Summary of Contents for Lenoxx Healthy Choice PM85
- Page 1 Model No: PM85 Batch No: PR3565 Please read and retain these instructions for your reference.
-
Page 2: Important Safeguards
Introduction: Bring the authentic flavours of Italy to your kitchen. The opportunities are endless with our automatic pasta makers, but one thing is certain– preparing fresh, homemade pasta has never been simpler. Our pasta makers have a huge, 600 gram capacity for flour, allowing you to create large portions to keep the whole family satisfied. Each automatic pasta maker also contains a dumpling-making tool, assisting you in preparing delicious pouches ready for your choice of succulent dumpling fillers– create your own raviolis, pierogis, and so much more. There’s nothing like a home-cooked meal. Add an authentic addition to a mealtime favourite with your fantastic, new automatic pasta maker. Important Safeguards: When operating this electrical appliance, basic safety instructions should always be followed to reduce the risk of fire, electrical shock, and/or injury. • Read all the instructions carefully, even if you feel familiar with the appliance. Save these instructions for future reference. • Before connecting the appliance to the mains, check the type of supply and the mains voltage corresponds with the appliance. This appliance is to be used in a standard domestic outlet only. • Always switch OFF and pull the plug out of the socket after using the appliance and before cleaning it. • Never pull the plug from the cord, always pull directly on the plug. • Do not carry the appliance by the cord. • Do not immerse housing body, cord, or plug in water or any other liquids. • Do not use the appliance with wet hands or standing on wet floor. • Do not let the cord hang over the edge of a table or touch hot surfaces such as the stove. • Do not operate the appliance with a damaged cord, after the appliance malfunctions, or after damage. Contact customer service immediately. • Do not allow the cord to become kinked or trapped. The cord should be laid so that there will not be any risk of anyone pulling it inadvertently or tripping over it. • If the supply cord is damaged, the cord must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard. • This appliance is intended to be used in household and similar applications such as: –... -
Page 3: Before First Use
• When using the appliance, ensure that there is sufficient air space above and around all sides for air circulation. • Make sure the appliance is properly and completely assembled before turning it on. • Do not move the appliance when it is in operation. • Do not switch on the appliance when it is upside down or laid on its side. • Do not use any accessory attachments not provided in the package to prevent injury. • Switch OFF and unplug the appliance before removing or inserting the provided attachments. Handle the attachments with care. • No claims under the warranty or liability will be accepted if result from improper or incorrect use. • Check the appliance and its components regularly for damages. Do not use the appliance if it is damaged in any way. Have it immediately repaired at an authorized service center. Do not ever attempt to repair the unit yourself. There is danger of electrical shock. • Keep your hair, clothing, and jewelry away from the rotating parts. • Do not leave the appliance unattended while it is in use. • Do not touch the moving parts of the appliance. • Do not operate the appliance continuously for longer than 20 minutes. Allow the appliance to cool completely before using it again. • This product is not intended to be operated by means of an external timer or separate remote control system. • When storing the appliance wrap the cord neatly to avoid unnecessary strain on the cord. Before first use: • Thoroughly clean all parts that contact food using hot soapy water. • Place the appliance on an appropriate work surface. • Please be familiar with the appliance and instructions before connecting it to a power outlet. -
Page 4: Parts Included
Parts included: Liquid drop cup Unit base Mixing container Turbine Screw Evacuation tube Pasta disc Disc screw... - Page 5 Assembly: Place the unit on a horizontal and stable working surface. Insert mixing container horizontally onto the unit base by thoroughly pushing it through to the back of the base, with the large round opening facing out and the square opening on top. Insert the screw (spiral rod) into the evacuation tube. The rod on the screw will stick out of the hole at the end of the evacuation tube. Insert the turbine onto the driving rod of the screw. The hole in the turbine shaft connects with the rod of the screw. Insert the turbine into the mixing container through the large round opening. The metal end on the turbine connects into the hole at the rear of mixing container and the main body of the pasta maker. The screw and evacuation tube will need to remain attached to the turbine when you do this. Attach the evacuation tube to the mixing container. Lock it into place by rotating the evacuation tube clockwise. Choose the pasta disc that you would like to use and add it onto the end of the evacuation tube. Lock the pasta disc onto the tube feed using the disc screw. Screw the disc screw clockwise. Place the lid on top of the mixing container into which all of the parts have been installed, then lock the lid on the container. Note: The pasta maker will not work without the lid correctly in place. When you need to disassemble the appliance, please remove the lid first. When the unit and parts have been assembled correctly and the lid has been added and closed into the correct position (and the power cord is connected to the unit), the unit will beep and the machine will be ‘on’. There will be red dashes on the display panel of the unit. The liquid drop cup: The liquid drop cup sits on top of the lid of the pasta maker. The small holes in the liquid drop cup allow water to gradually trickle down into the inner body (mixing container) and then be mixed gradually into the flour. Adding the water to the flour mix gradually using this method results in a good consistency of dough mixture.
-
Page 6: Control Panel
measuring cup, as the volume of the ingredients needed may differ. The liquid measuring cup is an additional cup you could use to add multiple water cups to the liquid drop cup. The included dumpling press can be used with dough to make your own home made dumplings. Extrude from the unit with the lasagna/dumpling disc. Cut the extruded dough into smaller sections. Lay the sections of dough across the dumpling press. Add your chosen filling into the center of the dumpling press. Then fold the dumpling press in half to seal the dumpling. Open the dumpling press to remove the dumpling. Cook your made dumplings in boiling water. The pin hole scraper is a tool which can assist in cleaning the pasta discs. Poke the pointy end of the pin hole scraper into the holes or groves in the discs to remove the left over pieces of dough. Control panel: Mix button: When pressed, the time on the panel will be displayed as 04:00. The time will blink on the screen for 4 seconds. Then the unit will enter mixing mode and count down from 4 minutes of time while mixing your added ingredients. At the end of the 4 minutes mixing time, the unit will stop mixing and beep to alert you that the mixing time has ended. The mixing time can also be adjusted. After pressing the mix button (before the mixing process begins), use the – or + buttons to adjust the mixing time. When your chosen time is shown on the display screen, do not press anything. The time will blink on the screen for 4 seconds and then the unit will enter mixing mode and count down from your chosen time. The mixing time is adjustable in 10 second intervals. - Page 7 making 2 cups of flour noodles). When your chosen mode is shown on the screen, no not press anything and in 4 seconds the unit will begin operation in that mode. At the end of the automatic cycle, the unit will stop operation and beep to alert you that the time has ended. Extrude button: When pressed, the time on the panel will be displayed as 12:00. The time will blink on the screen for 4 seconds. Then the unit will enter extrude mode and count down from 12 minutes of time while extruding pasta. At the end of the 12 minutes extruding time, the unit will stop extruding and beep to alert you that the extruding time has ended.
- Page 8 *** Manually make 2 cups of flour noodles Preparation: Assemble the pasta maker with your chosen pasta disc. Take 2 flat cups of flour with the dry ingredient measuring cup, take 2 cups of water with small water cup. Stir Manually: A) Pour 2 flat cups of flour into the mixing container. B) Close the lid (Ensure it is closed and locked into place). C) Assemble the liquid drop cup onto the corresponding position on the lid. D) Connect the power lead (The screen display will show “----”, which means the machine is on idling status); E) Press the mix button. The display will blink for a few seconds and then begin operation. F) Once upon the machine starts to stir the flour, immediately pour 1 small cup of water into the water drop cup. G) Wait until the completion of stirring. Compress Noodle Manually: Upon completion of the above manually stirring (flour) Press the extrude button. Set timing for noodle extrusion. Use the + and – buttons to increase or decrease the extrusion time. (Normally noodle compression for 2 cups of flour can be completed in 12 minutes). When your chosen time is shown on the screen, do not press anything. The time will blink on the screen and then the pasta maker will begin extrusion. Wait until the completion of noodle extrusion. *** Automatically make 1 cup of flour noodles Preparation: Same as manually make 1 cup of flour noodles.
- Page 9 Notes: This machine has a short time memory function: During the process of stirring or noodle extrusion, if instant power off occurs or the lid has been opened and closed again in a short time, the machine can resume the original work process. If you want to stop the short time memory, you may press the Cancel key once with power connected.
-
Page 10: Troubleshooting
Troubleshooting: PROBLEM SOLUTION The machine does not turn on. Ensure that the power lead is connected correctly. Ensure that the lid is closed tightly. Ensure that the lid is latched securely to mixing container correctly. Ensure that the mixing container has been fitted firmly to the back wall of the unit base correctly, Hold the mixing container up against the back wall of the unit base. There is an interlocking safety switch which may have been triggered if the container or lid was not fitted properly. Delayed starting. The motor has a slight inbuilt delay system to get the unit functioning prior to parts moving. This is completely normal. Appliance stops while mixing or Ensure that the mixing container has been fitted firmly to the back wall of extruding the unit base correctly. Hold the mixing container up against the back wall of the unit base. EEEE – Error message is shown There is an interlocking safety switch which may have been triggered if the on the screen. container or lid was not fitted properly. If the unit stops while mixing, you can also turn the unit off, open the lid and remove any pasta dough stuck under it. Refit and close the lid properly and switch the unit back on. Ensure that the lid is latched securely to the mixing container correctly. The lid and inner body plastic Reduce the amount of ingredients in the mixing container. -
Page 11: Cleaning And Storage
There is too much dough left in Complete another extrude cycle with more time to extrude more pasta. the mixing container. Use a smaller quantity of flour and water. Appliance is noisy. The general operation of this unit will create noise, however loud clunks or thumping are not normal. Turn the unit off and check that the appliance is assembled correctly. There is steam coming out of the There may be some hot steam escaping from the tube feed. This is unit near the evacuation tube or completely normal. pasta disc. Do not touch the evacuation tube, screw or pasta disc when hot and immediately after extrusion. The metal point on the screw may also be hot after extrusion. Take care not to handle it when hot. A small amount of flour or water This is normal as mixing container and evacuation tube are not sealed. has come out from the bottom of the mixing container. Cannot remove the disc screw. Put the unit in mix mode for a few seconds. This will relieve pressure on the disc screw and pasta disc. Cleaning problems - You will find the parts easier to clean if you leave the parts to dry in the air for one hour. Disposal: At the end of the product’s life-cycle, it should go directly to a specially adapted waste-recycling centre. •...