Ebelco 300-LED Installation Instruction Manual

Electromagnetic lock

Advertisement

Model
300-LED
Spec
Up to 300lbs
Static Strength
(Factory Tested)**
Dynamic Strength
12VDC / 24VDC
Voltage Input
Current Draw
330mA / 185mA
Dimension
(L)210 x (W)35 x (T)22 (mm)
General Installation
Door
Frame
EM Lock
Out Swing
Door
LS Bracket For
Out-Swing Door
Door
Frame
EM Lock
Out-Swing
Door
AH Bracket Fire Door Application
Door
Frame
Armature
Housing
Door
Out Swing
EM Lock
Armature Plate
24 VDC
12 VDC
Setting
Setting
12 / 24 VDC
Power Output
Hall Effect
Sensor Input
(Only for LED
Models)
Caution Against Changing
Factory Applied Settings !
Set the jumper position according to the power
input correctly before switch ON the power.
Notice:
All models are Recognized to:
UL 294 and ULC S533-15 : Standard for Access & Egress.
Models 800-S, 800-LED, 1200-S & 1200-LED are listed to:
UL 1034, Standard for Burglary-Resistant Electric Locking Mechanism.
UL 294, Access Control System Units
* Models are not listed in UL 1034
* * Value not verified by UL.
Remark: All drawing shown are for illustration purpose only.
Actual product may vary due to product enhancement.
Electromagnetic Lock
Installation Instruction Guide
(Intend for use in indoor dry location)
*
*
600-S
Up to 600lbs
(Factory Tested)**
N/A
12VDC / 24VDC
480mA / 240mA
(L)250 x (W)42 x (T)25 (mm)
Basic Installation Concept & Accessories
T Handle Allen Key
(Not include in package)
Fixing
Screw
Allen Wrench
General Installation Steps & Maintainance
1.
2.
3.
4.
LED Status:
5.
> Green = Locked
> Red = Released
> Off = No Input
(Only for LED Models)
6.
7.
8.
12 / 24 VDC
-
Power Input
N.O
9.
Hall Effect Sensor
N.C
Output
10. Typical wiring method which shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I,
(Only for LED Models)
C
11. It is recommended that to apply a light coat of silicon lubricant to the mating surface on a monthly
*
800-S
600-LED
600lbs (Factory Tested)**
500lbs (UL Verified)
N/A
510mA / 285mA
480mA / 240mA
(L)250 x (W)50 x (T)29 (mm)
Cable Wire
Armature
Screw
Anti Tamper
Nut
Rubber
Washer
Armature Plate
Close the door & position the template at the lock jamb side of the frame with a gap 10mm.
Mark & drill holes according to template indications.
Install the Armature Plate to the door.
Loosely tighten screw through the adjustable slot on mounting plate to the door frame as indicated on
installation template.
Make sure the mounting plate & armature align properly, then screw in the balance mounting screws.
Use allen wrench to unscrew anti tamper nut and install the lock by tighten the fixing screws on the
mounting plate. Pull cable wire through frame to lock housing.
Screw in the anti-tamper nuts to prevent unauthorized access and make sure to fully tighten the fixing
screw with proper tool "T" Handle Allen Key.
Connect the power wires accordance with NFPA 101 & all wiring to be completed inside protect area.
Safety Standard for Electrical Installations, Section 32.
basis to prevent rust.

Trouble Shooting

1. Sensor not functioning
- Improper attachment of electromagnet and
armature plate
- Modification of the PCB
2. Door not locked
- Incorrect wiring or no power from power supply
3. Reduced holding force
- Poor contact of electromagnet and armature.
- Be sure armature is loose enough that it can fully
contact electromagnet along the entire length.
- Mating surface is dusty or damaged.
- Improper input voltage or wire size.
1200-S
800-LED
50ft-lb
12VDC / 24VDC
510mA / 285mA
420mA / 210mA
(L)266 x (W)67 x (T)39 (mm)
12/24 VDC
Power
Mounting Plate
Self-tapping Screw
PCB Cover
Cover
Screw
Guide Pin
Sexnut Bolt
Metal
Washer

Performance Level

- Destructive Attack: Level I
- Line Security: Level I
- Standby Power: Level I
- Endurance 250,000 Cycles: Level IV
(Relay Source #2 & #3)
EISB-EMS-IG Ver.A Publish:11.3.2020
1200-LED
1200lbs (Factory Tested)**
1000lbs (UL Verified)
70ft-lb
12VDC / 24VDC
500mA / 265mA
U1 Bracket For
Glass Door
Door Frame
Glass
Door
EM Lock
Out-Swing
ZL Bracket For
In-Swing Door
Self-tapping Screw
Door
Frame
EM Lock
Door
In-Swing
DSU Bracket For
Glass Frame & Glass Door
Glass
Frame
EM Lock
In-Swing
Glass
Door
1-2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 300-LED and is the answer not in the manual?

Questions and answers

Summary of Contents for Ebelco 300-LED

  • Page 1 Electromagnetic Lock Installation Instruction Guide (Intend for use in indoor dry location) Model 800-S 1200-S 1200-LED 300-LED 600-S 600-LED 800-LED Spec 1200lbs (Factory Tested)** Up to 300lbs Up to 600lbs 600lbs (Factory Tested)** Static Strength (Factory Tested)** (Factory Tested)** 500lbs (UL Verified)
  • Page 2 Basic Bracket Installation Guide Installation Template Door Frame Template Door Door Out Swing Out Swing Door Fold the Installation Template Close the door & position the Mark & drill holes according to template at the lock jamb side of Note: Installation Template only applicable for template indications.

This manual is also suitable for:

600-s600-led800-s800-led1200-s1200-led

Table of Contents