SEA Praha GSM-R5-ZAS Series Manual

GSM-R5-ZAS, GSM-R5-ZAS-xxx

1. Introduction

GSM relay
The GSM-R5-ZAS (hereinafter referred to as
by SMS messages over GSM network. Other features include, for example, remote
temperature control, „ring-out" control of the appliance, or an additional input for event
and alarm reporting. The device remembers its status and parameters, so it doesn't
GSM relay
have to be setup after every power-on.
terminal block located on the side of the device designed to connect one analog input
for temperature or logic value measurement. GSM relay
connection, installation and control. It is connected to the existing power supply of the
appliance. This supply can then be switched on, off, temporarily disconnected or used
to automatically control the heating to the desired temperature. The state of the
connected inputs can be detected by SMS messages or the
to send SMS messages whenever state of the input is changed. In addition to the basic
version with the terminal block on the side there are also variants with additional
features.
1) Plug for insertion into the mains 230 V
AC.
2) Socket 230 V for connecting the
AC.
controlled device (10 A, 2300 W)
3) ON/OFF (yellow LED + button)
4) PWR (green LED for indication of power)
5) Micro USB for configuration
6) SIM card holder
7) Removable terminal for connecting
external temperature sensor (the sensor
must be ordered separately).
8) GSM (blue LED for indication of
connection to GSM network)
For the basic variation it is possible to
order the connector for the external
antenna GSM-R5-ANT.
9) For other variants, there is 6pin terminal
form the underside. See chapter
„Variations with EXTENSIONS".

2. Commercial packaging

1ks GSM relay 5
1ks 2 pin connector, pitch 3,81mm
1ks 6 pin connector, pitch 3,81mm ...only variants with extensions.
1ks Articulated antenna 2dB...............only variants with additional features.
1ks screwdriver 2mm

3. Recommended accessories

GSM-C-T2 semiconductor temperature sensor in plastic
enclosure, 1m cable.

4. First time startup

1. For proper device operation a SIM card is required. The SIM card have to be
functional, activated and with disabled PIN code. Prepaid credit cards must have
nonzero credit.
Before inserting the SIM card into the GSM relay
first disable the "PIN code" !
Insert activated SIM card into any working phone and disable PIN code. In
most mobile phone devices this option is under Settings -> Security.
2. Insert the card into the Holder Push the card inside, until you hear mechanical
.
„click".
3. Now you can insert the device into the mains. If the socket is OK green LED PWR
will turn on.
4. Now connect your electrical appliance into the GSM relay
5. First press the button on the GSM relay 5 . The relay will change its state and yellow
LED ON/OFF should light up.
6. Send SMS message „1234 OFF" to the SIM card you've inserted into the GSM
relay 5 . This will turn off the socket and add your telephone number into its list
under name MASTER. The password 1234 can be later changed. The device will
execute ... to anyone with correct password.
7. ???
8. Test the temperature control, for example at 25° C. The socket will switch on and
off according to the temperature input A1. Connect the temperature sensor to the
temperature input A1 and send the SMS 1234 TEMP 25. The control is terminated
by a 1234 OFF message or by pressing the ON / OFF button.
9. Factory setting of GSM relay5 can be restored by sending a 1234 !FACTORY
message. If you made a backup configuration of SeaConfigurator settings (Settings
tab -> Files button -> File option), you can restore your settings from this backup
(Settings tab -> Files button -> File option).
10. The names of the inputs, outputs (their states) and the command names can be
modified according to your ideas using the SeaConfigurator configuration
software. This configuration program can be downloaded free of charge from
www.seapraha.cz (enter the word „Configurator" in the search) and install it on
your PC.
gsm-r5-zas_user_manual en v2-06

5. Technical specification

Parameter
Dimensions
5
) is relay controlled remotely
Power Supply
Battery
5 is equipped with a removable
Digital outputs
5 is tailored for easy
Analog input
GSM relay 5 can be set up
Temperature
Humidity
GSM relay
1
For basic variant, it is possible to order Li-ION accumulator for reporting of power
failure..... GSM-R5-BAT.
2
For more specification see chapter „Versions with extensions".
3
4

6. Hardware

5
6

6.1 Connectors

GSM relay5
7
of external appliance. the on / off switching is done by built-in relay.
It is possible to connect one external temperature sensor KTY81-210. The length of the
wires to the connected external temperature sensor is not limited, but it should be
8
considered that the longer conductor has a certain resistance that affects the measured
value. 16 Ω equals approximately 1 ° C.

6.2 LED diodes

LED
GSM
PWR
ON/OFF
socket (Y2)

6.3 SIM card holder, button, USB and antenna

Insert SIM Card according to the picture. Push the card inside, until you hear mechanical
„click".
Press the ON / OFF button briefly to switch on or off the appliance connected in the
socket. If the GSM relay
5 device, you must
switches off by pressing for a long time (>= 5 seconds).
Micro USB connector is for offline configuration with SeaConfigurator.
If the device is equipped with an antenna connector, the antenna is connected via the
SMA connector. The device is fitted with a SMA female connector, the connected
antenna must have a male SMA connector. The impedance is 50 Ω. If there is no
connector, the device is fitted with an internal antenna.

6.4 Battery

5 . GSM relay
the device is able to operate in normal mode for about a day (the duration depends on
how much it is used).

7. Configuration

GSM relay
cable no. HW-11.02) or through the GPRS connection. This configuration program can
be downloaded for free from
install it on your PC.
GSM relay
requirements, so it is possible to use the device even without SeaConfigurator. Simply
send the first SMS from the main user's phone number under the "First time startup"
chapter.
Some parameters be changed via SMS, see chapter „Command List".
Symbol MIN. TYP.
Width W 65
Length L 140
Depth D 95
Voltage PWR 100 230
Consumption 1
Li-ION Operation after power failure
Mains socket - Y2 (switched relay)
Voltage V According to the supply voltage
OUT
Max. current -
I
OUT
Resistive load
External (removable) temperature sensor GSM-C-T2
distinction 0,1°C. accuracy in range 0 to 30 °C ... 1 °C
Temperature
A1 -30
measurement
Storage tSTG -40
Operational Ta -20
RVmax
5 is intended for indoor use
!
has a plug, that plugs into the mains and a switched socket for connection
Color Meaning
Indicates device status. Possible states are:
Blue Flashing 1:1 ... the device is setting up
Short flash 1x in 4 sec ... device is in operation.
It is permanently lit when powered from an external
Green source.
Flashes while running on the internal battery.
Yellow Shines continuously when the socket is switched ON
5 is not powered and the battery is installed, the GSM relay
5 It can be equipped with a 3.7 V stand-by Li-Ion battery. After power failure,
5 is configured with SeaConfigurator either via the USB connector (microUSB
http://www.seapraha.cz (search for „Configurator") and
5 is shipped with a factory configuration that meets the most common
MAX. Unit
mm
mm
mm
250 V .
AC
3 W
20 hours
10 A
+55 °C
+85 °C
+40 °C
90 %
5
strana 1 / 5