Viking UNDERCOUNTER/FREESTANDING WINE CELLAR Use & Installation Instructions Manual page 5

FOR 3-1/2" TOE KICK
(COVERS THE ENTIRE DOOR EXTRUSION)
(RIGHT HINGE)
1/4" X 3/8" Deep hinge screw clearance hole. Locate and drill using door hinge hole
after the door has been aligned to the unit and when the wood is positioned on door
3 7/32"
(8.1 cm)
Min. 5/8" (1.7 cm)
Max. 3/4" (1.9 cm)
14 5/16"
(36.4 cm)
15/32"
(1.2 cm)
15/32"
(1.2 cm)
Dia. hole
(1.8 cm) TYP
13/16" (2.1 cm) counterbore 7/16"
1 23/32" (4.4) cm min. width to cover
door extrusion
30 5/16"
(77.0 cm)
Pre-drilled pilot holes -
8 places
Mounting surface
(non-face) side
1/4" X 3/8" Deep hinge screw clearance hole. Locate and drill using
door hinge hole after the door has been aligned to the unit and when
the wood is positioned on door
Mounting surface
(Non-face) side
7 5/32" (18.2 cm)
23/32"
7 13/16"
(19.8 cm)
(1.1 cm) deep TYP
15 5/32"
(38.5 cm)
TYP
22 1.2"
(57.2 cm)
23/32"
TYP
(1.8 cm)
TYP
Mounting surface
(non-face) side
8
Attaching the Wood Frame to the Door - DFUW Models
1. If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove
the door by angling the door off of the bottom hinge pin.
2. Install the supplied lock body into the wood panel. Secure the lock body by using the supplied 15mm lock
retaining nut. Screw the lock retaining nut on the lock body's threaded section. Make sure the lock's key slot is
vertical, then tighten the nut with a deep well socket.
3. Peel back the door gasket to expose the screw holes and lock location hole.
4. Set the wood frame flush to the front of the door in the desired location. Clamp the wood frame to the door if
necessary. Check to make sure the back of the lock in the wood frame lines up with the hole in the door.
5. Insert the wood screws through the back of the door into the pilot holes in the wood frame and tighten.
6. Assemble the door lock's phillips head screw, the lock extension, and lock cam. Mount them to the back of the
lock body. The cam should be oriented vertically. Tighten the phillips head screw to secure the lock assembly.
7. Reinstall the door gasket by pressing into the door channel. Make certain the corners are inserted fully. Insert the
key into the lock and make sure the lock operates properly
8. Install the door to the unit. Use the supplied plastic washer as shown in the figure below.
9. Realigning the door may be necessary. Any final door adjustments can be made using a 1/8" allen head driver to
adjust the door's hinges. (See figure below)
10. Attach the door light striker plate as shown using the 5/16" hex or phillips head screws provided. Make certain the
light is able to turn on and off when the door is opened and closed.
11. Attach the door to the unit by reversing step number 1 above.
12. Insert the key into the lock and verify that the lock cam works properly with the catch bracket on the cabinet front.
Hinge Hardware Installation
Details
CAUTION CAUTION
Door can become Door can become
disengaged if washers disengaged if
are not installed. washers are not
installed.
Wood
Frame
Door Hinge
Shoulder bushing
3/4" OD x 7/16"
ID Washer
3/4" OD x 1/4" ID
CAUTION Washer
Door may not swing properly
(3) Nylon hardware
if all nylon components are
components at
not installed as shown
bottom hinge
Bottom Hinge Cover Top Hinge Cover
(2) Nylon
Magnetic door gasket
hardware
Cabinet components at
Hinge top hinge
for frame wood screws
5/8"x 7/32" ID washer
Shoulder
bushing
Door Hinge
Rear of Door
Wood Frame
1/8" allen head screws for hinge
adjustment
Door hinge adjustment
screws
Attached wood
frame
9
3/8" clearance holes
- 8 holes
Door light striker plate
Bottom of
door