Summary of Contents for TCO ICon Pro
- Page 1 ICon Pro - user manual TCO Sp. z.o.o. Tyniecka 126C, 30-376 Krakow, Poland T +48 12 268 3218 E hello@thecleanair.eu I www.iconairhealer.eu...
- Page 2 Distributor address and contact data for replacement filters: Original user manual, written in the English Language TCO Sp. z o.o. Tyniecka 126C, 30-376 Krakow, Poland T +48 12 268 3218 E hello@thecleanair.eu I www.iconairhealer.eu Model: ICon Pro Date: 25/03/2020 Product code: ICon.2020.01…..
-
Page 3: Preface
The ICon Pro is easy to use when you follow the instructions. Please read the user manual carefully. Become familiar with the correct operation and maintenance procedures. Store the manual in a safe place. The manual is an essential part of the ICon Pro and must be handed over to the new owner on the upon resale or exchange. -
Page 4: Reading Guide
Reading guide The following symbols and terms are used throughout this manual to alert the reader to safety issues and important information: Symbol Term Explanation WARNING Indicates a hazardous situation which, if the safety instructions are not followed, can lead to injuries of the operator or bystanders, light and/or moderate damage to the product or the environment. -
Page 5: Table Of Contents
Content Preface ..................................3 Purpose of the user manual ............................ 3 Target audience ..............................3 Operators of the ICon Pro ............................3 Reading guide ................................4 Introduction ..............................7 Intended use of the product ........................7 Non-intended use of the product ......................8 Lifespan .............................. - Page 6 Replace the main HEPA filter ....................... 27 Recommended additional cleaning ..................... 28 Ordering replacement filters ....................... 28 Service interval UV-lamps ........................29 Trouble shooting ............................30 Decommissioning and disposal ........................31 Attachments ..............................32 10.1 Technical specifications ........................32 General specifications ..........................32 Performance ..............................
-
Page 7: Introduction
1 Introduction The ICon Pro is a safe and easy to use machine. This manual helps you to get started and explains the operation and maintenance procedure. You will be surprised how fast and effective the ICon Pro is in improving the indoor air quality. -
Page 8: Non-Intended Use Of The Product
, this operation is possible and doable only by your specialized service provider. 1.4 Modifications It is not permitted to make modifications to the design and construction of the ICon Pro without consultation and written permission from the manufacturer. This affects the warranty, see section... -
Page 9: Specifications
1.5 Specifications Figure 1 Product (body unit): 1273*684*334 mm Weight: 72 kg Control panel on front of unit: Transport wheels:... -
Page 10: Warranty
1.7 Identification Each ICon Pro has a unique identification number that can be found on the back side of the unit, in the left lower corner. Your TCO partner needs this number when you order parts. -
Page 11: Description
2 Description The ICon Pro combines state-of-the-art air purifying technologies in one, easy to set up stand-alone unit. The ICon Pro consists of: Figure 3 LED indicators. Display. Operation knob. Locking knobs of main HEPA filter compartment lid. Main HEPA filter compartment. Attached to the inside of the compartment panel you will find a 2.5 Allen wrench, to be used for opening the panel of the pre-filter compartment. -
Page 12: Working Principle
RJ socket for ethernet connection (for trained user only). ATTENTION It is advisable that the RJ ethernet connection is used by IT advanced users only and/or by trained operators. Ask your ICon Pro authorized supplier for support in setting the web access to ICon Pro. -
Page 13: Safety
Improper use can cause harm or void the manufacturer’s warranty. 3.1 General safety instructions The ICon Pro is an electrical appliance. Please read the safety instructions before use and take the necessary precautions to reduce the risk of fire, electric shock or injury. -
Page 14: Assembly And Installation
The ICon Pro does not require assembly. The pre-filter and main HEPA filter are pre-installed. CAUTION The ICon Pro unit is heavy. Do not try to carry and/or move the unit by yourself. You should always use someone's help. 5.1 Unboxing... -
Page 15: Unboxing Your Icon Pro
Inside you will see the honeycomb paper boards protecting your ICon Pro. Remove the front honeycomb paper board. • You will see your ICon Pro as shown in Figure 7. Remove the left and right honeycomb paper boards (Figure 7, pos. 3 and 7). -
Page 16: Operation
6 Operation 6.1 Before you start Carefully select the best location for the ICon Pro for the best purifying results. In an environment with heavy polluted air you may consider the use of more than one unit in the same room. -
Page 17: Boost Function
6.3 Boost function The ICon Pro is equipped with a boost function. The boost function can be used in spaces where the reduction of volatile organic compounds (VOC) and microbiological contamination has a higher priority than dust level (PM) reduction. -
Page 18: Control Panel
ATTENTION After you turn on your ICon Pro unit and before you start operations, always set your date and time. See Settings menu on page 23. The control panel consists of: •... -
Page 19: Fan Menu
Fan speed selection depends on a few factors. The main factor is the contamination level and room size of the room in which the ICon Pro is used. The bigger the room and the higher the contamination level, the higher the fan speed should be set. Always do care about the room users' comfort. -
Page 20: Schedule Menu
This menu allows you to configure the automatic schedule for fan operation. To make use of this Schedule menu the ICon Pro Fan mode has to be set to Automatic, see 6.4.2 Fan menu on page 19. In automatic mode, you have to define the working sequence for each day and every hour in each day. -
Page 21: Sensors Menu
When pressure sensors detect the pressure drop that occurs when the main HEPA filter needs to be replaced, the ICon Pro sounds an alarm and an error message is visible. More information on this you will find in the List of Status messages on page 24. -
Page 22: Lamps Menu
Displays the cumulative operating time of the UV-lamps in the neutralization chamber. The ICon Pro is designed to deliver the best results in neutralization with UV lamps lifespan of 4 years, when operating 24/7. So you don't have to worry about it for a long time. The life time of the lamps will vary when the boost function is used. -
Page 23: Settings Menu
The settings menu contains a variety of data mainly to be used by the service technician. Some ICon Pro users may want to use these advanced options. It is advisable though that your ICon Pro supplier sets all parameters in order to avoid mistakes. -
Page 24: Status Menu
6.4.7.1 Status When an error occurs, the ICon Pro sounds an alarm and the red LED indicator (on the right side of the control panel) is lit. Check the Status menu for information on the errors that occurred 6.4.7.2 List of Status messages •... -
Page 25: Maintenance
• Always switch off and unplug the unit before replacing the pre-filter filter. • Always use the replacement filters recommended by your ICon Pro supplier. 1. Unscrew the Allen screws (4x - Figure 17, pos.4) of the pre-filter compartment panel (Figure 17, pos. - Page 26 Figure 19 ATTENTION The pre-filter collects heavy dirt and keeps it away from the ICon Pro’s neutralization and clean compartments. When the ICon Pro’s air inlets (front and bottom) are very dirty, it is advisable to change the pre-filter sooner (for example every six months) than...
-
Page 27: Replace The Main Hepa Filter
WARNING • Always switch off and unplug the unit before replacing the main HEPA filter. • Always use the replacement filters recommended by your ICon Pro supplier. Figure 20 CAUTION Handle the filter with extreme care. Once the filter is damaged its filtration capabilities are limited. -
Page 28: Recommended Additional Cleaning
7.3 Recommended additional cleaning Keep the unit clean by wiping it with a dry cloth. Do not use any liquids to clean the ICon Pro. Occasionally clean the air inlets (front and bottom) with a vacuum cleaner and/or a dusting brush. -
Page 29: Service Interval Uv-Lamps
7.5 Service interval UV-lamps The ICon Pro is equipped with UV-A and UV-C lamps. The radiation of these lamps is crucial for proper ® functioning of the FS-ACT technology. The UV-A and UV-C lamps have a limited life span. ICon Pro software measures the operating time of each lamp in the neutralization chamber. -
Page 30: Trouble Shooting
8 Trouble shooting Your ICon Pro is designed to work maintenance free for a long time. Of course, as in every technical unit, a problem may occur. Here are some hints on how to find a solution. If this doesn't solve your problem or if your problem is not listed, contact your nearest ICon Pro service point. -
Page 31: Decommissioning And Disposal
It is the responsibility of the ICon Pro owner to dispose of the product responsibly. At the end-of-life the ICon Pro still contains valuable resources and needs to be disposed of according to your local laws and regulations regarding recycling of electrical equipment. -
Page 32: Attachments
10 Attachments 10.1 Technical specifications General specifications Power requirements 110/230V 50/60Hz Energy consumption, 4 fan speeds LOW 203W, MEDIUM 210W, HIGH 236W, MAX 250W Dimensions (without/with packaging) 1273x684x334/1328x794x444 mm Weight (without/with packaging) 72/80kg Fan motor DC 12V, long lifespan, non-stop use OK Control panel 20 character, 4-line LCD display encoder Air output (Low-Max) -
Page 33: Ce Certificate
10.2 CE certificate...