Related Manuals for Hanwha Techwin Wisenet XNV-9082R
Summary of Contents for Hanwha Techwin Wisenet XNV-9082R
- Page 1 NETWORK CAMERA User Manual XNV-9082R/XNV-8082R XND-9082RV/XND-8082RV XND-9082RF/XND-8082RF XNO-9082R/XNO-8082R XNB-9002/XNB-8002...
- Page 2 Network Camera User Manual Copyright ©2020 Co., Ltd. All rights reserved. Hanwha Techwin Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
- Page 3 overview IMPORTANT SAFETY INSTRUCTIONS 22. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface. 1.
- Page 4 overview Class construction Please read the following recommended safety precautions carefully. y Do not place this apparatus on an uneven surface. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. y Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
-
Page 5: Table Of Contents
CONTENTS OVERVIEW BOX CAMERA Important Safety Instructions What’s Included Recommended PC Specifications At a Glance Recommended Micro SD/SDHC/SDXC Mounting the Lens Memory Card Specifications Inserting/Removing a Micro SD card NAS recommended specs Optional Accessories for Installation INSTALLATION & CONNECTION Adjusting the monitoring direction for the OUTDOOR VANDAL DOME CAMERA camera What’s Included... -
Page 6: Overview
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS • CPU : Intel(R) Core(TM) i7 3.4 GHz or higher • Recommended capacity : 200GB or higher is recommended. • RAM : 8G or higher • For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products : QNAP NAS, Synology NAS •... - Page 7 Outdoor Vandal Dome Camera Indoor Dome Camera Flush Mount Dome Camera XNV-9082R/XNV-8082R XND-9082RV/XND-8082RV XND-9082RF/XND-8082RF Outdoor Bullet Camera Box Camera XNO-9082R/XNO-8082R XNB-9002/XNB-8002 English _7...
-
Page 8: Optional Accessories For Installation
overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available. Model name Hanging Mount Pole Mount Skin Cover Housing SBP-300LMW (Parapet Mount) XNV-9082R/XNV-8082R SBP-187HMW SBC-180B (Black) SBP-300CMW (Ceiling Mount) SBP-300WMW (Wall Mount) SBP-300WMW1 (Wall Mount) SBP-300NBW (Instalation Box) XND-9082RV/XND-8082RV SBP-167HMW SBC-160B (Black) -
Page 9: Outdoor Vandal Dome Camera
outdoor vandal dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Mount-plate Camera-case Camera-module Dome-cover <XNV-9082R/XNV-8082R> Pipe-cover IR LED Reset button Illumination Sensor Zoom/Focus Control Button Network Port Options (not included) Micro USB port Power port Audio/Alarm... -
Page 10: Installation
outdoor vandal dome camera INSTALLATION 2. Take off the lens cover protecting the camera lens. This camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Precautions before installation Ensure you read out the following instructions before installing the camera: •... - Page 11 Removing a Micro SD card Installation (mount plate) Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD [Directly installing on wall/ceiling] card from the slot. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. Before removing the Micro SD card, in <Storage>, set the device to <Off>...
- Page 12 outdoor vandal dome camera [Installing using pipe] 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-1. Attach the installation template and drill holes for screws and cables. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. 2-2.
- Page 13 1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. [Installing the network cable] (IP66) [Installing audio/alarm cables] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. 2-2.
- Page 14 outdoor vandal dome camera Installing the camera module 4. Join the mount plate with the camera case. 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. A magnet is embedded at the bottom of the module Take caution not to allow any foreign objects between the attaching surfaces.
- Page 15 Assembling the dome cover [Using Weather cap] 1. Remove the screws from the dome cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. Make sure to firmly tighten the fastening screws so that there is no water damage issue. TR20 TR20 2.
- Page 16 outdoor vandal dome camera Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
-
Page 17: Indoor Dome Camera
indoor dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Pipe-cover Mount-plate Camera-case Camera-module Dome-cover <XND-9082RV/XND-8082RV> IR LED Illumination Sensor Reset button Zoom/Focus Network Control Button Port Option (not included) Microphone cable port Audio/Alarm cable Micro SD card slot SBC-160B... -
Page 18: Installation
indoor dome camera INSTALLATION 2. Take off the lens cover protecting the camera lens. This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Precautions before installation Ensure you read out the following instructions before installing the camera: •... - Page 19 Removing a Micro SD card Installation (mount plate) Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD [Directly installing on wall/ceiling] card from the slot. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. Before removing the Micro SD card, in <Storage>, set the device to <Off>...
- Page 20 indoor dome camera [Installing using pipe] 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-1. Attach the installation template and drill holes for screws and cables. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. 2-2.
- Page 21 1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer English _21...
- Page 22 indoor dome camera Installing the camera module [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. A magnet is embedded at the bottom of the module Take caution not to allow any foreign objects between the attaching surfaces.
- Page 23 Assembling the dome cover [Directly installing on wall/ceiling] 1. Assemble the dome cover. Make sure to firmly tighten the fastening screws so that there is no water damage issue. TR20 Be careful not to alter the monitoring direction of your camera. English _23...
-
Page 24: Flush Mount Dome Camera
flush mount dome camera flush mount dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Bracket Housing Camera-module <XND-9082RF/XND-8082RF> Dome-cover IR LED Illumination Sensor Reset button Zoom/Focus Network Control Button port Audio/Alarm cable Micro SD card slot port Power port... -
Page 25: Installation
INSTALLATION 2. Take off the lens cover protecting the camera lens. This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Precautions before installation Ensure you read out the following instructions before installing the camera: •... - Page 26 flush mount dome camera Removing a Micro SD card Installation (housing) Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD 1. Attach the installation template to the ceiling and mark its location with a pencil. card from the slot.
- Page 27 3. Connect the safety cable. 4-2. Pull out necessary cables among network/power/audio/alarm cables through the pipe. A safety cable is not provided. e.g. [Using pipe] 4-1. Install the pipe in a fitting hole. ¾” NUT ½” NUT English _27...
- Page 28 flush mount dome camera Installation (camera case) [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. Use a cable bushing compliant with the network cable to be connected. 2-2. Use the cap installer to pass through the RJ45 cable. Components: use a cable with the diameter of Ø5 to 8.5 Cap Installer [Installing network/power cables]...
- Page 29 Installing the camera module [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. A magnet is embedded at the bottom of the module Take caution not to allow any foreign objects between the attaching surfaces.
- Page 30 flush mount dome camera Assembling the dome cover Waterproofing cables If there is any possibility of moisture intrusion through the gap of the cable, please waterproof the concerned 1. Assemble the dome cover. area with waterproof butyl rubber tape (can be purchased in stores) as below. Make sure to firmly tighten the fastening screws so that there is no water damage issue.
-
Page 31: Outdoor Bullet Camera
outdoor bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Pipe-cover Sunshield fixing screw Mount plate Sunshield Bottom cover <XNO-9082R/XNO-8082R> Camera body Network port Reset button Test monitor out port Zoom/Focus Audio/Alarm cable Control Button port Micro USB... -
Page 32: Installation
outdoor bullet camera INSTALLATION Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. - Page 33 Installation (Mount plate) [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. 2-2. Separate the pipe cover of the Mount plate by pressing its sides. 1-2.
- Page 34 outdoor bullet camera 2-3. Place the pipe on the Mount plate. 1-4. Mount the cable bushing to the Bottom cover. 2-4. Fix the Mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (Bottom cover) [Installing the network cable] 2-1.
- Page 35 2-3. Mount the cable bushing to the Bottom cover. 4. Join the Mount plate with the Bottom cover. [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the Bottom cover. English _35...
- Page 36 outdoor bullet camera Installing the camera module 3. Attach the camera body to the Bottom cover. 1. Hang the safety cable up on a hook that looks like an arrow in the Bottom cover. Make sure to firmly tighten the fastening screws so that there is no water damage issue. e.g.
- Page 37 Outdoor installation 5. Assemble the sunshield to the camera body using sunshield fixing screw. When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
-
Page 38: Box Camera
box camera box camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Mounting Bracket Screw Hole CS mount Lens (not included) Auto Iris Lens port Test monitor out port <XNB-9002/XNB-8002> Audio cable port Micro SD card Compartment Option (not included) Micro USB port... -
Page 39: Mounting The Lens
MOUNTING THE LENS Disconnect the power before proceeding. Focusing The CS mount Lens are not included in the product package. Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that It is recommended that megapixel lens are use on this camera to optimise performance. -
Page 40: Inserting/Removing A Micro Sd Card
box camera INSERTING/REMOVING A MICRO SD CARD Inserting a Micro SD card Removing a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. -
Page 41: Installation & Connection
installation & connection ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA Adjust the direction of IR LEDs not to hinder their view by an instrument. Tilt Lens rotation ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. At this time, rotating the main body of the camera in the left and right direction is called PAN, and adjusting Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any). -
Page 42: Connecting With Other Device
installation & connection CONNECTING WITH OTHER DEVICE WiFi dongle WiFi dongle SOFT AP SOFT AP Monitor for installation Grounding cable Power Ethernet Power Monitor for installation Ethernet <XNV-9082R/XNV-8082R/XND-9082RV/XND-8082RV/XND-9082RF/XND-8082RF> <XNB-9002/XNB-8002> The Test Monitor Out port of the product is provided for easier installation, and is not recommended for monitoring purposes. Monitor for installation The Micro USB port of the product is provided for easier installation, and is not recommended for monitoring purposes. - Page 43 Ethernet Connection Power Supply Connect the Ethernet cable to the local network or to the Internet. Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. Connecting WiFi If the power sources for PoE and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE and Camera Setup DC 12 V.
- Page 44 installation & connection Connecting to Audio Input/Output • Audio Codec - Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz) Speaker - Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)
- Page 45 Connecting to the I/O port box NETWORK Connect the Alarm I/O cable to the corresponding port of the port box. 1 2 3 4 5 6 AUDIO AUDIO LINK RESET FOCUS VIDEO NETWORK 1 : ALARM 1 4 : NC 1 2 3 4 5 6 AC 24V 2 : ALARM 2...
- Page 46 installation & connection To connect the external sensor Connect one of the 2 signal lines to the [ALARM #1] port (if you want this to be the input port) and the remaining one to the [GND] port. Alarm In Wiring Diagram External Inside of the camera VCC_3.3V...
-
Page 47: Network Connection And Setup
network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1. -
Page 48: Using Device Manager
If using a Broadband Router • IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Technical Guides>-<Online Tool> menu at Hanwha Techwin website ex) 192.168.1.2~254, 192.168.0.2~254, (http://www.hanwha-security.com). -
Page 49: Manually Registering Camera
AUTOMATICALLY CONFIGURING IP Configuring Dynamic IP Receive IP address from DHCP 1. Click the camera from the list that you want to automatically • Example of the Dynamic IP environment configure the IP. XNV-9082R - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. -
Page 50: Port Range Forward (Port Mapping) Setup
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras • You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the •... -
Page 51: Connecting To The Camera From A Shared Local Pc
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser. -
Page 52: Web Viewer
web viewer web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. 1. Launch the Internet browser. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. - The login window is displayed. -
Page 53: Password Setting
PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network. - Page 54 appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION Voice is not recorded even though When an Windows 10 user accesses y You must enable the <Audio In> check box in <Basic> - <Video Profile>. y This is what happens when microphone driver has been set to Realtek driver. audio input settings are configured.
- Page 55 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.