Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Smart Switch NV-2000
Summary of Contents for Smart Switch NV-2000
- Page 1 SMART SWITCH NV-2000 Navigational Light Monitor Installation Manual...
-
Page 2: Table Of Contents
Table of Contents System Overview Wiring Block Diagram Installation Steps Wiring Diagram (NV-100 ) Setting Rotary Switch (network address) Programming Instructions Operating Instructions Electrical Specifications Mounting Instructions... -
Page 3: System Overview
The NV-2000 Navigational Light Monitor has been developed to allow monitoring of up to 32 lights. It is a network system consisting of the NV-2000 Master Display Unit and up to 4 Input/Output Units located any where on the vessel. In addition, and as an option, any number of NV-200 Remote Display Units may be added to provide additional displays throughout the vessel. -
Page 4: Wiring Block Diagram
Wiring Block Diagram Black battery battery negative positive NV-2000 NR-800 Master Display Unit (MDU) Remote Display Unit (RDU) To next device Red=Battery + Red=Battery + Black=Battery - Black=Battery - Output relay Output relay NV-100 NV-100 (IOU) (IOU) Twilight Twilight Sensor input... -
Page 5: Installation Steps
Installation Steps Smartswitch Technologies Ltd recommends a Qualified Marine or Auto- Electrician installs this product. Step 1: Install and connect the Master Display Head Unit (NV-2000) page 2. Step 2: Install and connect the Input Units (NV-100) page Step 3:... -
Page 6: Wiring Diagram (Nv-100 )
Wiring Diagram for Model NV-100 Rotary switch Output 8 Battery + Comms + Comms Output 7 Comms - Battery + Output 6 Battery + Output 5 Twilight sensor adjuster Battery + Output 4 Battery + Twilight sensor Input Output 3 Sensor Twilight sensor + Battery +... -
Page 7: Setting Rotary Switch (Network Address)
Setting Rotary Switch (Network Address) To enable the MDU to remotely monitor, each I/O (NV-100) unit must have a unique network address. This is accomplished by setting the rotary switch on the side of the I/O unit to either switch position 2, 3, 4 or 5 (ref to page 6). - Page 8 NV-100 (IOU) Rotary Switch position 4 Switch Alarm Input Position 4 Input NV-100 (IOU) Rotary Switch position 5 Switch Alarm Input Position 5 Input...
-
Page 9: Programming Instructions
Programming Instructions Step 1: Placing the unit in Program Mode Press and hold down the Backlight & Scroll keys together for three seconds. This will place the unit in program mode. Step 2: Selecting Which NV-100 to program (Rotary Switch see page 7/8) The display will now show Select Switch # <... - Page 10 Programming Instructions cont. Step 7: Selecting /Creating Light Name The display will now show: PORT NAV LIGHT < Alarm Text > Use the Scroll or Backlight key to scroll through the pre-named lights. Once you have found the text required or the text you would like to change, push the Mute key. If you want to choose the name on the display push the Mute key again this will take you to step 5.
-
Page 11: Operating Instructions
If the fault condition has gone the fault text will disappear from the screen. Normal Operation Screen: SCANNING ALL LIGHTS ************************* Electrical Specifications NV-2000 Supply Voltage 12 to 32 Volts DC (Auto-sensing) Quiescent Current 0.028 Amps (backlight off) -
Page 12: Mounting Instructions
© All technologies, design and Intellectual Property is owned by Penguin Electronics Ltd Po Box 272, Waikanae, New Zealand Ph: 0064-4 293-4201 Fax: 0064-4 293-4201 Mobile: 0064-274-919-805 Email: info@smartswitch.co.nz Web: www.smartswitch.co.nz...
Need help?
Do you have a question about the NV-2000 and is the answer not in the manual?
Questions and answers