Installation - Maxus EX1001 Operating Instructions Manual

Oilless Compressors
General Safety
Information
(Cont.)
OPERATIONAL SAFETY
Since the air compressor and other
components (material pump, spray
guns, filters, lubricators, hoses, etc.)
used, make up a high pressure
pumping system, the following safety
precautions must be observed at all
times:
1. Read all manuals included
with this product carefully.
Be thoroughly familiar
with the controls and the
proper use of the
equipment.
2. Follow all local electrical and safety
codes, as well as in the U.S.A.,
National Electrical Codes (NEC) and
Occupational Safety and Health Act
(OSHA).
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.
4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the pump
or unit.
6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
Motors, electrical equipment
and controls can cause
electrical arcs that will ignite
a flammable gas or vapor.
Never operate or repair in or near a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
Compressor parts may be
hot even if the unit is
stopped.
9. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
www.maxustools.com
10. If the equipment should start to
abnormally vibrate, STOP the
engine/motor and check
immediately for the cause.
Vibration is generally a warning of
trouble.
11. To reduce fire hazard, keep
engine/motor exterior free of oil,
solvent, or excessive grease.
or attempt to adjust safety valve. Keep
safety valve free from paint and other
accumulations.
MANUAL
Never attempt to repair or
modify a tank! Welding,
drilling or any other
modification will weaken the
tank resulting in damage from rupture
or explosion. Always replace worn or
damaged tanks.
from tank daily.
12. Tanks rust from moisture build-up,
which weakens the tank. Make sure
to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and
corrosion.
13. Fast moving air will stir up dust and
debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.
SPRAYING PRECAUTIONS
Do not spray flammable
materials in vicinity of open
flame or near ignition
sources including the
compressor unit.
14. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
15. Use a face mask /
respirator when spraying
and spray in a well
ventilated area to prevent
health and fire hazards.
16. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.
17. When spraying or cleaning with

Installation

LOCATION
The tank must sit level or slope slightly
towards the drain valve to allow the
Never
tank to drain properly.
remove
It is extremely important to install the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than
100°F.
A minimum clearance of 4 inches
between the compressor and a wall is
required because objects could obstruct
air flow.
Drain
the compressor air inlet near steam,
liquid
paint spray, sandblast areas or any
other source of contamination. This
debris will damage the motor.
ELECTRICAL INSTALLATION
and electrical connections should be
performed by a qualified electrician.
Installation must be in accordance with
local codes and national electrical
codes.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
Figure 1
2
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
120 volt circuit and has a grounding
plug that looks like the plug
illustrated in Figure 1. Make sure the
product is connected to an outlet
having the same configuration as the
plug. This product must be
grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding wire
with an appropriate grounding plug.
Cord must be plugged into an outlet
that is properly installed and
grounded in accordance with all
local codes and ordinances.
Grounded
Pin
TEST
Grounded Outlet
Do not
locate
All
wiring
RESET