Related Manuals for Patriot Helicopter Tanks Series
Summary of Contents for Patriot Helicopter Tanks Series
- Page 1 Helicopter Tanks Owner’s Manual Manufactured by Minden Machine Shop Inc. 1302 K Road Minden NE 68959 1-800 264-6587 Helicopter Tank Serial # ______________ Date of Purchase _______________...
-
Page 2: Table Of Contents
Table Of Contents Safety and Operation Rules Safety Alert Symbol Safety Equipment Safety Procedures Lighting and Marking Operator Qualifications Safety Overview Safety Affirmation Sign Off Sheet Machine Inspection Safety Decals Introduction General Information Before Operation During Operation Following Operation Highway and Transport Performance Maintenance Torque Data Helicopter Tank Mounting... -
Page 3: Safety And Operation Rules
This unit was designed for specific applications. It should not be modified and/or used for any application other than which it was designed. If there are any questions regarding its application, write or call Patriot Equipment. Do not use this unit until you have been advised. For more information, call 1-800-264-6587. -
Page 4: Safety Alert Symbol
Tanks. Forklifts with too little capacity may tip towards the front where the lifted weight is. Do not use makeshift systems to handle equipment as you may create an unsafe condition. Do not attempt to raise the Patriot Helicopter Tank units by hoist or forklift when it is loaded with product. -
Page 5: Lighting And Marking
Helicopter Tanks. SAFETY OVERVIEW YOU are responsible for SAFE operation and maintenance of your Patriot Helicopter Tanks. YOU must ensure that you and anyone who is operates, maintains, or works around the Helicopter Tanks must be familiar with the operating, maintenance, and safety information contained in the manual. This manual will take you step by step through your working day and alerts you to all good safety practices while operating the tanks. -
Page 6: Safety Affirmation
I have read and understand the operator’s manual and all safety signs before operation, maintenance, or adjusting the Helicopter Tanks. I will allow only trained persons to operate the Patriot Helicopter Tanks. *An untrained operator is not qualified to operate this equipment. -
Page 7: Machine Inspection
MACHINE INSPECTION After delivery of your new Helicopter Tanks and/or completion of assembly and before each use, inspection of the equipment is mandatory. This inspection should include, but not be limited to: Check to see that all guards are in place, secure, and functional. Are the fasteners tight? Any leaks? Do the valves operate correctly? - Page 8 Safety Decal Location TS3000 The Safety Decals are located on the left side of the TS3002 saddle and on the lower cross piece as shown. The decals will face towards the outside so they can be seen by the user. The locations are the same for the front mount saddles.
-
Page 9: Introduction
INTRODUCTION Model: Helicopter Tanks Thank you for purchasing Minden Machine Shop Inc’s Helicopter tanks. We feel you have made a wise choice and hope you are completely satisfied with your Helicopter tanks. If you have any questions regarding the applications of certain solutions or chemicals, contact your chemical supplier and follow chemical manufacturer recommendations as well as all licensing and use restrictions or regulations. -
Page 10: During Operation
Use a tractor equipped with a Roll-Over Protection System (ROPS) and fasten your seat belt prior to starting the engine. Manufacturer does not recommend usage of tractor with ROPS removed. Move tractor wheels to widest recommended settings to increase stability. 10. -
Page 11: Following Operation
FOLLOWING OPERATION Rinse and clean the Helicopter Tanks when finished using them. Properly dispose of any contaminated rinse water. Following operation, or when unhitching, stop tractor or towing unit, set brakes, disengage PTO and all power drives, shut off engine and remove ignition key. ... -
Page 12: Performance Maintenance
PERFORMANCE MAINTENANCE Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. Make sure there is plenty of ventilation. Never operate engine in a closed building. Exhaust fumes may cause asphyxiation. Before working on this machine, stop vehicle, set brakes, disengage PTO and all power drives, shut off engine, and remove ignition key ... - Page 13 Helicopter Tank Assembly Instructions Helicopter Tanks...
-
Page 14: Torque Data
Torque Data for Standard Nuts, Bolts, and Capscrews Tighten all bolts to torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt chart as guide. Replace hardware with some grade bolt. Note: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout assembly of equipment. Bolt Torque for Standard Bolts Grade 2 Grade 5... -
Page 15: Helicopter Tank Mounting
Helicopter Tank Mounting Completely Assembled The Helicopter tanks come in numerous configurations, so the installation instructions will cover a broad range of tractor makes and models. Generally, the installation will be similar for all tractor makes and models. To begin, mount the side plates of the Helicopter Tanks to the frame of the tractor. -
Page 16: Helicopter Tank Mounting "Z" Bar
Helicopter Tank Mounting - "Z" Bar The Helicopter tanks come in numerous configurations, so the installation instructions will cover a broad range of tractor makes and models. Generally, the installation will be similar for all tractor makes and models. These directions are for the "Z "... -
Page 17: Front Mount Tank Mounting Bolster Type
Front Mount Tank Mounting - Bolster Type The front mount tanks come in numerous configurations, so the installation instructions will cover a broade range of tractor makes and models. Generally, the installation procedure will be similar for all tractor makes and models. Remove the front tractor weights from the mounting bolster. -
Page 18: Front Mount Tank Mounting Nose Type
Front Mount Tank Mounting - Nose Mount Type The front mount tanks come in numerous configurations, so the installation instructions will cover a broad range of tractor brands and models. Generally, the installation procedure will be similar for all tractor makes and models. Remove the front tractor weights from the mounting bolster. -
Page 19: Limited Warranty
Minden Machine Shop Inc LIMITED WARRANTY Minden Machine Shop Inc warrants all products manufactured by it to be free of defect in material and workmanship for a period of one (1) year from the date of purchase. This Minden Machine Shop Inc. warranty does not cover: Parts and accessories supplied by Minden Machine Shop Inc. -
Page 20: Warranty Registration
WARRANTY REGISTRATION To register equipment, or file a claim, copy and paste the words on this page into an email or word document, fill out the appropriate information completely, and email it to larry@mindenmachine.com with the subject as EQUIPMENT WARRANTY, or fill it out and fax it to 308-832-1340.