Advertisement
Congratulations!
You
have
completed
the
basic setup.
Reading the Diagnostic LEDs
Mot
ion LED
How do
I
know the camera is recording?
•
Camera is ready to record (Red)
D
·Camera is recording (Red. blinking)
Turning
Off
Motion and Diagnostic
LEOs
You can turn o
ff
the
motion
and diagnostic LEOs in the
Settings > Cameras >Camera > Show LED for.
See F1 Help for instructions.
Troubleshooting
Camera
connection:
What if
cam
era/video disappears?
1)
Test
another outlet for your camera. perhaps one closer to
your PC
2) Verify that the camera
power
supply and the network
bridge are plugged direct ly 1nto a power outlet and not a
power stnp
3) Check firewall
set
tings or press the Fl key in Commander
Software for additional help
4) Go to Settings >Cameras> Add/Find > Find Cameras.
5) Reset the camera. See Instructions in "Camera Reset
Instructions"
Camera Diagnostic
LED
Which LED
colors
indicate "camera is working"?
e
Connected to
Int
ernet (Green)
e
Connected to Alert Commander (Purple)
e
Connected to Alert Commander & Internet (Blue)
Upgrading Firmware (Wh ite)
Camera in standa lone mode (Yellow)
Not connected to Aler
t
commander or
Internet
(Light Blue)
How to access your cameras away from home ...
The Logitech Alert system includes free remote
viewing
that allows you to see live video from
your
cameras. Just log in to our secure site at http://a lert.logitech.com from an
Internet
-connected
computer
or
use our smartphone apps fo
r
iPhone·
. iPad",
Andro
i
d'~
or B
lackBerry"
devices
Watch from anywhere-for free
What
do 1 do
if the
power
supply cable (yellow connector)
is
too
short?
To lengthen, either use the supplied cable extender o
r
purchase a
longer ethernet (CAT-5e) cable. Longer cables are available for
purchase at www.log itech .com/dvs/ (Accessories)
~/
/~
Want to see more setup tips?
Go to www.
logit
ech.co m/securi
t y/supp ort
Camera
Diagnostic LED
Which LED
colors
indicate
"camera
is not working"?
D
Camera boot-up failed • (Red blinking)
f")
microSD card read/write failure- No microSD
card • (A lternating Red
I
Yellow, blinking)
• See Camera Reset Instructions
for
assistance
FAQs: Find More
Where
can
I
find more information?
Commander Help
You can press the Fl key from any screen 1n the Alert
Commander to access the online Help
syst
em
~
Knowledge Base
Troubleshooting help is available at www.logitech.com/support
Logitech
For
ums
Find and share answers and best practices for Alert products and
services at www.forums.logitech.com
Cust
omer Support
Call1.888.469.4543
Refer
t
o System Requirements Guide
Power Supply
1
Network
Power
Supply Network
Adapter
Diagnostic LEOs
Status LEOs (Top)
What these LEOs tell me:
What these LEOs tell me:
•
Traffic and data is flowing
e
Link to Power Supply
(Green)
(Green)
e
Shows network tra ff ic
(Blue)
Camera Reset Instructions
With the camera connec
t ed
to power. insert a paper clip into
the reset hole located on the back of the camera
.
Press gent ly.
holding for 5 seconds. and t he
n
release. O r, go to Settings >
Reboot/Reset
> Reset
If t
he
camera does not appear after reset. go to Settings >
Cameras >Add/Find
>
Find Cameras If the camera still does
not
operat
e. contact technical support
Resett ing the camera will restore the camera to factory
settings.
However, it w ill not delete video recorded on the
mic roSD care.
On/Off switch for
Power
Su
pp
ly
I
Network Adapter LEOs
How do
I
turn
these LEOs off?
Use the switch
locat
ed on the side
of the power supply o
r
network
adapt
er to disable these diagnostic
LEOs
www.logitech.com
©
2012 Log,tech.
All
nghts reserved. Logotech. the Logotech logo. and other Logotech
marks are owned by log1tech and may
be
rego
stered. All other trddemarks are the
property of theor re;pectove owners. Log1tech assumes no respons
o
billty for any errors
that may appeH
o
n th1s manual. Information conta•ned here1n 1s subject to change
withoutnotoce
Advertisement
