Galaxy Audio PA6S Quick Start Manual

GAL A X Y AUDIO
Included Components
1.
PA6S x1
2.
IEC Power Cable x1
3.
SA-1 Stand Adapter x1
4.
Quick Start Guide x1
Setup
1
Connect power cable to PA6S, connect
other end to a power outlet.
6
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
2
Flip the power switch on.
1.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
7
The Pre Out provides a Line Level mix
of both channels.
3
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
2. 3.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6S. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
Stand Mounting
(Optional)
1
Attach the SA-1 to the mic stand, then
Lift the PA6S over the stand, align it up
with the hole.
4
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
4.
GAL A X Y AUDIO
Q uick Start Guide
Included Components
1. 1. 2. 3. 4.
PA6S x1
2. IEC Power Cable x1
3. SA-1 Stand Adapter x1
4. Quick Start Guide x1
Setup
1 2 3 4 5
Connect power cable to PA6S, connect Choose the input needed and for what For a balanced mic signal, plug the XLR For Balanced or Unbalanced Line Level, Connect a female XLR to the Thru
other end to a power outlet. channel(s) needed: male end of the cable into the XLR/1/4" plug the 1/4" cable into the XLR/1/4" output to feed the channel's XLR input
XLR/1/4" Combo Jack for mic, or Combo Input on the PA6S. For strong Combo Jack on the PA6S. to another device.
balanced/unbalanced line level. signals, engage the -20dB Pad Switch to
1/8" for stereo from a media player etc. prevent distortion.
Stand Mounting (Optional) Operation
6 7 1 2 1
For a stereo signal from an MP3 player, The Pre Out provides a Line Level mix Attach the SA-1 to the mic stand, then Bring the PA6S down onto the stand Ensure that both channels have their
attach 1/8" stereo cable into the Channel of both channels. Lift the PA6S over the stand, align it up gently until secure. levels lowered by turning counter-
2 1/8" input. with the hole. clockwise.
2 3 4 5 6
Flip the power switch on. Level control: turn clockwise to raise the EQ controls - Low/Mid/Hi: To increase the Reduce the Input Levels if the Clip LED Max. level is reached when the yellow
level. Turn counter-clockwise to lower low, mid, and high frequencies, turn the comes on. "Comp" light only flashes at peak levels.
the level. appropriate tone control clockwise. To If the light is on constantly, turn the level
decrease, turn counter-clockwise. controls down to avoid damage to the
PA6S.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6S.
2
Bring the PA6S down onto the stand
gently until secure.
5
Reduce the Input Levels if the Clip LED
comes on.
Quick Start Guide
5
Connect a female XLR to the Thru
output to feed the channel's XLR input
to another device.
Operation
1
Ensure that both channels have their
levels lowered by turning counter-
clockwise.
6
Max. level is reached when the yellow
"Comp" light only flashes at peak levels.
If the light is on constantly, turn the level
controls down to avoid damage to the
PA6S.