Standard AccuBind Pro Operator's Manual
Thermal tape binding system
Hide thumbs
Also See for AccuBind Pro:
- Product manual (17 pages) ,
- Installation instructions (3 pages)
Related Manuals for Standard AccuBind Pro
Summary of Contents for Standard AccuBind Pro
- Page 1 Standard Accubind Pro Tape Binding Machine Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 Operators Guide S t a n d a r d ™ A c c u B i n d P r o T h e r m a l Ta p e B i n d i n g S y s t e m...
- Page 3 Article code:108188 108168 (see rating plate) Serial number: This document contains information that is the sole property of Standard Duplicating Machines Corporation. No part of this document may be reproduced by any means whatsoever without prior written approval of Standard Duplicating Machines Corporation. Requests for additional copies will be gladly accommodated.
-
Page 4: Table Of Contents
AccuBind OPERATORS GUIDE Table of Contents Safety Instructions ............3 Safety Information ............4 Transportation and Storage ........7 Specifications ............7 Installation and Start Up..........9 Operation..............11 Malfunctions and Troubleshooting ......19 Maintenance and Servicing........20 Page 1... - Page 5 OPERATORS GUIDE AccuBind Page 2...
-
Page 6: Safety Instructions
The operating instructions can on no account replace thorough training and familiarization, but can only support these. The dealer from whom you purchased your AccuBind Pro will gladly provide you with information regarding training courses for: Operation Maintenance and servicing 1.2 Operator's Obligations... - Page 7 OPERATORS GUIDE AccuBind 1.5 Intended Use ◆ The STANDARD AccuBind is a binding device for pads, pamphlets, catalogues and calendars with a spine length of DIN A5, DIN A4, and 11". ◆ Bindings may comprise *5 - 325 sheets (*with cover). Bind thickness maximum = 1.25” (33 mm).
- Page 8 AccuBind OPERATORS GUIDE 2 Safety Instructions 2.1 Explanation of Symbols and Notes These operating instructions use the following designations and signs for danger: Warning! This symbol indicates an immediately threatening danger for the life and health of persons. Non-compliance with these instructions has serious adverse health effects, culminating in life-threatening injuries.
- Page 9 ● The permanent sound pressure level emanating from the device is 70 dB(A). 2.13 Copywright ● The copyright for these operating instructions remains with Standard Duplicating Machines Corporation. ● These operating instructions are only intended for the operator. They contain instructions and notes, which may not be duplicated either in part or in whole, disseminated or otherwise communicated.
- Page 10 Do not turn crate upside down Protect from moisture Fragile contents 4 Device Specifications Device designation: STANDARD AccuBind Pro Article code: AB-Pro 108168 (115 V) (USA) Serial number: Refer to first page 4.1 Connection Specifications Connected load: 115 V ~, 60 Hz (108168) (USA) Total output: 400 W Mains fuse 6.3 A, F 250 V 5x20mm (for 115 V) (USA)
- Page 11 Hourly output (1 person): approx. 200 bindings/hour Material to be bound Spine length11”, A4 Block thickness (5 - 325 sheets / 80gr./m²) Strip length of Standard AccuBind™ strips: 297 mm (A4) 279.4 mm (11") Strip width / pile thickness: A - 20 mm / 13/16" > 0.4 mm to 3.0 mm B - 25 mm / 1"...
-
Page 12: Safety Information
Length and quality of wires must comply with local regulations. At no time should this equipment be operated using an extension cord. Work on the equipment may only be carried out by a Standard Authorized Dealer. Please observe the regulations provided by the Employer's Liability Insurance Association in this regard. - Page 13 OPERATORS GUIDE AccuBind OPERATING PANEL 7. “Pre-Bound” binding mode indicator 1. Start button 8. “Editing” mode indicator 2. Start indicator 9. Ready to insert book block indicator 3. Stop button 10. Remove bound book indicator 4. Stop indicator 11. Tape width size indicators (A through F) 5.
- Page 14 AccuBind OPERATORS GUIDE Switching on the AccuBind The following steps on this page are required any time the machine has been switched from off to on or when the main cover has been opened and closed. Switch on your AccuBind by pressing the black switch by the power cord to the “I”...
- Page 15 OPERATORS GUIDE AccuBind OPERATING IN “NORMAL” BINDING MODE Confirm that the machine has been set for “Normal” binding mode as indicated by the lamp, if another mode lamp is lit, press the blue button until the correct lamp illuminates. At this time the “insert book”...
- Page 16 AccuBind OPERATORS GUIDE When clamp re-opens, slide book slightly to the left and immediately remove your bound book by lifting it straight up and out of the machine. Do not leave bound book in machine for more than five seconds. Note: If bound book remains in the machine for more than 10 seconds an audible alarm will be heard.
- Page 17 OPERATORS GUIDE AccuBind OPERATING IN “PRE-BOUND DOCUMENTS” BINDING MODE Confirm that the machine has been set for “Pre-Bound” binding mode as indicated by the lamp, if another mode lamp is lit, press the blue button until the correct lamp illuminates. At this time the “insert book”...
- Page 18 AccuBind OPERATORS GUIDE When clamp re-opens, slide book slightly to the left and immediately remove your bound book by lifting it straight up and out of the machine. Do not leave bound book in machine for more than five seconds. Note: If bound book remains in the machine for more than 10 seconds an audible alarm will be heard.
- Page 19 OPERATORS GUIDE AccuBind OPERATING IN “EDITING” MODE Confirm that the machine has been set for “Editing” mode as indicated by the lamp, if another mode lamp is lit, press the blue button until the correct lamp illuminates. At this time the “insert book”...
- Page 20 AccuBind OPERATORS GUIDE When clamp re-opens, slide book slightly to the left and immediately remove your bound book by lifting it straight up and out of the machine. Lay book flat on table and open to page that needs removal. Remove page and insert new one in its place.
-
Page 21: Malfunctions And Troubleshooting
OPERATORS GUIDE AccuBind 7 Malfunctions and Troubleshooting Malfunction Corrective Action LED A and F are flashing -- Book block dimension is outside = .02” to 1.25”. - Select correct block thickness. After the "Start" button has been pressed, the LED "Ready for binding" does not light up. -
Page 22: Maintenance And Servicing
AccuBind OPERATORS GUIDE 8 Maintenance and Servicing 8.1 Opening and Closing the Device Open the two wing screws. Lift the lid until the stop lever engages. When closing the device, gently push down on the lid until you have overcome the resistance in the stop lever. Close lid and tighten wing screws. - Page 23 If you do not know who the supplier is please have the serial number of your unit ready and telephone Standard Duplicating Machines Corporation at: 978-470-1920 so that we may direct you to the correct source.
- Page 25 Standard Duplicating Machines Corporation • 10 Connector Road, Andover, MA 01810 978.470.1920 Fax 978.470.2771 www.sdmc.com...
Need help?
Do you have a question about the AccuBind Pro and is the answer not in the manual?
Questions and answers