Safety Precautions:
1.
Before using the light, make sure that the electrical
outlet of your local power supplier matches the power
regulation
indicated on your lighting equipment.
2.
Do not use any power supply other than the AC
specification indicated on your equipment.
3.
Do not expose your lighting equipment to sunshine,
moisture, dust, dirt, rain, or water.
4.
Any exposure to chemical solutions, gasoline, grease,
oil, paint, or detergents can result in permanent dam-
age to your equipment.
5.
Do not insert metal parts into any lighting equipment.
Model
1
Maximum Watt Seconds
2
Guide Number
3
Flash Duration
4
Flash Variability
5
Recycling Time
6
Recycling Time - Battery
7
Recycle confirm
8
Flash Ready Indicator
9
Modeling Light Wattage
10
Color Temperature
11
Modeling Bulb Base
12
User replaceable flashtube
13
Built-In Slave
14
Slave Sensitivity
15
Synch Terminal
16
Synch Terminal Type
17
Synch Voltage
18
Voltage Stabilization
19
Fan Cooled
20
Test Button
21
Fuse
22
Reflector/Removable
23
Mount
24
Housing Type
25
Dimensions
26
Weight
Light Body & Back Control Panel
(1) Power Inlet Include Fuse
(2) Power Selection AC DC
(3) Synch Cord Socket
(4) On/Off Switch for Modeling Lamp
(5) On/Off switch for recharge read y-beeper/
Modeling lamp off
(6) Recharge Ready-Light
(7) Slave Sensor
(8) Handle Grip
(9) Locking/Releasing Bolt for Reflector& Soft
Box Connector
(10) On/Off Switch for Sensor
(11) Test Button
(12) Output Power Setting: flash/ modeling lamp
(13) Handle for Angle Adjustable
(14) Stand Mounting
MONOLIGHT 320M/620M/1220M AC/DC
FP320M
150 ws
118 ft
1/600 to 1/1000
Stepless Control from Full
Power to 1/32 Power
0.5 - 1 Second
<1.5 Seconds
Yes
Ready Light & Audio Signal
100 watts
5600° K +-
E26 - E27
yes
Yes
30ft. Radius,360 Degree
Yes
1/4" (6.35 mm) Phono Sync Terminal
5.6
110-130 ac +/- 0.5%
No
Yes
8A
8" inch
Flashpoint
Rugged Metal Housing
L 11" W 5.6" H 7.5"
3 Lbs (1.7kg)
(15) Stand Mounting Bolt
(16) Umbrella Holder
(17) Replaceable Flash Tube
(18) Modeling Lamp
(19) Cable Socket (DC inlet)
6.
Dry your hands before handling the equipment, as
touching your equipment with wet hands is dangerous
to both the equipment and to you.
7.
Do not keep the power on when the light is not in use.
8.
Do not attempt repairs to your lighting equipment
personally. If a problem arises, contact the store from
which you purchased the light.
9.
This flash has an over frequency protection circuit, rap-
id continuous firing of your flash will cause an audible
alert. continued rapid firing after audible alert will cause
the flash to cease operation and trigger a "cool down"
period of approximately of 10 seconds. after this period,
the flash will resume operation. You may also reboot
the flash by cycling the power off and then on.
FP620M
300 ws
192 ft
1/600 to 1/1000
Stepless Control from Full
Power to 1/32 Power
<1.5 Seconds
<3 Seconds
Yes
Ready Light & Audio Signal
150 watts
5600° K +-
E26 - E27
yes
Yes
30ft. Radius,360 Degree
Yes
1/4" (6.35 mm) Phono Sync Terminal
5.6
110-130 ac +/- 0.5%
Yes
Yes
10A
8" inch
Flashpoint
Rugged Metal Housing
L 15" W 5.6" H 7.5"
4-1/2 Lbs (2.4kg)
13
19
14
FP1220M
600ws
230 ft
1/600 to 1/1000
Stepless Control from Full
Power to 1/32 Power
<3 Seconds
<6 Seconds
Yes
Ready Light & Audio Signal
250 watts
5600° K+-
E26 - E27
yes
Yes
30ft. Radius,360 Degree
Yes
1/4" (6.35 mm) Phono Sync Terminal
5.6
110-130 ac +/- 0.5%
Yes
Yes
10A
8" inch
Flashpoint
Rugged Metal Housing
L 15" W 5.6" H 7.5"
7 Lbs (3.2kg)
6
7
5
4
9
READY
SOUND
SENSOR
TEST
MODEL
DIM
FULL
AC
OFF
SYNC
DC
3
18
FUSE 10A
2
1
17
16
15
8
9
10
11
12
13
14