Advertisement
AVMW
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water!
6.
Clean only with dry cloth!
7.
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other devices (including amplifiers) that
produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the device.
11. Only use attachments/accessories specified by the
manufacturer. System requires: UL listed Class 2, EPBU
category power supply rated at 24VDC/2.5A (provided with
AVM1).
12. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid
as been spilled or objects have fallen into the device, the
device has been exposed to rain or moisture, does not
operate normally, or has been dropped.
2
WARNING:
Class 2 wiring must be used.
WARNING:
Make all wiring connections prior to AC
connections and power up.
WARNING:
To reduce the risk of fire or electric shock, do
not expose this device to rain or moisture. Device shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as glasses or vases, shall be placed on the
device.
WARNING:
Input boxes MUST be installed in provided
electrical outlet boxes!
WARNING:
EMT, rigid or flex conduit may be required for
ceiling or wall isntallations, to meet local building codes or
authority having jurisdiction (AHJ) requirements.
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer's responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
Specifications and Requirements
RF Wireless Receive/ Transmit Performance (AVMW):
• (2) RF Receive channels with automatic 'secure link selection.
• RF antenna coverage 40 foot radius / 80 foot diameter nominal X-Y-Z
axis.
• RF Frequency hopping modulation in 2.4GHz and 2.5GHz ISM
band.
• 802.11 WiFi interference protection.
• GSM/CDMA cell phone interference immune.
• RF data transmit speed up to 2Mps with audio latency delay
<2msec.
• Signal-to-Noise >55dB.
• Sensitivity >80dBm.
• Audio Frequency 200Hz to 8KHz @ 16k sample rate 16 bit res-
olution.
• Audio Distortion THD <1% at 1KHz.
• Mono or Stereo operation with AVMA (AVxHM or AVxLM re-
ceiver headphones).
• Visual status LED's (Blue / Red).
• Soft push button channel On / Off.
• IrDA secure pairing to Headset, Microphone, Headphone in <
10 seconds.
• FCC Part 15 Class B.
• Rechargeable batteries are Lithium Ion Polymer and NiMH capable of
1000+ charges, 100% Fast recharge in (90) minutes typical,
50% charge in (30) minutes.
• Battery chargers with 6v wall power supply are UL / Energy
Star rated.
Power Efficiency
<80% at 25W 4W, <85% @ 8W, <90% at 10W 4W, <95% @ 8W
Power Consumption
32W / 9.5 btu @ 120VAC, 130ma nominal in 'Sleep' mode.
Operating Temperature
-10° to 40°C, 14 to 104°F
Storage Temperature
-20° to 65°C, -4 to 149°F
Mains Input Power
100-240VAC, 50-60Hz / Energy Star Rated
Input Power (to AVM1)
24VDC/2.5A regulated switching wall supply, UL1310 Class 2,
Energy Star, FCC, CUL, CE listed (provided).
Output Power (from AVM1)
25W Peak 4W per channel 12W RMS continuous 4W per chan-
nel.
Installation Instructions
Advertisement
