Subscribe to Our Youtube Channel
Related Manuals for SWIT FLOW10K Tx
Summary of Contents for SWIT FLOW10K Tx
- Page 1 SWIT ELECTRONICS CO., LTD. Model： FLOW10K Tx / FLOW10K Rx 10000ft/3km Wireless User Manual Please read this user manual throughout before using Ver： A...
- Page 2 All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners. Due to constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice.
-
Page 3: Safety Precautions
Safety Precautions Please follow the safety precautions before using. The following conditions are not covered by warranty. 1. Unauthorized repairs or other Unauthorized operations. 2. Inappropriate placement including but not limited to lighting, fire, exposure to rain, water or gas. 3. - Page 4 3000 meters transmission distance In open outdoor area, the effective transmission distance is approx. 3000 meters (line of sight). Wireless frequency The system adopts 5180~5220MHz and 5760~5820MHz Wireless frequency band （FLOW10K Tx） . Frequency Band and Frequency point CH00 5180MHz...
- Page 5 Remark: 1. The transmission distance may be different, and depending on surroundings, radio wave conditions, buildings, etc., the 3000 meters transmission distance may be not guaranteed in a complex environment. 2. The wireless transmission might be interrupted if there’ re other devices of 5Ghz wireless bandwidth used in the same location.
- Page 6 ⑾ Battery plate： Power supply via D & F & U model battery plate. Model D battery we recommend SWIT battery: S-8D98、 S-8D58 、 S-8D62 which is compatible with Panasonic CGA series: CGA-D54S/D28S、 VBD series SVW-VBD58； Model F battery we recommend SWIT battery: S-8972、...
- Page 7 SDI OUT DC 7-34V OFF/ON (10) ⑴ Handle ⑵ Battery plate： Power supply via V-mount battery. V-mount battery we recommend SWIT battery:： PB-M98S、 PB-S98S、 PB-S220S. ⑶ Adjustable tightening handle ⑷ Link： Wireless status indicator. ⑸ Video： Video signal indicator. ⑹ Power： Power status indicator.
- Page 8 SDI OUT DC 7-34V OFF/ON (14) (11) (12) (13) ⑾ SDI OUT： SDI signal output， standard BNC interface. ⑿ DC in： Support 7～34V wide voltage input. DC power input interface， 5.5mm （Outer diameter） /2.1mm(Inner diameter)， The polarity is inner positive and outer negative. ⒀...
- Page 9 4.OLED Display menu Initial interface （One-to-one mode） Initial interface （One-to-one mode） When no signal input， the transmitter is consistent When Transmitter and receiver video signal con- with the receiver display content. See Fig. 1 nection normal, the transmitter is consistent with the receiver display content.
- Page 10 Interface changing a ： Changing interface in transmitter via using joystick(left and right),see fig .7、 8、 9. b : Changing interface in receiver via using joystick(left and right),see fig .7、 9. FIRM- PREF. MULTI One to multi mode Firmware upgrade High quality mode WARE HIGH...
- Page 11 ⑵ Connecting SDI OUT interface of FLOW10K receiver with SDI IN interface of monitor or switcher. When using one-to-multi mode, every SDI OUT interface of receiver should be connected with SDI IN interface of monitor or switcher. ⑶ Switch on both FLOW10K transmitter and receiver, “Power” indicator light up， OLED screen show “WAIT�”...
- Page 12 8. The way to get the best effective of Wireless Transmission ⑴ Set the antenna on both transmitter and receiver vertically straight up.(See Fig.12)， Set the receiver faces the transmitter to extend the transmission distance and stabilize the transmission quality. Fig.12 ⑵...
-
Page 13: Troubleshooting
9. Trouble shooting If the receiver failed to output video correctly, the possible causes are as below; please find the solution from following chart: The receiving Possible causes Solution video Check power connection and switch on The transmitter or the receiver the transmitter and receiver Is not powered on Install the antennas properly and screw...
Need help?
Do you have a question about the FLOW10K Tx and is the answer not in the manual?
Questions and answers