Table of Contents
Advertisement
Quick Links
TITAN
Model No. 74846—Serial No. 315000001 and Up
Model No. 74848—Serial No. 315000001 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
Note: Determine the left and right sides of the machine from the normal operating position.
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
ZX Riding Mower
Description
No parts required
Rear hitch
Bolt (5/16 x 2-1/2 inches)
Locknut (5/16 inch)
No parts required
Rollbar
Rollbar support
Reinforcing bracket
ROPS plates
Bolt (1/2 x 3–1/2 inches)
Bolt (1/2 x 4–1/2 inches)
Hex locknut (1/2 inch)
Flat washer (1/2 inch)
Thrust washer
Flange locknut (1/2 inch)
Bolt (5/16 x 3–3/4 inches)
Flange locknut (5/16 inch, may be
pre-installed)
Flat washer (5/16 inch)
No parts required
Ignition key
Operator's Manual
Engine Operator's Manual
Register at www.Toro.com.
Form No. 3394-403 Rev A
Qty.
–
Connect the battery.
1
2
Install the rear hitch.
2
Set up the motion-control levers and the
–
seat.
1
2
2
4
10
2
8
Install the Roll Over Protection System
(ROPS).
8
4
10
2
2
2
–
Check the mower adjustment.
1
1
Complete the setup.
1
Original Instructions (EN)
All Rights Reserved *3394-403* A
Printed in the USA.
Setup Instructions
Use
Advertisement
Table of Contents
Related Manuals for Toro TITAN ZX 74846
Summary of Contents for Toro TITAN ZX 74846
- Page 1 Operator's Manual Complete the setup. Engine Operator's Manual Note: Determine the left and right sides of the machine from the normal operating position. © 2015—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3394-403* A 8111 Lyndale Avenue South Printed in the USA.
-
Page 2: Connecting The Battery
Connecting the Battery Installing the Rear Hitch No Parts Required Parts needed for this procedure: Rear hitch Procedure Bolt (5/16 x 2-1/2 inches) 1. Locate the battery and negative battery cable. Locknut (5/16 inch) 2. Remove the plastic cap from the negative battery post. 3. - Page 3 Setting up the Motion-control Levers and the Seat No Parts Required Procedure 1. Locate the motion-control levers attached, but folded down on the machine. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3.
-
Page 4: Installing The Roll Over Protection System (Rops)
Installing the Roll Over Protection System (ROPS) Parts needed for this procedure: Rollbar Rollbar support Reinforcing bracket ROPS plates Bolt (1/2 x 3–1/2 inches) g028588 Bolt (1/2 x 4–1/2 inches) Hex locknut (1/2 inch) Figure 6 Flat washer (1/2 inch) 1. -
Page 5: Installing The Rollbar
Making Final Adjustments 1. Tighten the fasteners in the order specified in the following table. Figure 6,Figure 7, and Figure 8 will help identify the parts. 1 2 3 Sequence Description Torque 2 4 5 Four bolts on each 400 ± 40 in-lbs side attaching the (45 ±.4 N-m) pivot brackets to... -
Page 6: Checking The Mower Adjustment
Checking the Mower Adjustment No Parts Required Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as necessary. Refer to the Operator's Manual for more information. Completing the Setup Parts needed for this procedure: Ignition key... - Page 7 Notes:...