Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SIIG AV-GM04H3-S1
Summary of Contents for SIIG AV-GM04H3-S1
- Page 1 HDMI over IP (fiber) Uncompressed Multicast System P/N: AV-GM04H3-S1...
-
Page 2: Table Of Contents
HDMI over IP (fiber) Uncompressed Multicast System for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the AV-GM04H3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
Ultra-HD 4K2K@30 format. Users can readily extend Ultra-HD sources from DVD players, Blu-ray Disc player, PS3, PC, and any other HDMI sources broadcasting to distant display monitors including HDMI or DVI enabled TV sets or LCD PC monitors. Besides AV-GM04H3-S1 is HDCP compliant, and supports IR and RS-232 pass-through path. -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM04H3-S1 Technical AV-GM04H3-S1[Tx] AV-GM04H3-S1[Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance HDMI Deep Color, full 3D & 4K2K@30 HDCP compliance Video bandwidth Single-link 340MHz [10.2Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 / 4K2K@30 / 4K2K@60 HDR... -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting unit ► AV-GM04H3-S1-TX Front Panel +5V DC: Connect to a 5V power supply unit HDMI IN: Connect to a HDMI source with a HDMI male-male cable Status LED: When device read the firmware, the indicator LED will light... - Page 6 Receiving unit ► AV-GM04H3-S1-RX Front Panel +5V DC: Connect to a 5V power supply unit HDMI OUT: Connect to a HDMI display with a HDMI male-male cable Status LED: When device read the firmware, the indicator LED will light Signal LED: When user connect to the display, the indicator LED will light...
-
Page 7: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other enf to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. - Page 8 You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work.
-
Page 9: Hdmi Pin Definition
HDMI PIN DEFINITION Type A (Receptacle) HDMI Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock– Pin 3 TMDS Data2– Pin 13 Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device) Pin 5 TMDS Data1 Shield Pin 15... -
Page 10: Connection Diagram
CONNECTION DIAGRAM... -
Page 11: Operation Approach
OPERATION APPROACH Software Control through Ethernet port 1. System Requirement (1) OS information : MS Win XP/7/8/10 (2) Baud Rate: 57600 (3) Software size: 17MB (4) Minimum RAM requirement: 256MB 2. Control Interface Before you execute the software, please open the software control program (based on your operating system). - Page 12 (2) Wall Switching User can define wall size by entering the wall parameters. Dragging Encoders or Decoders to Wall and Wall Decoders icon to setup the video wall function. Please note that the resolution of each Wall Decoders is divided by the wall size. For example, the resolution of wall is 1920x1080 and the wall size is 4 (2x2), the resolution of each wall decoders is 960x540.
- Page 14 (4) RS-232 Routing Bi-directional RS-232 signal are transmitted between the device transmitter and receiver. Dragging the RS-232 icon of Senders to Receivers to make connection and sending/receiving data. (5) Infrared Routing Bi-directional IR signal can be transmitted between the transmitter and receiver. The IR signal can be generated either from receiver or a control system.
- Page 15 (6) Custom Setting In the right part of the control interface, we provide the save function for user to save the video switching (mapping) into the flash memory. User also can rename the custom setting.
-
Page 16: Warranty
Also, the technical information contained herein regarding the AV-GM04H3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM04H3-S1 and is the answer not in the manual?
Questions and answers