Download Print this page

SkyLink SkylinkHome Smart Button GB-434 Manual

Garage door control

Advertisement

Quick Links

TM
Smart Button
Garage Door Control
1. INTRODUCTION
Congratulations on your purchase of the SkylinkHome
The Smart Button
TM
is designed to work with SkylinkHome
as TC-434 series, TB-434 series, and more to operate the Garage Door
Opener. In this kit, you will find the following:
Smart Button
GB-434
2. INSTALLATION
Unplug the power cord of your garage door opener
before installation to ensure power is not connected.
WARNING
1. Open up the "Easy Clip
TM
" and place it underneath
the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires
are placed properly inside the channels of the
TM
"Easy Clip
".
NOTE:
Ensure the ribbon wires
are not twisted but laid
flat inside the clip.
If your wall button ribbon wires
are not the AWG#22 or #24 or
the same kind as shown in the
diagram, please refer below (4)
or visit our website
www.skylinkhome.com for
more information.
3. Press and lock the clip by snapping it together. The included Crimper
helps you lock the "Easy Clip
lock the cover using this Crimper until you hear a "click".
4. If the "Easy Clip
TM
" cannot clip with the wires from your wall button, cut
TM
off the "Easy Clip
" then connect two wires from the Smart Button
to the wall button.
a) Dismount the existing wall button from the wall.
b) Connect the 2 wires from the Smart Button
GB-434 to your existing wall button. Polarity
does not matter, so simply pick one wire from
the Smart Button
TM
and connect it to one of the
screw terminals on your wall button. Connect
the 2nd wire to the other screw terminal.
c) Mount the wall button back.
Model GB-434
TM
Smart Button
TM
remote such
Double Sided Tape
TM
Crimper
Wall Button
Ribbon Wires
Press / lock
Ribbon Wires
TM
". Close the cover and press down to
TM
TM
.
5. If the wall button wires are hidden inside the
wall, please connect the "Easy Clip
the exposed wires attached to the
terminals of the garage door
opener.
6. Power up the garage door opener, the red LED on the Smart Button
GB-434 should keep flashing slowly within 2 minutes.
If the Smart Button
Button
TM
GB-434 has been connected to the wall button's wires
for 2 minutes, your garage door opener is probably too old.
However, the Smart Button
adapter (purchased separately). Please contact
Skylink
®
to purchase the adapter.
Rating of the transformer:
12V DC, 100mA
Diameter of DC plug : 3.5mm
Easy Clip
TM
7. Secure the SmartButton
Note: Do not cut the antenna! Straighten up the antenna to improve
signal reception.
Note:
After installation of the "Easy Clip
TM
Button
GB-434 to another place, please open the "Easy Clip
unlocking the two buckles with a screw driver, and remove it from the
wires. Do not re-use the "Easy Clip
If the red LED flashes slowly, the Smart Button
is in standby mode. When a valid remote control signal is
received, it will open / close the garage door.
Press the programmed button on the remote control
or Smart Button
garage door.
Programming
Learn additional remote controls
Smart Button
To learn additional remote controls, follow the
instructions below:
1. Press the learn button on the side of the GB-434.
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
3. Within 30 seconds, press the button on the remote
control you would like to program.
4. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
5. You may now operate the garage door opener
with this remote control.
TM
Erase remote controls
To erase unwanted remote control(s)from the memory of Smart Button
GB-434, first erase all remote controls, then learn the one(s) you would
like to keep.
To erase remote control(s), follow the steps below:
1. Press and hold the learn button for approximate 10 seconds.
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. Release the learn button.
3. You have erased all the remote controls programmed to the Smart
Button
TM
2. INSTALLATION (CONT)
TM
" to
TM
GB-434's red LED does not flash after the Smart
TM
will still work if you plug in an
TM
GB-434 properly with the mounting accessories.
TM
", if you want to re-install the Smart
TM
", refer to Step 4 to re-install it.
3. OPERATION
TM
GB-434, it will open / close the
TM
GB-434 can learn up to 10 remote controls.
GB-434.
TM
TM
" by gently
TM
GB-434
LED
OPEN /
CLOSE
Button
Antenna
LED
Learn Button
TM

Advertisement

loading

Summary of Contents for SkyLink SkylinkHome Smart Button GB-434

  • Page 1 2. INSTALLATION However, the Smart Button will still work if you plug in an adapter (purchased separately). Please contact Skylink ® to purchase the adapter. Unplug the power cord of your garage door opener before installation to ensure power is not connected.
  • Page 2 - find out the up-to-date specifications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difficulty getting products to work, please: 1. visit our FAQ section at www.skylinkhome.com, or 2.