Related Manuals for MasterCraft 060-1349-2
Summary of Contents for MasterCraft 060-1349-2
- Page 1 060-1349-2 BRUSHLESS GRASS TRIMMER INSTRUCTION IMPORTANT: Read and understand this instruction manual thoroughly MANUAL before using the product.
- Page 2 headline bars continuation tabs notes warnings...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Technical Specifications Safety Guidelines Key Parts Diagram Operating Instructions Maintenance Troubleshooting Parts List Warranty NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-800-689-9928. SAVE THESE INSTRUCTIONS •... -
Page 4: Technical Specifications
060-1349-2 | contact us 1-800-689-9928 TECHNICAL SPECIFICATIONS Rated Voltage 20 V d.c. Maximum Speed 7,100 RPM Cutting-line Type 0.08” (2 mm) twisted nylon line Cutting Width 12” (30.5 cm) *Maximum battery voltage without workload; with workload nominal voltage is 18 V. -
Page 5: Safety Guidelines
SAFETY GUIDELINES: WARNING! Safety symbols in this Instruction Manual are used to flag possible dangers. The safety symbols and their explanations require your full understanding. The safety warnings do not, by themselves, eliminate any danger, nor are they substitutes for proper accident prevention measures. - Page 6 060-1349-2 | contact us 1-800-689-9928 PERSONAL SAFETY • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
- Page 7 • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. • Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
- Page 8 060-1349-2 | contact us 1-800-689-9928 V ..... Volts A ..... Amperes Hz ....Hertz W ....Watts min ....Minutes ....Alternating current continuation tabs or d.c..Direct current ....No-load speed ....Class II Construction RPM ....
- Page 9 • If the power tool should start to vibrate abnormally or become noisy, stop the motor and check immediately for the cause. Abnormal noise is generally a warning of trouble. • Make sure all proper guards and other safety devices are properly and securely attached before using this product.
-
Page 10: Key Parts Diagram
060-1349-2 | contact us 1-800-689-9928 PACKAGE CONTENTS: Cordless grass trimmer, front-assist handle, guard, screw knob, bolt, hexagon screws (2), screw with washer (2) for the guard, wrench. KEY PARTS DIAGRAM continuation tabs notes Description No. Description... -
Page 11: Operating Instructions
OPERATING INSTRUCTIONS UNFOLD THE SHAFT (fig 1-fig 2) fig 1 1. Remove the battery pack from the trimmer. 2. Put the trimmer on the ground and carefully unfold the shaft. Make sure that the cable is inside the shaft so that it will not be pinched when closing the joints. - Page 12 060-1349-2 | contact us 1-800-689-9928 MOUNTING THE GUARD (fig 3-fig 4) fig 3 1. Remove the battery pack from the trimmer. 2. Lift the trimmer head and face it upward; align the Guard groove on the bottom of the guard with the raised portion on the base of the trimmer head, and then slide the guard onto the base (fig 3).
- Page 13 MOUNTING THE FRONT-ASSIST HANDLE (fig 5) 1. Remove the battery pack from the trimmer. fig 5 2. Remove the screw knob and the bolt from the front- Front-assist assist handle. handle 3. Press the front-assist handle onto the shaft of the grass trimmer.
- Page 14 060-1349-2 | contact us 1-800-689-9928 HOLDING THE GRASS TRIMMER (fig 7) fig 7 Before operating the unit, stand in the operating position and check that: • The operator is wearing eye protection and proper clothing. •...
- Page 15 TO START/STOP THE GRASS TRIMMER fig 8 (fig 8) Lock-off button Before starting the grass trimmer: • Make sure that you have a secure and balanced footing. • Stand upright and hold the grass trimmer in a relaxed position. • Make sure that the cutting line is not touching the ground or any other objects.
- Page 16 060-1349-2 | contact us 1-800-689-9928 ADJUSTING THE CUTTING LINE LENGTH fig 10 (fig 10) The trimmer head allows the operator to release more cutting line without stopping the motor. As line becomes frayed or worn, additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer.
- Page 17 WIND THE SPOOL WITH NEW LINE (fig 11-fig 16) fig 11 fig 12 4 1/2” (11 cm) fig 13 fig 14 fig 15 fig 16 Slot...
- Page 18 060-1349-2 | contact us 1-800-689-9928 (fig 11). 1. Press the two release tabs on the spool base and remove the spool retainer by pulling it straight out 2. Remove the spool. Use a clean cloth to clean the inner surfaces of the spool retainer and spool base.
-
Page 19: Maintenance
MAINTENANCE CHECK FOR DAMAGED/WORN PARTS BEFORE EACH USE Check the bump head, guard, and front-assist handle, and replace any parts that are cracked, warped, bent, or damaged in any way. The line-cutting blade on the edge of the guard can dull over time. It is recommended that you periodically sharpen it with a file or replace it with a new blade. -
Page 20: Troubleshooting
060-1349-2 | contact us 1-800-689-9928 TROUBLESHOOTING Problem Possible causes Solutions The battery pack is depleted. Charge the battery pack. Stop the trimmer, remove the bat- The motor shaft or trimmer head is tery, and remove the grass from the bound with grass. -
Page 21: Parts List
EXPLODED VIEW... - Page 22 060-1349-2 | contact us 1-800-689-9928 No. Part No. Description No. Part No. Description Lower Housing 2824019000 5620512000 Hexagon Socket Screw Assembly 3800123000 Trimmer Line 5650020000 Spring Washer 3127635000 Mounting Wire Holder 5650016000 Plain Washer...
-
Page 23: Warranty
This product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: a) Component A: Batteries, chargers and carrying case, which are guaranteed for a period of 2 years from the date of original retail purchase against defects in workmanship and materials;... - Page 24 060-1349-2 | contact us 1-800-689-9928 h) this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners;...
Need help?
Do you have a question about the 060-1349-2 and is the answer not in the manual?
Questions and answers
how to wind new trimmer line
To wind new trimmer line for the MasterCraft model 060-1349-2:
1. Wind the line in the direction indicated on the spool.
2. Place the ends of the line into the two opposite notches on the spool, leaving about 5 inches (12.5 cm) protruding from each side.
3. Align the notches (with the lines) to the eyelets in the spool retainer and position the spool into the retainer.
4. While holding the spool and retainer, pull one line end to release it from the notch; repeat for the other end.
5. With the spool base facing down, align the slots in the retainer with the tabs on the spool base and press down evenly until it snaps into place.
Always clean the spool and retainer before reassembly, and ensure proper alignment to avoid malfunction.
This answer is automatically generated