Advertisement
Quick Links
MiG-29
Scale EDF Radio Control model airplane
Wingspan : 1145mm
UNDER SAFETY PRECAUTIONS
This radio control is not a toy!
- Always keep this instruction manual ready on hand for quick reference.
- Assemble this kit only places out of children reach.
- First-time builders of EDF model should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any parts of the construction.
- Taking out liability insurance is recommended.
- You are responsible for this model's assembly and safe operation.
You need to purchase the following accessories separately to complete the assembly.
1.
Signal cable
(Throttle)
2.
Signal cable
(Elevator)
3.
Silicone Battery cable (No. 12AWG or 14AWG)
4.
Li-Po Battery, 5-cells (18.5v), 3600mAh, 20C
www.modellmarkt24.ch
www.modellmarkt24.ch
Copyright 2007 Fly Fly Hobby
C
5.
1 pc required
6.
2 pcs required
7.
2 pc required
2 pc required
60A Electric Speed Control (ESC) w/BEC
60A
2 pc required
w/ BEC
B36 Brushless Motor, 1600-1800kv,
Shaft dia 5mm
2 pc required
Micro servo, torque >1.8kg
2 pcs required
Designed and Manufactured by : Fly Fly Hobby Mfg.
Model No : FF-D004
http://www.flyflyhobby.com
Advertisement
Related Manuals for Fly Fly Hobby FF-D004
Summary of Contents for Fly Fly Hobby FF-D004
- Page 1 Silicone Battery cable (No. 12AWG or 14AWG) Micro servo, torque >1.8kg 2 pc required 2 pcs required Li-Po Battery, 5-cells (18.5v), 3600mAh, 20C 2 pc required www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
-
Page 2: Table Of Contents
Warning ! First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying a badly assembled or badly adjusted aircraft is very dangerous! In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone! This model aircraft is designed to be powered by an electric-motor. -
Page 3: Fuselage
(2) Use ‘Y’ extension cable to connect the ESC to receiver. 2. Silicone Battery cable (No. 12AWG or 14AWG) 2 pc required 30 x 12 x 3 plywood www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com... -
Page 4: Horizontal Tail Wing
Horizontal Tail 30 x 5.6 x 3mm plywood 20 x 4 x 3mm plywood Sand a flat surface Horizontal Tail www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com... -
Page 5: 25X10X3 Plywood
32 x 12 x 3mm 42 x 20 x 3mm plywood plywood Note : Assemble the front part in step-5 together. 4 mm plastic parts www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com... - Page 6 Nose gear Nose gear 38 x 9.5 x 3 plywood www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 7 Note : The cover designed for removable to access the motor & EDF. Note : Epoxy half of the cone only 4 mm plastic parts www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 8 Assembly 4 x 350 carbon rod 4 x 600 carbon rod Adjustment 140mm 160mm www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 9 Never fly before checking the CG’s required position. In order to obtain the CG requirement, reposition the receiver and battery. 147mm (5.8’’) NEVER fly the model without well balancing. www.modellmarkt24.ch www.modellmarkt24.ch Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...