Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SIIG AV-GM04K3-S1
Summary of Contents for SIIG AV-GM04K3-S1
- Page 1 HDMI 2.0 over IP Light Compression Multicast System P/N: AV-GM04K3-S1...
-
Page 2: Table Of Contents
HDMI 2.0 over IP Light Compression Multicast System for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the AV-GM04K3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
HDMI or DVI enabled TV sets or LCD PC monitors. Besides AV-GM04K3-S1 is HDCP compliant, and supports IR and RS-232 pass-through path. With broadcasting management software and 10 Gigabit Ethernet network switch (supported IGMP Snooping), AV-GM04K3-S1 is a complete Ultra-HD 4K2K@60(4:4:4) video broadcasting solution for digital signage. -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM04K3-S1 Technical AV-GM04K3-S1[Tx] AV-GM04K3-S1[Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance HDMI Deep Color, full 3D & 4K2K@60(4:4:4) HDCP compliance Video bandwidth Single-link 594MHz [18Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 / 4K2K@30 / 4K2K@60(4:4:4) -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting unit ► AV-GM04K3-S1-TX Front Panel +5V DC: Connect to a 5V power supply unit HDMI IN: Connect to a HDMI source with a HDMI male-male cable IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver... - Page 6 Receiving unit ► AV-GM04K3-S1-RX Front Panel +5V DC: Connect to a 5V power supply unit HDMI OUT: Connect to a HDMI display with a HDMI male-male cable IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver...
-
Page 7: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other enf to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. - Page 8 You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work.
-
Page 9: Hdmi Pin Definition
HDMI PIN DEFINITION Type A (Receptacle) HDMI Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock– Pin 3 TMDS Data2– Pin 13 Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device) Pin 5 TMDS Data1 Shield Pin 15... -
Page 10: Connection Diagram
CONNECTION DIAGRAM... -
Page 11: Operation Approach
OPERATION APPROACH Software Control through Ethernet port 1. System Requirement (1) OS information: Microsoft Windows XP/7/8/10 (2) Baud Rate: 57600 (3) Software size: 4MB (4) Minimum RAM requirement: 256MB 2. Control Interface When clicking on the executable file, the following dialog will pop up. Please click the connect button to enter the control interface. - Page 12 (2) Walls Switching User can define wall size by entering the wall parameters. Dragging Encoders or Decoders to Wall and Wall Decoders icon to setup the video wall function. Please note that the resolution of each Wall Decoders is divided by the wall size.
- Page 13 and receiver. Dragging the RS-232 icon of Senders to Receivers to make connection and sending/receiving data. (4) Infrared Routing Bi-directional IR signal can be transmitted between the transmitter and receiver. The IR signal can be generated either from receiver or a control system.
- Page 14 device Select the device which you desire to update firmware Click right button to choose update device item and firmware will start to update After updating, please reboot the device This default reset process will take about 5~10 seconds. ...
-
Page 15: Warranty
Also, the technical information contained herein regarding the AV-GM04K3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM04K3-S1 and is the answer not in the manual?
Questions and answers