Related Manuals for LNS WS Series
Summary of Contents for LNS WS Series
- Page 1 OIL MIST COLLECTORS Series WS mod. 170 - 330 - 700 - 1020 - 1250 INSTRUCTION AND INSTALLATION MANUAL...
-
Page 2: Table Of Contents
6.7.2 Disposal of the unit ..........................26 7. Spare parts ............................ 27 7.1. Spare filters reorder codes ....................... 27 7.2. Complete Spare List ......................... 28 © LNS FOX Instruction manual series WS (USA) pag. 2 of 28 - rev. 06-2014... -
Page 3: General Information
Additional safety indications are described on the labels placed on the unit. “Personal safety – integrity of the unit” LNS FOX is not liable for possible injuries to people and/or damages to objects caused by negligence of non observance of any safety direction. -
Page 4: Main Safety Prescriptions
Temperature: from 41 to 104 Fahrenheit • Relative humidity of the environment: from 30 to 85% • Relative humidity on the unit’s inlet: from 30 to 98% © LNS FOX Instruction manual series WS (USA) pag. 4 of 28 - rev. 06-2014... -
Page 5: Identification And Specifications
• Maximum concentration of the oil mist: 360 mg/m3 “integrity of the unit” LNS FOX declines any possible responsibility for damages to the unit due to use under conditions different than the ones above specified. 1.4. Identification and specifications Technical data and identification of the unit are listed on the serial number tag (located on the back of the unit by the power inlet). -
Page 6: Warranty
The warranty does not apply in case of damages caused by improper and/or not according to this manual use of the unit. Every attempt to repair the unit by personnel not authorized by LNS Italia will result in a reduction or cancellation of the warranty. -
Page 7: Description And Features Of The Unit
“Personal safety – integrity of the unit” Before unlocking latches verify that the unit is securely installed on the 4 anti vibration mounts. f) Eye bolt for lifting the unit © LNS FOX Instruction manual series WS (USA) pag. 7 of 28 - rev. 06-2014... -
Page 8: General Characteristics
WS 170 WS 330 WS 700 WS 1020 WS 1250 Shaft height Frame N° poles Protection index IP Isolation class Voltage/frequency V/Hz] 230-400-460/60 Power [hp] © LNS FOX Instruction manual series WS (USA) pag. 8 of 28 - rev. 06-2014... -
Page 9: Dimensions (Inches)
14,29 x 15,55 x 23/64" WS 700V 20,67 23,31 33,15 20,98 9,41 7,01 0,98 1,65 3,54 10,2 18,82 x 18,82 x 23/64" Fig. 6 a Dimensions © LNS FOX Instruction manual series WS (USA) pag. 9 of 28 - rev. 06-2014... -
Page 10: Installation
Furthest away from working area. Minimizing ducting length (in order to reduce pressure drop is it reccomended, use suction tube lenght max of 15 feet.) © LNS FOX Instruction manual series WS (USA) pag. 10 of 28 - rev. 06-2014... - Page 11 Connect the extraction duct with the flange adapter fitted on the machine using a piece of flexible tubing of proper diameter and length. Secure both ends of the duct with metal clamps. © LNS FOX Instruction manual series WS (USA) pag. 11 of 28 - rev. 06-2014...
-
Page 12: Trap With Use Of Trap Bracket (Included In The Supply)
Fig.10d Fig.10e Fig.10f Secure the drainage hose Bracket for siphon trap Trap with use of dedicated bracket Fig.10g Fig.10h - Secure the ring with Fig.10i © LNS FOX Instruction manual series WS (USA) pag. 12 of 28 - rev. 06-2014... -
Page 13: Trap With Immersion Of The Tube In A Container Of Liquid
In this case make sure that the tube is permanently immersed in the liquid in order to ensure the perfect drainage of the liquid re-condensed Fig. 10 m) © LNS FOX Instruction manual series WS (USA) pag. 13 of 28 - rev. 06-2014... -
Page 14: Electrical Connections
(Fig. b) Removal of control panel box (Fig. c) electrical connection (Fig. d) Setting of thermal switch (Fig. e) Tight gland (Fig. f) Impeller rotating direction © LNS FOX Instruction manual series WS (USA) pag. 14 of 28 - rev. 06-2014... -
Page 15: Electrical Connection For Electric Motor With 9 Wires
3,31 WS 1020 2.4(1,80) < 6,76 6,76 2.4(1,80) <3,91 3,91 3.5 (2,6) < 4,29 4,29 WS 1250 3.5 (2,6) < 9,1 3.5 (2,6) <5,26 5,26 © LNS FOX Instruction manual series WS (USA) pag. 15 of 28 - rev. 06-2014... -
Page 16: Unit's Operation
One example is an application with presence of large amounts of metallic dust. In these cases make sure that verify conditions of the prefilter more often than indicated on the maintenance section table Upon request the mist collector can be equipped with additional monitoring devices. Please contact LNS Italia sales department for additional information. -
Page 17: Maintenance
If the drainage slotes are obstructed, remove and clean impeller case as described in “Centrifugal stage Maintenance”. If seal is damaged or broken it must be replaced as described in “Seals maintenance” © LNS FOX Instruction manual series WS (USA) pag. 17 of 28 - rev. 06-2014... -
Page 18: Emulsion Version Prefilter
(only for WS 250-1500- structure 2000) l) Reposition metal screen m) close down top n) tight 2 external knobs 6.2.1.b Oil version prefilter © LNS FOX Instruction manual series WS (USA) pag. 18 of 28 - rev. 06-2014... - Page 19 If that is the case verify the cause, take care of the problem and close the unit. © LNS FOX Instruction manual series WS (USA) pag. 19 of 28 - rev. 06-2014...
-
Page 20: Main Filter (Stage 3) Maintenance For Oil And Emulsion Versions
Unscrew knob and remove filter • Unscrew nuts securing impeller case/drainage ring • Only if necessary proceed with the removal of the impeller (see cleaning of the impeller) © LNS FOX Instruction manual series WS (USA) pag. 20 of 28 - rev. 06-2014... -
Page 21: Cleaning Of The Impeller
Reinstall impeller case and drainage ring making sure that nuts are properly tight. 18a) remove impeller case and b) removal of impeller c) impeller cleaning drainage ring © LNS FOX Instruction manual series WS (USA) pag. 21 of 28 - rev. 06-2014... -
Page 22: Seals Replacement
Removal • Remove the impeller as described in the general cleaning section • Unscrew the 4 screws securing the cover of the control panel box © LNS FOX Instruction manual series WS (USA) pag. 22 of 28 - rev. 06-2014... -
Page 23: Torque Settings
Integrity of structural parts relative to the motor support plate • Tighten of nuts securing the motor • Tighten screw securing impeller • Integrity and efficiency of gas charged springs © LNS FOX Instruction manual series WS (USA) pag. 23 of 28 - rev. 06-2014... - Page 24 © LNS FOX Instruction manual series WS (USA) pag. 24 of 28 - rev. 06-2014...
-
Page 25: Troubleshooting
Verify possible causes and solve the problem. In case of absorbed current is above the motor causing a short proceede with the replacement nominal value of the motor. © LNS FOX Instruction manual series WS (USA) pag. 25 of 28 - rev. 06-2014... -
Page 26: Disposal
In order to obtain the maximum reuse of the raw materials we strongly suggest to delegate this dismissal of the unit to a waste disposal specialized company © LNS FOX Instruction manual series WS (USA) pag. 26 of 28 - rev. 06-2014... -
Page 27: Spare Parts
350006000 350007000 350008000 Main filter (3° stage) 350146000 350147000 350148000 350149000 350150000 350105000 350106000 350107000 350108000 Absolute filter (optional) Activated Carbon refill (optional) 350109000 350110000 © LNS FOX Instruction manual series WS (USA) pag. 27 of 28 - rev. 06-2014... -
Page 28: Complete Spare List
350093000 350093000 350093000 350095000 350095000 LOWER CASE 350141000 350097000 350098000 350099000 350100000 SEAL 350143000 350113000 350114000 350115000 350116000 DRAINAGE RING 350142000 350101000 350102000 350103000 350104000 © LNS FOX Instruction manual series WS (USA) pag. 28 of 28 - rev. 06-2014...