Advertisement
1.0
GENERAL INFORMATION
1.1
Panblast notice to purchasers and users
1.1.1
All products and equipment designed and
manufactured by PanBlast are intended for use
by experienced users of abrasive blasting
equipment and its associated operations and
abrasive blasting media.
1.1.2
It is the responsibility of the user to:
-
Determine if the equipment and abrasive
media is suitable for the users' intended
use and application.
-
Familiarize
appropriate laws, regulations and safe
working practices which may apply within
the users' working environment.
-
Provide appropriate operator training and
a safe working environment including
operator protective equipment such as,
but not limited to, blasting suit, safety
footwear, protective eyewear and hearing
protection.
1.1.3
PanBlast Standard Terms and Conditions of Sale
apply. Contact your local PanBlast office or
distributor should you require any further
information or assistance.
1.2
!
WARNING!
CAREFULLY BEFORE USING THIS EQUIPMENT.
1.2.1
Heavy metal paint, asbestos and other toxic
material dusts will cause serious lung disease
or death without the use of properly designed
and approved supplied air respiratory (SAR)
equipment by blast operators and all personnel
within the work site area.
1.2.2
The compressor must have adequate output
and the plumbing between the compressor and
the point of attaching the air supply hose must
have sufficient capacity to supply the volume of
air at the pressure required
1.3
Standard safety precautions
1.3.1
Approved safety eyewear, hearing and footwear
protection should be worn at all times by the
operator and anyone else in the immediate area
that may be exposed to any hazards generated
by the abrasive blasting process.
1.3.2
Suitably approved respiratory protection (PPE)
should also be worn when handling abrasive
media, abrasive refuse dust and when carrying
out any service/maintenance work where any
dust may be present.
1.3.3
Any work performed on electrical wiring or
components must only be carried out by
suitably
qualified
trade's personnel.
1.3.4
Under no circumstances should any safety
interlocks / lockouts or features be altered or
disabled in any way.
1.3.5
All equipment must be isolated from the
compressed air supply and electrical power
source prior to any service or maintenance
work being carried out.
themselves
with
any
–
READ
THIS
SECTION
and
registered
electrical
1.3.6
All care must be taken by the operator when
lifting or moving equipment or components in
order to prevent injury. Pressure Blast Pots
must always be emptied of abrasive media
before any attempt is made to move them.
1.3.7
Any modification of the equipment or use of
non-genuine PanBlast™ replacement parts will
void warranty.
1.3.8
Always check the Material Safety Data Sheet
(MSDS) on the abrasive being used to ensure
that it is free of harmful substances, in
particular, free silica, cyanide, arsenic or lead.
1.3.9
Test the surface to be blasted for harmful
substances, taking the appropriate measures to
ensure the safety of all personnel.
1.3.10
The
operator
inspection of all related components prior to
startup of all wearing and safety items to
ensure they are in correct operating order.
In particular check all Hose Couplings and
Nozzle
Holders,
Couplings are fitted correctly, the Safety Pins
are engaged and in good order. Always install
Safety Whip Check Cables at every hose
connection. Ensure that the Blast Nozzle has
been securely screwed into the Nozzle Holder
and the Nozzle Holder has been secured to the
Blast Hose correctly and all screws are engaged.
2.0
INTRODUCTION
2.1
These
instructions
operation and maintenance of the PanBlast™
Pow Air Vac abrasive recovery system.
2.2
The PanBlast™ Pow Air Vac is designed to
perform recovery of any commercial abrasive
from
expendable
aggressive metallic abrasives such as steel grit.
3.0
PREPARATION FOR OPERATION
3.1
Ensure that the Dust Bag is securely fastened in
the correct position located on the underside of
the Top Lid.
3.2
Place the Top Lid onto the supplied abrasive
storage drum and ensure that the Top Lid is
fully sealed around the drum circumference.
3.3
Attach one end of the abrasive Recovery Hose
to the abrasive vacuum spigot located on the
Top Lid. Attach the opposite end of the
abrasive Recovery Hose to the abrasive pick up
wand. Securely fasten both ends of the abrasive
Recovery Hose with the provided hose clamps.
3.4
Attached a suitable main air supply hose (not
supplied) to the 19mm (3/4") main air inlet
ball valve located on the Top Lid. It is
recommended a suitably sized air supply line of
19mm (3/4") ID or larger be utilized to supply
the Pow Air Vac system. Ensure that coupling
safety Locking Pins and Safety Whip Checks are
utilized at each hose connection point.
NOTE:
THE
SUPPLY REQUIRED TO OPERATE THE POW
AIR VAC SYSTEM IS 71 LITRES/SECOND (150
CFM) AT 690KPA (100 PSI).
- 1 -
should
carry
out
a
ensuring
that
all
cover
the
installation,
abrasives
through
MINIMUM
COMPRESSED
ZVP-PC-0100-00-R1
daily
Hose
to
AIR
Advertisement
