− 31.30 inHg) Ambient Temperature in Charge Mode Not to exceed 28_ C Stryker reserves the right to change specifications without notice. WARNING / CAUTION / NOTE DEFINITION The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
Introduction SET−UP PROCEDURES It is important that the Model 660Z Stretcher is working properly before it is put into service. The following list will help ensure that each part of the unit is checked. Plug the power cord into a properly grounded, hospital grade wall receptacle. The 12 volt batteries that provide power to the drive wheel and back−up power to the unit functions will charge whenever the power cord is plugged into the wall socket.
Introduction SYMBOLS Warning, Refer to Service/Maintenance Manual Alternating Current Type B Equipment: equipment providing a particular degree of protection against elec- tric shock, particularly regarding allowable leakage current and reliability of the protec- tive earth connection. Class 1 Equipment: equipment in which protection against electric shock does not rely on BASIC INSULATION only, but which includes an additional safety precaution in that means are provided for the connection of the EQUIPMENT to the protective earth con- ductor in the fixed wiring of the installation in such a way that ACCESSIBLE METAL...
Preventative maintenance should be performed at a minimum of annually. A preventative maintenance pro- gram should be established for all Stryker Medical equipment. Preventative maintenance may need to be performed more frequently based on the usage level of the product.
If these types of products are used to clean Stryker patient handling equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried following cleaning. Failure to properly rinse and dry the stretchers will leave a cor- rosive residue on the surface of the stretcher, possibly causing premature corrosion of critical components.
Service Information WARNING Always unplug the power cord and rotate the “ON/DRIVE − OFF/MANUAL” switch to the OFF position before service or cleaning. LITTER TOP REMOVAL Required Tools: 1/2” Socket w/Extension 3/8” Drive Ratchet Standard Screwdriver Side Cutters 1. Unplug the stretcher power cord from the wall socket. 2.
Service Information HEAD END JACK REMOVAL Required Tools: 1/2” Socket w/Extension 3/8” Drive Ratchet 1. Remove the litter from the stretcher (see procedure on page 11). 2. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the two hex head screws holding the jack base to the stretcher base frame.
Page 14
Service Information FOOT END JACK REMOVAL Required Tools: 1/2” Socket w/Extension 3/8” Drive Ratchet 1. Remove the litter from the stretcher (see procedure on page11). 2. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the kep nut securing the plastic battery cover to the batteries.
Service Information BATTERY REMOVAL Required Tools: 1/2” Socket w/Extension 3/8” Drive Ratchet CAUTION Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after han- dling.
Service Information ZOOM CARRIAGE ASSEMBLY REMOVAL Required Tools: 1/2” Socket w/Extension 1/4” Drive Ratchet 1. Remove the litter from the stretcher (see procedure on page11). 2. Lift the base hood off the base frame. 3. Put the base brake/steer pedal in the neutral position. 4.
Service Information CAM BRACKET ASSEMBLY REMOVAL Required Tools: 1/2” Socket w/Extension 1/4” Drive Ratchet 1. Remove the litter from the stretcher (see procedure on page11). Lift the base hood off the base frame. 2. Put the base brake/steer pedal in the neutral position. Remove the 2 rue ring cotters and clevis pins from the center of the brake rod in the middle of the cam arm assembly.
Service Information RELEASE PEDAL ADJUSTMENT Required Tools: None 1. Manually disengage the release pedal swivel (item J on page 38) from the release pedal assembly. 2. To increase the release rod engagement with the release valve, turn the release pedal swivel clockwise on the threaded release rod.
Service Information PCB DISPLAY BOX ASSEMBLY REMOVAL Required Tools: 7/16” Socket w/Extension 3/8” Drive Ratchet T−40 & T−27 Torx Sockets 1/2” Wrench 1. If the unit is equipped with an IV Pole, remove the nut and bolt holding the IV pole in the socket and remove the IV pole.
Standard Base Assembly Assembly part number 1040−010−001 (reference only)
Page 23
Standard Base Assembly See Detail C Ground Cable from Carriage Electronics Box DETAIL C Cam Hanger Bracket HEAD END Standard Power Cord 1040−060−060 (see page Cord Reel Option 1040−060−050 (see page...
Page 24
Standard Base Assembly 1040−010−320 1040−060−050 or Cord 1040−060−060 Clamp See Detail D DETAIL B DETAIL D See Detail B HEAD END To handle control box See Detail E DETAIL E FOOT END...
Standard Base Assembly See Detail F DETAIL F Item Part No. Part Name Qty. Item Part No. Part Name Qty. 0005−040−000 Carriage Bolt 0081−330−000 Radial Bearing 0011−447−000 Washer (page Base Ass’y/Std. Brakes 0013−038−000 Ext. Tooth Lock Washer (page Brake Rod Assembly 0014−007−000 Washer (page Base Ass’y/Dual Hyd.
Page 26
1040−003−191 Brake Rod Assembly Item Part No. Part Name Qty. 0026−067−000 Slotted Spring Pin 1040−003−013 Brake Rod 0753−003−099 Butterfly “V” Pedal...
Overtravel Spring Assembly Assembly part number 1040−007−001 (reference only) Item Part No. Part Name Qty. Item Part No. Part Name Qty. 0011−447−000 Washer 0081−240−000 Flange Bearing 0016−036−000 Nylock Hex Nut 1040−007−003 Fork Tray 0026−330−000 Clevis Pin 1040−007−005 Lift Fork Weldment 0026−331−000 Clevis Pin 1040−007−011...
Page 30
Zoom Carriage Assembly Assembly part number 1040−020−001 (reference only) 1040−010−821 Ground Cable...
Base Assembly with Dual−Sided Hydraulics Assembly part number 1040−005−300 (reference only) Insert pump ram into keyhole slot on both ends. Lower pump connecting rod weldment onto pump ram as shown. Insert item W to retain pump connecting rod.
Page 39
Base Assembly with Dual−Sided Hydraulics Insert spring hook thru hole in pump connecting rod weldment Attach other hook to return Insert spring hook into hook on spring hook as shown. release pedal assembly. Insert other hook into pump connecting rod weldment as shown.
Page 40
Base Assembly with Dual−Sided Hydraulics SEE DETAIL A SEE DETAIL B Insert foot end release rod into release valve assembly as shown DETAIL A Insert head end release rod into release valve assembly as shown DETAIL B...
Page 41
Base Assembly with Dual−Sided Hydraulics Item Part No. Part Name Qty. 0011−023−000 Washer 0014−071−000 Washer 0023−288−000 Hex Washer Hd. Screw 0027−031−000 Hair Pin Cotter 0038−497−000 Extension Spring 0753−004−014 Head End Release Rod (page Release Pedal Assembly 0753−004−132 Release Pedal Swivel 0753−005−037 Pump Connecting Rod 0753−005−044...
0753−004−101 Release Pedal Assembly Item Part No. Part Name Qty. 0025−079−000 Rivet 0753−004−004 Release Pedal Weldment 0753−004−029 Release Pedal Standoff 0753−004−320 Release Pedal Support 0753−004−321 Release Pedal Support 1061−201−127 Short Uni Pedal...
Head End Pump Pedal Assembly Assembly part number 0753−005−185 (reference only) Item Part No. Part Name Qty. 0026−343−000 Groove Pin 0715−001−140 Vinyl Tube 0753−005−044 Pump Pedal Bushing 0753−005−180 Head End Pump Pedal Weldment 0753−201−126 Pump Pedal...
0660−001−116 See Below for Colors 0660−001−015 Specification Label Item Part No. Part Name Qty. 1040−010−017 Stryker Logo Label 1040−010−134 Zoom Bellows Assembly (page Zoom Base Hood 1040−010−016 Zoom Logo Label Set Part Number Brake/Drive Label, Brake/Drive Label, Lift/Lower Label, Left...
Page 46
Base Labeling Assembly BASE HOOD DEPARTMENT LABELS Department Label P/N Department Label P/N Emergency 1010−900−215 Nuclear Medicine 1010−900−255 PACU 1010−900−220 Ambulatory Surgery 1010−900−260 Transport 1010−900−225 G.I. Lab 1010−900−265 Surgery 1010−900−230 Cath. Lab 1010−900−270 Extended Stay 1010−900−235 Same Day Surgery 1010−900−275 Maternity 1010−900−240 Cardio.
1040−010−310 Base Hood Assembly Item Part No. Part Name Qty. 0001−001−000 Flat Head Socket Screw 0014−105−000 Countersunk Washer 0052−902−000 U−Nut Fastener 1040−010−006 Base Hood 1040−010−007 Electrical Hood...
1040−060−060 Standard Power Cord Assembly Item Part No. Part Name Qty. 0034−406−000 Strain Relief 0039−255−000 Power Cord 1040−060−033 Cord Bracket 1040−060−050 Optional Cord Reel Assembly Female IEC Male Plug Cord to Control Box Item Part No. Part Name Qty. 0003−214−000 Hex Hd.
29” Zoom Handle Assembly Assembly part number 1040−050−029 (reference only) Load Cell Cable Communication Cable From Electronics Box...
Page 54
29” Zoom Handle Assembly Item Part No. Part Name Qty. 0023−288−000 Hex Washer Hd. Screw 0003−367−000 Hex Hd. Cap Screw 0013−019−000 Ext. Tooth Lock Washer 0013−038−000 Ext. Tooth Lock Washer 0023−305−000 Hex Washer Hd. Screw 0028−196−000 External Retaining Ring 1040−050−108 Pivot Bolt 1001−226−016 Pivot Bearing...
Page 55
1040−050−030 Right Handle Grip Assembly See Detail A WIRE ROUTING DETAIL A WIRE ROUTING SIDE 2...
Page 56
1040−050−030 Right Handle Grip Assembly Item Part No. Part Name Qty. 0023−302−000 Pan Hd. Thrd.−Frm. Screw 1040−050−031 Light Pipe 1040−050−032 Grip Button 1040−050−303 Right Bottom Grip 1040−050−034 Right Top Grip 1040−050−035 Right Handle Weldment 0038−111−000 Cable Tie 1040−050−801 Handle Switch Cable 1040−050−802 Handle Extension Cable 0038−523−000...
Page 57
1040−050−040 Left Handle Grip Assembly See Detail A WIRE ROUTING DETAIL A WIRE ROUTING SIDE 2...
Page 58
1040−050−010 Left Handle Grip Assembly Item Part No. Part Name Qty. 0023−302−000 Pan Hd. Thrd.−Frm. Screw 1040−050−031 Light Pipe 1040−050−032 Grip Button 1040−050−043 Left Bottom Grip 1040−050−044 Left Top Grip 1040−050−045 Left Handle Weldment 0038−111−000 Cable Tie 1040−050−801 Handle Switch Cable 1040−050−802 Handle Extension Cable 0038−523−000...
Page 59
Siderail to Litter Assembly, Fold−to−Head...
Page 60
Siderail to Litter Assembly, Fold−to−Head FOOT END...
Page 61
Siderail to Litter Assembly, Fold−to−Head Item Part No. Part Name Qty. 1001−226−116 Pivot Bearing 1001−226−016 Pivot Bearing 1001−226−015 Pivot Sleeve 1001−226−017 Siderail Spring 1001−326−027 Right Spindle 1001−326−031 Lock Spindle Weldment, Rt. 1001−326−028 Left Spindle 1001−326−033 Lock Spindle Weldment, Lt. 1001−226−020 Siderail Spring Spacer 0025−172−000 Rivet...
Page 62
Siderail to Litter Assembly, Fold−to−Foot...
Page 63
Siderail to Litter Assembly, Fold−to−Foot HEAD END...
Page 64
Siderail to Litter Assembly, Fold−to−Foot Item Part No. Part Name Qty. 1001−226−116 Pivot Bearing 1001−226−016 Pivot Bearing 1001−226−015 Pivot Sleeve 1001−226−017 Siderail Spring 1001−326−027 Right Spindle 1001−326−031 Lock Spindle Weldment, Rt. 1001−326−028 Left Spindle 1001−326−033 Lock Spindle Weldment, Lt. 1001−226−020 Siderail Spring Spacer 0025−172−000 Semi−Tubular Rivet...
Pneumatic Fowler Assembly Assembly part number 0660−031−010 (reference only) HEAD END Item Part No. Part Name Qty. 0003−360−000 Hex Hd. Cap Screw 0004−104−000 But. Hd. Cap Screw 0011−179−000 Washer 0014−021−000 Washer 0016−116−000 Hex Nut 0016−119−000 Hex Nut 0015−060−000 Metric Jam Nut 1211−131−026 Gas Spring Cap 0052−306−000...
Page 67
Fowler Assembly Assembly part number 1711−131−020 (reference only) Item Part No. Part Name Qty. Item Part No. Part Name Qty. 1001−001−036 Hole Plug 0016−118−000 Hex Nut 1211−231−025 Trip Bar Pivot 0004−455−000 But. Hd. Cap Screw 1501−031−013 Fowler Tube 0037−064−000 Grommet Bumper 1510−231−012 Fowler Skin (Fiberresin) 0007−070−000 Truss Hd.
Fiberresin Stationary Foot Section Assembly Assembly part number 1731−019−001 (reference only) Item Part No. Part Name Qty. 0025−171−000 Blind Rivet 0037−208−000 Hole Plug 0753−010−032 Fiberresin Ft. Section Skin 7900−001−102 Velcro Pile 24 1/2”...
Page 69
Patient Transfer System to Litter Assembly Assembly part number 1211−132−003 (reference only) HEAD END Item Part No. Part Name Qty. 0011−418−000 Washer (page Transfer System Ass’y, Lt. (page Transfer System Ass’y, Rt. 0016−119−000 Nylock Nut 0003−360−000 Hex Hd. Cap Screw...
Page 70
1211−232−007 Patient Transfer System Assembly, Left Item Part No. Part Name Qty. (page Transfer Board Assembly 1211−132−016 Transfer Board Swivel 1211−132−020 Transfer Board Link 1211−132−031 Transfer Bd. Pivot Ass’y, Lt. 0026−076−000 Spring Pin 0026−112−000 Spring Pin 0011−350−000 Washer 1211−232−011 Transfer Bd. Arm Wldmt. 1211−132−029 Link Swivel 0014−007−000...
Page 71
1211−232−008 Patient Transfer System Assembly, Right Item Part No. Part Name Qty. (page Transfer Board Assembly 1211−132−016 Transfer Board Swivel 1211−132−020 Transfer Board Link 0026−076−000 Roll Pin 0026−112−000 Roll Pin 0011−350−000 Washer 1211−132−030 Transfer Bd. Pivot Ass’y, Rt. 1211−232−012 Transfer Bd. Arm Wldmt. 1211−132−029 Link Swivel 0014−007−000...
Page 72
1211−132−009 Transfer Board Assembly Item Part No. Part Name Qty. 0025−125−000 Pop Rivet 0025−126−000 Pop Rivet 1211−132−004 Transfer Board 1211−132−017 Transfer Bd. Sleeve Wldmt. 1211−132−019 Stiffener Weldment...
1211−151−000 Foot End Steering Handles Assembly HEAD END Item Part No. Part Name Qty. 0003−356−000 Hex Hd. Cap Screw 0003−355−000 Hex Hd. Cap Screw 0016−118−000 Fiberlock Nut 0023−282−000 Self−Tapping Screw 0023−283−000 Self−Tapping Screw 0026−114−000 Roll Pin 1211−030−034 Cover, Hole/Slot 1211−030−037 Cover, Hole/Hole 1211−351−004 P.U.P.
Page 74
1211−351−010 Push Handle Assembly Item Part No. Part Name Qty. 1010−354−024 Stop Link 1211−151−018 Sleeve Assembly 0026−118−000 Roll Pin...
Optional 2−Stage I.V. Pole Mounting Assembly Assembly part numbers 1711−110−000 (Head End) 1711−112−000 (Foot End) FOOT END HEAD END Item Part No. Part Name Qty. 0003−356−000 Hex Hd. Cap Screw 0004−452−000 But. Hd. Cap Screw 0016−116−000 Fiberlock Nut 0016−118−000 Fiberlock Nut 1211−310−112 I.V.
Page 77
1211−210−010 Optional 2−Stage I.V. Pole Assembly Item Part No. Part Name Qty. 0008−031−000 Soc. Hd. Cap Screw 0052−017−000 Washer 0926−400−162 Spacer 1211−210−029 2nd Stage Assembly 1001−359−013 Dampener 1001−159−028 Base Tube 1010−059−016 I.V. Hook (page I.V. Pole Latch 1001−359−112 Pivot...
Optional 3−Stage I.V. Pole Mounting Assembly Assembly part numbers 1711−111−000 (Head End) 1711−113−000 (Foot End) FOOT END HEAD END Item Part No. Part Name Qty. 0003−356−000 Hex Hd. Cap Screw 0004−452−000 But. Hd. Cap Screw 0016−116−000 Flexlock Nut 0016−118−000 Fiberlock Nut 1211−310−112 I.V.
Page 80
1211−211−010 Optional 3−Stage I.V. Pole Assembly Item Part No. Part Name Qty. 0007−004−000 Truss Hd. Machine Screw 0026−076−000 Roll Pin 0052−017−000 Spacer 1211−210−031 2nd Stage Assembly 0926−400−162 Spacer (page 3rd Stage Assembly 1001−161−023 Base Tube 1010−059−016 I.V. Hook 1010−061−014 Collar (page I.V.
3−Stage I.V. Pole 3rd Stage Assembly Assembly part number 1211−110−032 (reference only) NOTE Item F, part number 1010−061−018 is left hand thread. When removing it, turn clockwise to loosen it. Item Part No. Part Name Qty. 0031−021−000 Ball 0038−303−000 Compression Spring 1010−061−013 Ball Retainer 1010−061−016...
0926−039−000 Optional Defibrillator Tray Assembly Assembly part number 0926−039−010 (reference only) Umbrella Nut/Crosstube Detail Strap Securing Detail Item Part No. Part Name Qty. Item Part No. Part Name Qty. 0946−039−004 Tray 0946−039−003 Support Tube 0926−039−016 Crosstube 0926−001−082 Label 0025−055−000 Rivet 1010−050−021 Long Strap 0926−039−009...
Page 87
1001−055−000 Heel Stirrup and Support Assembly Assembly part number 1001−055−010 (reference only) FOOT END Item Part No. Part Name Qty. 0003−359−000 Hex Hd. Cap Screw 0011−159−000 Flat Washer 0016−118−000 Nylock Hex Nut (page Stirrup Support Ass’y, Rt. (page Stirrup Support Ass’y, Lt. (page Stirrup Assembly...
Page 88
1001−055−015 Right Stirrup Support Assembly Item Part No. Part Name Qty. 0650−002−032 Lock Screw Assembly 0966−051−019 Wedge Lock, Modified 1001−055−011 Mounting Bracket 1010−055−016 Right Support Tube Wldmt. 0004−494−000 Soc. Hd. Cap Screw 0011−410−000 Washer 1211−117−016 Knob 0026−007−000 Roll Pin 0038−171−000 Compression Spring...
Page 89
1001−055−016 Left Stirrup Support Assembly Item Part No. Part Name Qty. 0650−002−032 Lock Screw Assembly 0966−051−019 Wedge Lock, Modified 1001−055−011 Mounting Bracket 1010−055−026 Left Support Tube Ass’y 0004−494−000 Soc. Hd. Cap Screw 0011−410−000 Washer 1211−117−016 Knob 0026−007−000 Roll Pin 0038−171−000 Compression Spring...
Page 90
1010−055−029 Heel Stirrup Assembly Item Part No. Part Name Qty. 0390−020−013 Stirrup 0390−020−009 Stirrup Holder Assembly 1010−055−030 Extension Tube Assembly 0024−011−000 Knob 0026−043−000 Roll Pin 0022−008−000 Drive Screw...
Page 91
1001−070−000 C−Spine Cassette Holder Assembly Item Part No. Part Name Qty. 1010−070−025 I.V. Adaptor 1010−070−018 Specification Label 0011−447−000 Flat Washer 0004−054−000 But. Hd. Cap Screw (page Support Pole Assembly (page Storage Bracket Ass’y 0016−118−000 Nylock Nut 0003−356−000 Hex Hd. Cap Screw 1001−070−011 Attachment Bracket 0003−355−000...
Page 92
1010−070−010 C−Spine Support Pole Assembly View A−A Item Part No. Part Name Qty. 1010−070−033 Support Tube Cap 0026−006−000 Roll Pin 1010−070−034 Support Arm Weldment 1010−070−042 Cassette Holder Weldment 1010−070−050 Adjustment Tube Weldment 1010−070−030 Base Tube Weldment 1010−070−045 Knob 0025−055−000 Pop Rivet 1010−070−044 Pivot Pin 0026−005−000...
Page 93
1010−070−019 C−Spine Storage Bracket Assembly 6.5” (Ref.) 2” (Ref.) Item Part No. Part Name Qty. 1010−070−020 Storage Bracket Weldment 1010−070−045 Knob 1010−070−023 Storage Label...
If requested by Stryker, products or parts for which a warranty claim is made shall be returned prepaid to Stryker’s factory. Any improper use or any alteration or repair by others in such manner as in Stryker’s judgement affects the product materially and adversely shall...
Stryker will perform all service during regular business hours (9−5) * Replacement parts and labor for products under PM contract will be discounted. ** Does not include any disposable items, I.V. poles (except for Stryker HD permanent poles), mattresses, or damage re- sulting from abuse.
Page 98
European Representative Stryker EMEA RA/QA Director Stryker France ZAC Satolas Green Pusignan Av. De Satolas Green 69881 MEYZIEU Cedex France 3800 E. Centre Ave., Portage, MI 49002 (800) 327−0770 www.stryker.com JH 5/06 0660-109-002 REV B...