in
neutral (N) position.
• Move gearshift lever to desired
position.
• Slowly release clutch/brake pedal to
start movement.
IMPORTANT: Bring tractor to a complete
stop before shifting or changing gears.
Failure to do so will shorten the useful
life of your transaxle.
12
TRACTOR -- MODEL NUMBER 259723
STEERING
KEY PART
NO. NO.
1 140044
2 154427
3 156483
4 157473
5 6266H
6 121748X
7 19272016
8 12000029
9 3366R
10 169832
11 10040600
13 136518
15 145212
17 156546
18 57079
19 160395
22 165857
23 165851
25 154406
26 126847X
27 136874
28 19131416
29 17060612
30 76020412
32 130465
36 155099
37 152927
38 140045
39 19133812
40 7810H
41 100711L
42 145054X428
43 121749X
44 153720
46 121232X
47 6855M
51 73800500
54 74780520
62 167902
63 74780616
65 160367
66 154404
67 72140618
68 169827
79 19132012
80 74950612
82 169835
85 133835
NOTE: All component dimensions given in U. S.
inches 1 inch = 25/4 mm
DESCRIPTION
Steering Wheel
Front Axle Asm
Spindle Asm Lh
Spindle Asm Rh
Washer Thrust .75 x 1.230
Washer 25/32 x 1-5/8 x 16 Ga.
Washer 27/32 x 1-1/4 x 16 Ga.
RingKlip #T5304-75
Bearing Col Strg Blk
Draglink
Washer Lock Hvy Hlcl Spr 3/8
Spacer Brg Axle Front
Nut Hexflange Lock
Shaft Asm Strg
Washer Thrust .515 x .750 x .033
Support Shaft
Screw Hex Wsh Hd Torx
Shaft Asm Pitman
Bracket Steering
Bushing LInk Drag Blk LR
Gear Sector 22 Teeth
Washer 13/32 x 7/8 x 16 Ga.
Screw 3/8-16 x 3/4
Pin
Rod Tie Wire Form 19.75 Mech
Bushing Strg. 5/8 ID Dash
Screw
Insert, Steering Wheel
Washer 13/32 x 2-3/8 x 12 Ga.
Nut Lock Center 3/8-24
Adaptor Wheel Strg.
Boot Steering Dash P/L MTL Blk
Washer 25/32 x 1-1/4 x 16 Ga.
Extension Steering Non-adjust
Cap Spindle Fr Top Blk
Fitting Grease
Nut Lock Hx W/Ins 5/16-18unc
Bolt Fin Hex 5/16-18unc
Steering Assembly
Bolt Fin Hex 3/8-16unc x 1 Gr. 5
Spacer Axle
Bearing Arm Pittman
Bolt Rdhd Sqnk 3/8-16 x 2-1/4
Brace Axle
Washer 13/32 x 1-1/4 x 12 Ga
Bolt Hex Nylon 3/8-16 x 3/4
Bracket Susp Chasis Front
Fastner Christmas Tree
37