1. Manuals
  2. Brands
  3. aci Manuals
  4. Automobile Accessories
  5. Lomax Stance Hard Cover
  6. Installation instructions manual

aci Lomax Stance Hard Cover Installation Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION INSTRUCTIONS
Thank you for purchasing a LOMAX
STANCE
Hard Cover. Agri-Cover, Inc. proudly
TM
TM
manufactured this cover using superior quality materials and workmanship. With proper
care, your cover will provide years of service and enjoyment.
NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to
installation as improvements may be made without notice. Always handle cover
and components with care. If you have questions or problems, have serial number
ready and call customer service. When done, these instructions must be given to the
consumer.
NOTICE TO CONSUMER: Before using cover, read operating, maintenance and safety
sections. Save these instructions for future reference.
FOR YOUR RECORDS
DATE PURCHASED:
WHERE PURCHASED:
SERIAL NUMBER:
(Located on decal under rear panel)
Questions? 844-566-2987
agricover.com

Advertisement

Table of Contents
loading

Related Manuals for aci Lomax Stance Hard Cover

Summary of Contents for aci Lomax Stance Hard Cover

  • Page 1 INSTALLATION INSTRUCTIONS Thank you for purchasing a LOMAX STANCE Hard Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover will provide years of service and enjoyment. NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice.

  • Page 2: Parts Diagram

    PREPARATION Ensure air and surface temperatures are above 60° F and truck box is clean. COMPONENTS TOOLS NEEDED • (8) Clamps • 1/2” Wrench • (2) Anchors • Ft-lbs torque wrench with 1/2” socket • Driver side rail • Marking tool •...

  • Page 3: Installing Side Rails

    1: INSTALLING SIDE RAILS NOTE: Some installs require special Side rail touching instructions. If required, follow special front of box instructions for side rail attachment along with these standard instructions. Safety strap hole A. Position side rail with weather strip Side rail guide provides proper side against inside lip of box, safety strap hole rail placement...
  • Page 4 1: INSTALLING SIDE RAILS (Continued) E. With side rail guide set on top of box, install second clamp on side rail 1/3 from front of box. Repeat clamping procedure. F. Install third clamp 2/3 from front of box. Repeat clamping procedure. G.

  • Page 5: Installing Cover

    2: INSTALLING COVER A. At front of box, carefully place header panel on side rails. B. Hold cover’s rear edge 1” above side rails and slide forward, then lower into retainment Latch brackets. Retainment bracket C. With cover in horizontal position, center on side rails, then slide front tabs fully under side rails and torque to 20 ft-lbs.
  • Page 6 2: INSTALLING COVER (Continued) G. Swing pivot links out from clips and attach anchors. Pivot link attached to anchor H. With anchor’s post toward cover, test placement on top of cab in flat area between ribs, then mark location. Repeat for opposite Anchor’s post side.

  • Page 7: Troubleshooting

    TROUBLESHOOTING PROBLEM SOLUTION • Top of tailgate hits cover when attempting Verify side rail guide is set on top of box. • to close Side rails are not level or set too low at rear of cover, raise rails at rear of box until cover no longer interferes with tailgate operation (see Step 1).

  • Page 8: Horizontal Position

    OPENING FOLDING COVER IMPORTANT: To avoid damage or misalignment of hinge points, open cover in a smooth, fluid manner. IMPORTANT: Remove debris or snow from hinges before opening cover. HORIZONTAL POSITION A. Open tailgate, pull release latch. B. Fold panels toward the cab, pulling additional release latch as you go.
  • Page 9 CLOSING FOLDING COVER IMPORTANT: To avoid damage or misalignment of hinge points, close cover in a smooth, fluid manner. IMPORTANT: Remove debris or snow from hinges before closing cover. A. Open tailgate. If in vertical position, release pivot link and secure in clip on each side, then lower to horizontal position.

  • Page 10: Safety Information

    SAFETY INFORMATION • Always ensure hooks and latches fully engage side rails. • Ensure safety straps are attached to side rails when cover is installed. • Ensure anchors are clear, free of interference. • Never rest cover against cab after installation. •...
  • Page 11 ALWAYS PROPERLY SECURE COVER WARNING: Failure to execute these steps may result in severe damage and will void your warranty. 1. Tabs engaged under side rails and properly torqued. 2. Safety straps attached to side rails. 3. Bungees hooked on storage brackets. HORIZONTAL POSITION ONLY: .

  • Page 12: Manufacturer's Limited Warranty

    MANUFACTURER’S LIMITED WARRANTY Agri-Cover, Inc. extends the following three (3) year Limited Warranty for the LOMAX STANCE Hard Cover: Agri-Cover, Inc. warrants a period of three (3) years from the date of manufacture that its LOMAX STANCE Hard Cover is free from defects in workmanship under normal use for the truck model it was intended for.

Table of Contents