Advertisement
Quick Links
Maintenance
Replacing the filter
You will need:
•
3mm Allen Key
• New filter – B9094
1. Turn off the water supply.
2. Remove panel using 3mm Allen key.
I.
For wall hung version remove access panel.
II.
For floor standing version remove floor standing
shroud.
3.
Disconnect filter via the push fit connectors.
*See below*
Recommended replacement of filter every 6 months.
How Super Speedfit Fittings Work
To make a connection, the tube is simply pushed in by hand; the unique
patented John Guest collet locking system then holds the tubing firmly in
place without deforming it or restricting flow.
To disconnect, ensure that the system is depressurised and push the collet
square against the fitting. With the collet held in this position the tube can
be removed.
www.franke‐ws.com
Franke Sissons Ltd., Carrwood Rd, Sheepbridge, Chesterfield S41 9QB
T: +44‐(0)1246‐450255 F: +44‐(0)1246‐451276 E: ws.uk@franke.com
Mounting Instructions and Manual
ANMX330
Wall Hung Drinking Fountain with Bubbler & Water Filter
ANMX331
Wall Hung Drinking Fountain with Bubbler, Bottle filler &
Water Filter
7
EA-Nr.: 7612979010831
EA-Nr.: 7612979010848
B0050
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Franke ANMX330
Summary of Contents for Franke ANMX330
- Page 1 Maintenance Franke Sissons Ltd., Carrwood Rd, Sheepbridge, Chesterfield S41 9QB Replacing the filter T: +44‐(0)1246‐450255 F: +44‐(0)1246‐451276 E: ws.uk@franke.com You will need: Mounting Instructions and Manual • 3mm Allen Key • New filter – B9094 1. Turn off the water supply. 2. Remove panel using 3mm Allen key. For wall hung version remove access panel. For floor standing version remove floor standing shroud. Disconnect filter via the push fit connectors. *See below* Recommended replacement of filter every 6 months. ANMX330 EA-Nr.: 7612979010831 Wall Hung Drinking Fountain with Bubbler & Water Filter How Super Speedfit Fittings Work To make a connection, the tube is simply pushed in by hand; the unique patented John Guest collet locking system then holds the tubing firmly in place without deforming it or restricting flow.
- Page 2 Adjusting the flow rate Important Notes . Before installation, the instructions have to be read and understood. . Once the drinking fountain is installed, the Installation, commissioning and maintenance are to be performed only by a flow rate may require altering. qualified technician according to the instructions provided and in accordance with legal requirements and acknowledged rules of technology. To do this simply adjust the pin located at the front of the water controls. Important ! Before installing, flush the pipes in compliance with DIN 1988 • Bubbler requires flat head screwdriver • Bottle filler requires 4mm allen key GBR Technical data Minimum flow pressure 1,0 Maximum operating pressure 5 bar Recommended flow pressure 3 bar 1 ...
- Page 3 Scope of supply Mounting Mounting the wall hung drinking fountain 1. Place fixing bracket on wall ensuring distance from floor is 15mm lower than required height. *Recommended Heights: Min 685mm, Max 915mm Ensure bracket is level and mark out the 5 hole centres. 3. Remove bracket from wall and drill holes using a 10mm drill bit. 4. Insert rawl plugs into wall and fix bracket to the wall by the 4 corner holes using the screws provided in pack B1125. Description 5. For the central hole, insert remaining screw through filters fixing clip and fixing bracket, into the wall. (See image 1) Bubbler 6. Take your assembled drinking fountain and slide onto the Bottle Filler (for ANMX331/341) fixing bracket securing it in place via the holes on the sides. 6” Filter** 7. Connect the filter to the inlet via the bottom access panel. Secure panel in place once installation is complete. Fixing clip ½” BSP – ¼” Push fit adaptor* ¼” Push fit elbow ¼” Equal tee (for ANMX331/341) 1M length ¼” Blue LLDPE Tubing ½” – 3/8” Brass bush* 1 ¼” Waste body 1 ¼” P Trap/S trap* Fixing pack *Quantities dependent on model purchased ** Replace every 6 months, Part code: B9094 2 ...
- Page 4 Assembling internal components Dimensions Assembling the drinking fountain 1. Undo all fixing screws and strip off any protective film that may not be accessible when the unit is mounted. Remove the fixing bracket and bottom access panel. 2. Remove the back nut from the water bubbler and place it through the hole provided on the top pressing of the drinking fountain. Dependent on customer preference of water flow position, there are two holes for the bubbler to locate. Refit the back nut and tighten. 3. Fit the ½” – 3/8” BSP brass bush to the ½” BSP – ¼” push fit adaptor. Apply a small amount of thread sealant to the threads of the brass bush and bubbler, then secure the two together. *For ANMX331 variant please repeat process for the bottle filler. * 4. Connect the water bubbler and the bottle filler to the filter using the push fit connectors and tubing supplied in pack, see diagrams for further detail. 5. Connect ½” BSP – ¼” push fit adaptor to inlet supply. Fit required amount of tubing and an ¼” elbow to reach filter. *See page 8 for how speedfit fittings work * 6. Take the waste body and secure it onto the M6 x 40 mm screw on the bottom of the pressing. Then attach the 1/ ¼” trap to the waste. Diagram 1: Diagram 2: Filter assembly for Filter assembly for ANMX330 ANMX331 Please note dimensions are same for versions without bottle filler 4 3 ...
Need help?
Do you have a question about the ANMX330 and is the answer not in the manual?
Questions and answers