Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
INSTRUCTION MANUAL
Goboservice by Sunland Optics SRL
Via Vecchia Provinciale 167
Vecchia Provinciale 167 – Archi – 89121 Reggio Calabria (RC)
+39 0965 813264
Via Lombardia 269, 20861 Brugherio (MB)
Via Lombardia 269, 20861 Brugherio (MB)
+39 02 23166538
www.goboservice.com
info@goboservice.com
89121 Reggio Calabria (RC)
ENGLISH
Advertisement
Table of Contents
Related Manuals for Goboservice GOLUX 600
Summary of Contents for Goboservice GOLUX 600
- Page 1 ENGLISH INSTRUCTION MANUAL INSTRUCTION MANUAL Goboservice by Sunland Optics SRL Via Vecchia Provinciale 167 Vecchia Provinciale 167 – Archi – 89121 Reggio Calabria (RC) 89121 Reggio Calabria (RC) +39 0965 813264 Via Lombardia 269, 20861 Brugherio (MB) Via Lombardia 269, 20861 Brugherio (MB) +39 02 23166538 www.goboservice.com...
- Page 3 The Goboservice by Sunland Optics SRL company disclaims all liability for damage to the projector or to other property or persons deriving from installation, use and maintenance that is not carried out in accordance with that reported in this instruction manual, which must always accompany the unit.
-
Page 4: Table Of Contents
4.3. SIZING AND FOCUSING THE PROJECTED ......................13 4.4. CONTROL PANEL ..............................14 5. THECNICAL DATA ................................16 6. POSSIBLE PROBLEMS CAUSES AND SOLUTIONS ....................17 7. DIRECTIVES ..................................17 8. DISPOSAL .................................... 17 9. WARRANTY ..................................18 10. MAINTENANCE HISTORY ............................. 19 - 4 - WWW.GOBOSERVICE.COM... -
Page 5: Safety Informations
1. SAFETY INFORMATIONS Please, read carefully the following safety instructions before do any operations. The product describes in this instructions manual is a lighting fixture for the projection of a light beam. It is used usually to light, with an high level of surface brightness, big areas on which to project decorative effects or fascinating and special logos and images. - Page 6 In case of abnormalities of the case or breakage of the packaging that contains bright spare parts, do not turn on the projector and stop the use of the product. Do notinstall in - 6 - WWW.GOBOSERVICE.COM...
-
Page 7: Package Content
areasavailable to minors or persons who should be affected by the correct or wrong use of the product. The device, if it is not connected to main supply, is not dangerous for people and animals even if exposed to the rain. The projector works with electrical energy at low voltage and that puts it in an area of dangerousness typical of a household appliance;... -
Page 8: Projector Installation
ELEMENT 3is a switch that can enable / disable the power supply of the internal accessories (gobo rotation, rotation dynamic effect, etc.). ELEMENT 4 is a control panel of the main functions of the projectors. Fig.2 - 8 - WWW.GOBOSERVICE.COM... -
Page 9: Lamp Mounting Or Substitution
3.3. LENS MOUNTING or SUBSTITUTION For the lamp mounting/substitution is needed to act on the panel that is located at the back side of the main part of the projector. Provide yourself with a cloth in order to mount the lamp in a proper and functional way. -
Page 10: Gobo Mounting Instructions
For GOLUX1000 Projector the gobos must have : OD = 37,5mm and ID = 35mm. In the case of gobo with special graphics features contact = 35mm. In the case of gobo with special graphics features contact customer service Goboservice (info@goboservice.com) that will point customer service Goboservice (info@goboservice.com) that will point Fig.7 you in the best configuration. -
Page 11: Put In Function Dynamic Effect
ATTENTION: gobo mounting has to be done taking care that the gobo surface will be not touched, fouled or stained in order to avoid scratches visible on projection; these scratches then, with the heat of projector usage, can also cause the gobo breaking. The gobo mounting/substitution must be done when the projector is switched off and not connected to the mains supply. -
Page 12: Accessories Power Supply
(see Figure 16), put the projector in the desired direction and tighten the bolts again. Fig.16 - 12 - WWW.GOBOSERVICE.COM... -
Page 13: Sizing And Focusing The Projected
CAUTION: Never turn the projector down so that it moves in contact with the support surface. (see Fig.17) Always refer to the minimum distance from illuminated objects (5m). If necessary, you can use the "Extensible Stand" accessory. Fig.17 4.3. SIZING AND FOCUSING THE PROJECTED The focus of the image must be done by acting on the kit of zoom lenses installed on the projector (Fig 18);... -
Page 14: Control Panel
C.MEM* Reset (life and Confirm reset during 1 second power lamp) to confirm Mon.b. P. out xxxx r.xxx Monitoring Rated Power ballast Power value Change in val. snapshot nominal V.out xxxx Rated Tension Voltage value snapshot - 14 - WWW.GOBOSERVICE.COM... - Page 15 I. out xxxx I. out Current nominal Corrente Current value nominale snapshot t.PFC xxxx M.P.xx Temperature PFC Instantaneous MaxTemperature value Temperature t.dCd xxxx M.d.xx Temperature DC/DC Instantaneous MaxTemperature value DC/DC Temperature DC/DC Id.dr Selezione PushENTER Display and N° Identification To confirm Exchange Remote ID Ad.dM Address...
-
Page 16: Thecnical Data
Dimension gobo OD: 37,5 mm ID: 35,0 mm Possible optical 56mm/100mm/Zoom 7,70°-34° OPTIONAL ACCESSORIES Gobo holder with rotation Dynamic effect Kit change Image 5 Gobo [OD:43,2mm – ID:35,0mm] Shaper Stand extensible Stirrup Palo, Muro Rain cover - 16 - WWW.GOBOSERVICE.COM... -
Page 17: Possible Problems Causes And Solutions
6. POSSIBLE PROBLEMS CAUSES AND SOLUTIONS POSSIBLE PROBLEMS CAUSES AND SOLUTIONS ABNORMALITIES POSSIBLE CAUSES CONTROL AND SOLUTIONS CONTROL AND SOLUTIONS The projector does not turn on No power Ensure that the power supply is present Ensure that the power supply is present The projector turns on but does not emit any Lamp exhausted or burned out Lamp Replacement... -
Page 18: Warranty
Dismantling (including partial) of projector that is not made by the manufacturer will void the warranty. Consumables (such as lamp and fuse) are not covered by the warranty. Manufacturer reserves the right to modify the content of this manual at any time and without notice. - 18 - WWW.GOBOSERVICE.COM... -
Page 19: Maintenance History
10. MAINTENANCE HISTORY Projector Mod.: Date of purchase: Serial Number: Date of first power on: LAMP SUBSTITUTION DATE BRAND MODEL LIFE SUPPLIED ACCESSORIES - 19 - GOLUX600... - Page 20 NOTE - 20 - WWW.GOBOSERVICE.COM...
- Page 21 Goboservice by Sunland Optics SRL Via Vecchia Provinciale 167 Vecchia Provinciale 167 – Archi – 89121 Reggio Calabria (RC) 89121 Reggio Calabria (RC) +39 0965 813264 Via 2 Giugno19/10 Via 2 Giugno19/10 – Bonate – 24040 (BG) +39 0350176860 www.goboservice.com info@goboservice.com...
Need help?
Do you have a question about the GOLUX 600 and is the answer not in the manual?
Questions and answers