TEMPERED HIPSWITCH 100 Series Platform Manual

Industrial Security Appliances
TOP & FRONT PANEL LAYOUTS

MULTI-PURPOSE BUTTON

NOTE: Some Tempered Networks documents may refer to this as a "Reset" button.
The multi-purpose button provides two different functions, depending on how long it is pressed and
held.
Short Tap Press for 3 seconds and release. The Status LED will now
blink steadily.
Long Tap Press for at least 8 seconds and release. The Status LED
will now blink in a 2 flash, 1 flash pattern,
NOTE: To exit diagnostic mode, press the reboot button in the diagnostic interface or cycle the input
power of the HIPswitch.
DIMENSIONS

PACKAGE CONTENTS

Qty Item
x1 HIPswitch-100
x1 DIN-rail kit (attached)
HIPswitch™-100 Series
1. Power input connector
2. SIM slot (100g only)
3. LED: Power input #1 indicator
ON = Activated
4. LED: Power input #2 indicator
ON = Activated
5. LED: PoE indicator
ON = Power supplied over Ethernet
on port 1
6. LED: Link and activity for port 1
ON = Port is linked
Blinking = Data is being transmitted
7. LED: Link and activity for port 2
ON = Port is linked
Blinking = Data is being transmitted
8. LED: Blink = Cellular modem ready
9. LED: Status (see Status Codes)
10. Multi-purpose button
(see Multi-purpose button table)
11. Ethernet port 2
12. Ethernet port 1
(optional PoE)
13. Aux. cellular antenna connector
(100g only)
14. LED: Serial receive activity (-s models only)
15. LED: Serial transmit activity (-s models only)

16. Serial connector (-s models only)

17. Main cellular antenna connector (100g only)
Places the HIPswitch
in diagnostic mode.
Resets the HIPswitch
to factory defaults.
Qty Item
x2 Wall-mount kit
x2 4-pin terminal block
EN
DOC-0053-A
PLATFORM GUIDE
The HIPswitch™-100 Series is a small form
factor industrial grade security appliance
that facilitates private overlay networks
between customer-provided equipment and
devices. This document contains import-
ant operating information, specifications,
and installation instructions for the HIP-
switch™-100.
MODELS
Part Number Model
101e-201 HIPswitch-100e
101g-201 HIPswitch-100g
101e-s-201 HIPswitch-100e-s
101g-s-201 HIPswitch-100g-s

Safety and Warnings

Elevated Operating Ambient: If instslled in a closed environment, make sure the
operating ambient temperature is compatible with the maximum ambient temperature
specified by the manufacturer.
Reduced Air Flow: Make sure the mount of air flow required for safe operation of the equipment
is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition
due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on over-current protection
and supply wiring. Appropraite considertation of equipment nameplate ratings should be used
Explosion Hazard: Do not disconnect equipment unless power has been removed or the area is
known to be non-hazardous.

WIRING

Power Inputs

This device supports dual redundant power supplies, power supply 1
(PWR 1) and power supply 2 (PWR 2). The connectors for PWR 1 and
PWR 2 are located on the terminal block.
Step 1: Insert the negative DC into the V- terminal and the positive DC
into the V+ terminal.
Step 2: To keep the DC wires from pulling loose, use a small flat-blade
screwdriver to tighten the wire-damp screws in the front of the terminal
block connector.

Power over Ethernet Warning

Use only with IEEE 802.3af compliant power sources. Power over Ethernet is optional on port 1.
DO NOT attempt to apply Power over Ethernet on port 2
Serial Connector
(-s models only)
Pin # RS-232 RS-422
1 DCD Tx-
2 RxD Tx+
3 TxD Rx+
4 DTR Rx-
5 GND GND
6 DSR N/C
7 RTS N/C
8 CTS N/C
9 RI N/C

Status LED Codes

Normal Operation On Steady
O O = =
Conductor Blink
O O O = = O = =
Missing Identity
O O = = O = =
Factory Reset
O = O = (fast blink)
Diagnostic Mode
Revision Date: April 7, 2017
HIPSWITCH™-100 SERIES
e-mail: support@temperednetworks.com
Phone: +1 206.452.5500 ext. 2
www.temperednetworks.com
3101 Western Ave.
Ste. 550
Seattle, WA 98121
Hardened. Resilient. Simple.
HIPswitch™-100 Series
10/100 4g Serial
Ethernet Cellular
2 No No
2 Yes No
2 No Yes
2 Yes Yes
RS-485 RS-485
(4-wire) (2-wire)
Tx- DATA-
Tx+ DATA+
Rx+ N/C
Rx- N/C
GND GND
N/C N/C
N/C N/C
N/C N/C
N/C N/C
O Blink
No Conductor Connection O O O O = = O O = =
O O O O = = O O O = =
System Error
O O O O = = =
Secure Network Error
O O O O = = O = =
No Shared Network
O O O = = O O = =
Downloading Firmware
O O O = = =
Updating Firmware
PLATFORM GUIDE
802.3af PoE
Yes
Yes
Yes
Yes
= Pause