Download Print this page

Mobility Sound PTT- Z Quick Start Manual

Advertisement

Quick Links

Federal Communication Commission
Interference Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/ TV
technician for help.
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. To maintain compliance with FCC
RF exposure compliance requirements, please
avoid direct contact to the transmitting antenna
during transmitting
RF Exposure Warning!
Please keep product 20cm away from your body
or bystander during the radio operation. The
typical handheld two-way radios were certified
under mobile usage condition
(i.e. keep 20cm away from the user body) and
use of such radio closer than 20cm may exceed
the US RF exposure limit and shall be avoided.
PTT- Z or PTT-U
PUSH-TO-TALK Specification
PTT-U2
PTT-Z
PTT-U3
Mobility Sound PTT- Z
Model No.: PTT- Z or PTT-U
Made in Taiwan
All other product or service names are the
property of their respective owners.
© 2014 Mobility Sound Technology Ltd,,
All Rights Reserved
PTT-U1

Advertisement

loading
Need help?

Need help?

Do you have a question about the PTT- Z and is the answer not in the manual?

Questions and answers

Summary of Contents for Mobility Sound PTT- Z

  • Page 1 (2) this device must accept any interference received, including interference that Mobility Sound PTT- Z may cause undesired operation. Model No.: PTT- Z or PTT-U This equipment complies with FCC RF radiation Made in Taiwan exposure limits set forth for an uncontrolled environment.
  • Page 2 Features . 2.4GHZ transceiver . -93dbm sensitivity in Bluetooth low energy mode v4.0 . TX Power -20 to +4dbm . RSSI (1db resolution) . ARM Cortex – M0 32 bit processor . Serial Wire Debug (SWD) . S100 series SoftDevice ready .
  • Page 3: Controls And Connection

    Controls and connection Velcro Fastener The Velcro fastener is used to secure the PTT-Z to your person or any other convenient location during use.
  • Page 4: Installing Or Replacing The Battery

    Installing or Replacing the Battery Installing or Replacing the Battery The PTT-Z uses one replaceable CR2032 coin cell type battery. The Z uses one replaceable CR2032 coin cell type battery. The first time you use rst time you use your PTT-Z, you will need to install a new battery you will need to install a new battery or power on the slide switch on the PCB.
  • Page 5 To change the battery: 1. Separate the two halves of the PTT-Z housing by securely holding the back cover and rotating the front cover in a counter-clockwise direction until the two halves come apart. 2. Locate the battery holder inside of the device. Remove the old battery from the battery holder if one is installed.
  • Page 6: Support And Warranty

    Mobility Sound warrants this product against defects in materials or workman-ship for a period of one year from the date of retail purchase. Mobility Sound will repair or replace a defective unit, at our option, without charge for parts or labor. The limited warranty is extended only to the original purchaser.

This manual is also suitable for:

Ptt-u