Related Manuals for Harmopool QBIC
Summary of Contents for Harmopool QBIC
- Page 1 Swimming pool heat pump QBIC (Model ZVWX5010, ZVWX5020, ZVWX5030) Instruction manual Imported by: Zwembad BVBA Industrieweg 9 3190 Boortmeerbeek België www.harmopool.eu...
-
Page 2: Table Of Contents
Table of contents Table of contents ........................2 Introduction ..........................3 Characteristics ........................3 Specifications ........................... 4 Performance data ........................ 4 Dimensions of the heat pump ..................... 5 Installation ..........................6 Installation items ......................... 6 Location ..........................6 Distance ..........................7 Installation of the check-valve ..................... -
Page 3: Introduction
Introduction In order to provide our customers with quality, reliability and versatility, this product has been made to strict production standards. This manual includes all necessary information about installation, debugging, discharging and maintenance. Read the manual carefully before you open or maintain the unit. The manufacturer of this product cannot be held responsible for injuries or damage, as a result of improper installation, debugging or unnecessary maintenance. -
Page 4: Specifications
Specifications Performance data Unit Model ZVWX5030 ZVWX5010 ZVWX5020 12,0 14,0 Heating Capacity in A27/W27°C* 39780 46580 BTU/h 30600 Heating Capacity in A15/W26°C* 27880 31280 BTU/h 22100 Power Input 1,63 Maximum Pool Volume 12,2 Running Current COP at A15/W26 COP at A27/W27 Min air temperature Deg C Power Supply... -
Page 5: Dimensions Of The Heat Pump
Dimensions of the heat pump Model ZVWX5010 ZVWX5020 Size (mm) ZVWX5030 A 670 G 101 F 250... -
Page 6: Installation
Installation Installation items The factory only provides the heat pump unit; the other items that are mentioned in the illustration are to be provided by the user or installer. Attention! ○ All feeding of chemicals to the pool water has to be done downstream of the heat pump. ○... -
Page 7: Distance
Distance Install the heat pump as close to the swimming pool as possible to minimize the loss of heat through the piping. Put it on a solid base and place the rubber blocks under the heat pump to eliminate vibrations. Normally, the pool heat pump is installed within a 7,5 meter radius of the pool. -
Page 8: Configuration
Configuration Note: the above piping connection is only an example for demonstration. Installation of the bypass With the bypass set correctly, your heat pump will deliver its best performance. The bypass has to be built as shown below: ○ Install the bypass with all 3 valves entirely open ○... -
Page 9: Electrical Wiring
Electrical wiring For the electrical connection of the heat pump use the connectors L, N and grounding. Verify the local power supply and the operating voltage of the heat pump. It is recommended to use a separate circuit breaker (slow type – D curve) for the heat pump together with the proper wiring characteristics. -
Page 10: Start-Up Procedure
Start-up procedure After the installation is completed, you should follow these steps. 1. Set the by-pass valve 1 entirely open. Turn on your filter pump. Check for water leaks and verify flow to and from the pool. 2. Turn on the electrical power supply to the unit and turn the unit ON with the switch. Slightly close valve 1 until the heat pump starts. -
Page 11: Guidelines
Guidelines Water chemistry Special attention should be paid to the chemical balance of the pool water. The values should always stay within the following limits: Free chlorine (mg/l) TAC (mg/l) Salt (g/l) Attention! ○ Failure to keep the swimming pool water between above limits will invalidate the warranty ○... -
Page 12: Spring Start-Up
4. Turn on the electrical power to the heat pump at the main breaker panel. Owner inspection The QBIC heat pumps are designed and constructed to provide long performance life when installed and operated properly under normal conditions. Periodic inspections are important to keep your heat pump running safely and efficiently through the years. -
Page 13: Lcd Controller Display
LCD Controller Display Setting step 1. Under running status, press to adjust the temperature. 2. Standby status: Press M 5 seconds,get a sound “B” ,LCD display will show “0" “27” “SET” to enter cooling temp. setting,press to alter cooling temp. Press “SET”again to confirm. Press M again “1””... -
Page 14: The Functions Of Controller Display
The functions of controller display Under running status, press to adjust the temperature. Setting operation parameter o Under standby status, press M button 5s to enter Operation Parameter setting interface. o Press M again to start setting (parameter from 00-G,see the Operation Parameter Table). o Under parameter setting, press to set data. - Page 15 How to know the current status Under running status , press M for 5 seconds to check the current status of the unit! You can check water-in/water out temp, condenser temp and ambient temp. Please note no motion on the display for 10s. The LCD will display water-in/water out temp/(under running)or ambient temp.(unit stops).
-
Page 16: Operation Data Setting Table
Operation data setting table This data setting table is suit for heat pump with heating and cooling function. If heat pump without cooling function, parameter 0,2,3,4,5 will not work. Digit Meaning Range Default Adjust (yes/no) Return water temp. 8-28°C 12°C Setting (cooling mode) Return water temp. -
Page 17: Maintenance And Inspection
Maintenance and inspection Maintenance o Check the water supply to the unit and the releaser often. Low water flow and air entering into the system should be avoided, as this will diminish the units’ performance and reliability. You should clean the pool/spa filter regularly to avoid damage to the unit as a result of the dirty or clogged filter. -
Page 18: Problems And Solutions
Problems and solutions Malfunction Controller Reason Resolution display Water in temp. PP 01 The sensor is open or Check or replace a new sensor sensor failure short circuit Water out temp. PP 02 The sensor is open or Check or replace a new sensor sensor failure short circuit Coil sensor failure... -
Page 19: Wiring Diagram
Wiring diagram Model ZVWX5010 - ZVWX5020 - ZVWX5030... -
Page 20: Warranty
Warranty...