Advertisement
Quick Links
F-4 Phantom-II
Scale EDF Radio Control model airplane
Wingspan : 1010mm
UNDER SAFETY PRECAUTIONS
This radio control is not a toy!
- Always keep this instruction manual ready on hand for quick reference.
- Assemble this kit only places out of children reach.
- First-time builders of EDF model should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any parts of the construction.
- Taking out liability insurance is recommended.
- You are responsible for this model's assembly and safe operation.
You need to purchase the following accessories separately to complete the model.
1.
Signal cable
(Elevator)
2.
Silicone motor cable (No. 14AWG)
3.
Li-Po Battery, 5-6 cells, 3600mAh, 20C
Copyright 2009 Fly Fly Hobby
C
2 pcs required
3 pcs required
1 pc required
Designed and Manufactured by : Fly Fly Hobby Mfg.
Model No : FF-D007
4.
60A Electric Speed Control (ESC) w/BEC
60A
w/ BEC
5.
B36 Brushless Motor, 1500-1600kv,
Outruuner or Inrunner, Shaft dia 5mm
6.
Micro servo, torque >1.8kg
1 pc required
1 pc required
3 pcs required
FLYFLY
HOBBY
http://www.flyflyhobby.com
Advertisement
Related Manuals for Fly Fly Hobby F-4 Phantom-II FF-D007
Summary of Contents for Fly Fly Hobby F-4 Phantom-II FF-D007
- Page 1 Outruuner or Inrunner, Shaft dia 5mm 3 pcs required 1 pc required Li-Po Battery, 5-6 cells, 3600mAh, 20C Micro servo, torque >1.8kg 1 pc required 3 pcs required FLYFLY HOBBY Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 2 4 x 35mm screw 2 x 7mm TP screw 3 x 10 mm screw Decal set 3 x4 mm set screw 3 x4 mm screw Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 3 Magic tape 5-6 cells Li-po Align the mark to the bottom Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 4 This is not a toy! The unit should only be operated by childs of 12 years and supervised by an adult. Signal cable (Elevator) 2 pcs required Connect to ESC Connect to receiver Silicone motor cable (No. 14AWG) 3 pcs required Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 5 Elevator 21 x 7 x 3 plywood 12 x 7 x 3 plywood Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 6 Canopy Double side tape Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
-
Page 7: Main Gear Assembly
Undercarriage Nose gear assembly Main gear assembly Wing 110 x 37 x 3 Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com... -
Page 8: Vertical Fin
Vertical fin 3mm collar 3mm set screw Elevator Make 5mm hole Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com... - Page 9 Exhaust cone Note : Epoxy the shadow portion only. 2mm Nut 1.5 x160 mm rod 3 x 4 screw Linkage Stopper 180mm Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...
- Page 10 JETTISON JETTISON CANOPIES HANDLE INSIDE CAUTION BEFORE OPERATING CONTROLS REFER TO MINIMIUM STRUCTURAL ACCESS DOOR REQUIREMENTS SECT. I MAINTENANCE MANUAL TO PREVENT DAMAGE TO AIRCRAFT Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com...