Ebelco 300-LED Installation Instruction Manual

Model
300-LED

Spec

Voltage Input 12VDC / 24VDC
Current Draw 330mA / 185mA
Dimension
(L)210 x (W)35 x (T)22 (mm)
General Installation
Door
Frame
EM Lock
Out Swing
Door
DSU Bracket For
Glass Frame & Glass Door
Glass
Frame
EM Lock
In-Swing
Glass
Door
LS Bracket For
Out-Swing Door
Door
Frame
EM Lock
Out-Swing
Door
12 VDC 24 VDC
Setting Setting
12 / 24 VDC
Power Output
Hall Effect
Sensor Input
(Only for LED
Models)
Caution Against Changing
Factory Applied Settings !
Set the jumper position according
to the power input correctly before
switch ON the power.
Remark: Drawing maybe differ from actual product.
Copyright E.I.S.B. All Right Reserved.
EISB-EMS-IG Ver.A Publish:18.1.2019
Electromagnetic Lock
Installation Instruction Guide
(Intend for use in indoor dry location)
600-S
12VDC / 24VDC
480mA / 240mA
(L)250 x (W)42 x (T)25 (mm)
Basic Installation Concept & Accessories
T Handle Allen Key
Fixing Screw
x2
Allen Wrench
General Installation Steps & Maintainance
1. Drill the armature plate holes in the door using the sticker template provided.
2. Attach the armature plate to the door with the hardware provided as per the illustration.
3. With the door closed, mark the door frame at the edge of the armature in order to properly align the
LED Status:
> Green = Locked
electromagnet to the armature.
> Red = Released
> Off = No Input
4. Attach the mounting plate to the door frame using the self-tapping screws provided.
(Only for LED Models)
5. Insert the wires through the hole in the mounting plate and into the electromagnet unit.Attach the
electromagnet unit to the mounting plate with the Allen head fixing screw.
12 / 24 VDC
6. Screw in the anti-tamper nuts to prevent unauthorized access and m ake sure to fully tighten the fixing
-
Power Input
screw with proper tool "T" Handle Allen Key.
N.O
Hall Effect Sensor
7. Connect the power wires accordance with NFPA 101 & all wiring to be completed inside protect area.
N.C Output
(Only for LED Models)
8. Typical wiring method which shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I ,
C
Safety Standard for Electrical Installations, Section 32.
9. It is recommended that to apply a light coat of silicon lubricant to the mating surface on a monthly basis

Trouble Shooting

1. Sensor not functioning
2. Door not locked
3. Reduced holding force
600-LED
12VDC / 24VDC
510mA / 285mA
(L)250 x (W)42 x (T)25 (mm)
Cable Wire
Armature
Screw
Anti Tamper
Nut x2
Rubber
Washer
Armature Plate
Align the mounting plate with the mark from the previous instruction.
to prevent rust.
- Improper attachment of electromagnet and armature plate
- Modification of the PCB
- Incorrect wiring or no power from power supply
- Poor contact of electromagnet and armature.
- Be sure armature is loose enough that it can fully contact
electromagnet along the entire length.
- Mating surface is dusty or damaged.
- Improper input voltage or wire size.
1200-S
12VDC / 24VDC
420mA / 210mA
(L)266 x (W)67 x (T)39 (mm)
12/24 VDC
Power
Mounting Plate
Self-tapping Screw
PCB Cover
Cover
Screw
Guide Pin x2
Sexnut Bolt
Metal
Washer
Performance Level
- Destructive Attack: Level I
- Line Security: Level I
- Standby Power: Level I
- Endurance: Level IV
(Relay Source #2 and #3)
1200-LED
12VDC / 24VDC
500mA / 265mA
(L)266 x (W)67 x (T)39 (mm)
U1 Bracket For
Glass Door
Door Frame
Glass
Door
EM Lock
Out-Swing
ZL Bracket For
In-Swing Door With Cover
CSK M8 x16
Door
Frame
EM Lock
M4 Set
Screw
Door
In-Swing
ZL Bracket For
In-Swing Door
Self-tapping Screw
Door
Frame
EM Lock
P/H MC Screw
Door
M4 x 8
In-Swing
1-2