Advertisement
INSTALLATION INSTRUCTIONS
WARNING:
INSTALL PRODUCT IN ACCORDANCE
WITH LOCAL AND NATIONAL ELECTRICAL
CODES.
RESULT IN DEATH OR SERIOUS INJURY
ISOMETRIC VIEW
MOUNTING DIMENSIONS
DIM. 'A'
DIM. 'A'
2-1/8"
2-1/8"
(4x) Slots for 1/4-20
mounting fasteners
(by others)
WIRING DETAILS
REMOTE POWER
To Fixture
Power - Black
Power + Red
DC In
DMX APPLICATIONS RE UIRE
ONE OF THE FOLLOWING CABLES
STANDARD DMX APPLICATIONS
INDOOR
BELDEN 9841
PLENUM RATED
BELDEN 82841
BELDEN 3105A
OUTDOOR
1
PREPARE MOUNTING ARMS
Slide canopies down mounting arms away from mounting plate.
4
ATTACH START LUMINAIRE
NOTE
Hand tighten screws to
15in. lbs. Torque,
Max.
Slide start luminaire knob into mounting arms on both sides.
Secure start luminaire to mounting arms using (4x) set screws
(provided).
Insight Lighting
Phone: (505)345-0888
*Insight Lighting reserves the right to make changes to this product and related installation instructions at any time without prior notice.
MEDLEY X
WARNING:
FAILURE TO COMPLY WITH THE
READ ALL SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS MAY
INCLUDED WITH LUMINAIRE BEFORE
MOUNTING OPTIONS
DIM. 'A'
NOMINAL
FIXTURE LENGTH
12"
24"
36"
48"
REMOTE DAT/DIM
To Fixture
Power - Black
Power + Red
DC In
DC Out
Data In
GREEN/
BLACK
RED
PURPLE
POWER -
POWER +
DATA +
EXTENDED ARM MOUNT INSTALL
2
INSTALL MOUNTING ARMS
Install mounting brackets to mounting surface using (4x) 1/4-20
mounting fasteners per mounting bracket (by others) (See
'Mounting Dimensions' above). Mount power feed arms over
j-box (by others).
5
FEED WIRES-MID/END LUMINAIRES
Raise mid/end luminaire up to mounting arm. Feed wires from
mid/end luminaire through knuckle and mounting arm into j-box.
Repeat step for all mid luminaires.
Fax: (505)345-3838
WARNING:
THIS IS AN ELECTRONIC DEVICE. CARE MUST BE TAKEN
DURING STORAGE AND HANDLING. STORE IN A CLEAN, COOL
AND DRY LOCATION. ELECTROSTATIC DISCHARGE (ESD) CAN
HARM THIS PRODUCT. AVOID STATIC DISCHARGE WHILE
INSTALLING LUMINAIRE.
PACKAGE INCLUDES:
Luminaire
Assemblies
DIM. 'A'
Start/End
15-7/8"
Mounting Arm
27-7/8"
39-7/8"
51-7/8"
(2x per start/end mounting arm,
4x per mid mounting arm)
REMOTE TERMINATOR INSTALLATION
To Fixture
Data + Green/
Power - Black
Purple
Power + Red
Data - Blue/Gray
DC Out
DC In
Data In
Data Out
BLUE/
BLACK
RED
GRAY
RED
POWER +
DATA -
CHANNEL
Web: www.insightlighting.com
EAM-EXTENDED ARM
MULTIPLE MOUNT
UP & DOWNLIGHT
CONFIGURATIONS
CAUTION:
HANDLING THIS PRODUCT.
ITEMS NEEDED (SUPPLIED BY OTHERS):
Start Luminaire
Mid Luminaire
(If applicable)
Recessed J-Box
End Luminaire
(4x)1/4-20 Mounting
Mid Mounting
Arm
Set Screws
1/4" Allen Drive
Power + Black
Data + Green
Red Channel
Data - Blue
DMX Terminator
must be installed
DC In
on the Data Line
in the j-box of the
Data In
last fixture of each
run
GREEN
BLUE
WHITE
GREEN
BLUE
WHITE
CHANNEL
CHANNEL
CHANNEL
3
FEED WIRES-START LUMINAIRE
Raise start luminaire up to mounting arm. Feed wires from start
luminaire through knuckle and mounting arm into j-box.
6
ATTACH MID/END LUMINAIRE
Slide mid/end luminaire knob into mounting arms on both sides.
Secure mid/end luminaire to mounting arms using (4x) set
screws (provided). Repeat till all luminaires are mounted.
WHITE & STATIC
REMOTE
COLOR
MULTIPLE
ACTIVE WHITE
COLOR CHANGING
CAUTION:
INSIGHT LIGHTING IS NOT RESPONSIBLE FOR THE
STRUCTURAL INTEGRITY OF THE BUILDING TO
SUPPORT THE LUMINAIRE. ADDITIONAL BACKING
MAY BE REQUIRED.
Power/Data Leads
Assorted Wire
Fasteners
Nuts
Phillips Head
Screwdriver
REMOTE RGB
To Fixture
Green Channel
Blue Channel
DC Out
Data Out
PAGE 1 OF 1
IS11208-1.DWG 06MAR19 JW
REV N/C
Advertisement
