Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axis A4010–E
Summary of Contents for Axis A4010–E
- Page 1 AXIS A4010–E Reader Installation Guide...
- Page 2 This equipment has been designed and tested to fulfill Every care has been taken in the preparation of this applicable standards for: document. Please inform your local Axis office of any inaccuracies or omissions. Axis Communications • Radio frequency emission when installed...
- Page 3 Safety Directive 1999/5/EC. This product complies with IEC/EN 62368-1 and IEC/EN 60950-22, Safety of Information Technology Par la présente Axis Communications AB déclare que Equipment. l’appareil ce produit est conforme aux exigences Disposal and recycling essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
- Page 4 Support Should you require any technical assistance, please contact your Axis reseller. If your questions cannot be answered immediately, your reseller will forward your queries through the appropriate channels to ensure a rapid response. If you are connected to the Internet, you can: •...
-
Page 5: Hazard Levels
AXIS A4010–E Reader Safety information Hazard levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. - Page 6 NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to shocks or heavy pressure.
- Page 7 AXIS A4010–E Reader Transportation NO TICE TICE TICE • When transporting the Axis product, use the original packaging or equivalent to prevent damage to the product.
- Page 8 In cases where pieces of information contradict each other, the requirements for UL compliance always replace general information and instructions. For use with the UL294 listed, Axis Communications model A1001 Network Door Controller. Safety instructions •...
- Page 9 WW= manufacturing week • zzzzzz = sequence number Firmware version AXIS A4010-E Reader has been tested for compatibility with the UL294-listed Axis model A1001 Network Door Controller employing firmware version 1.50. Performance Levels for Access Control This section contains performance level information required for UL 294 compliance.
-
Page 11: Installation Steps
AXIS A4010–E Reader Installation Guide This Installation Guide provides instructions for connecting AXIS A4010-E Reader to a network door controller. AXIS A4010-E Reader is an OSDP reader that is designed to communicate with Axis network door controllers. Installation Steps Make sure the package contents, tools and other materials necessary for the installation are in order. - Page 12 AXIS A4010–E Reader Frontplate Core unit Cable Red LED Green LED Double sided tape Reader Feedback The table shows the feedback signals that are preconfigured in the reader when connected to an Axis network door controller.
-
Page 13: Specifications
AXIS A4010–E Reader LED indicator Beeper pattern Event/state Door locked Silent Steady red Door unlocked Silent Steady green Access granted One short beep Steady green Access denied One long beep Steady red Pre-alarm warning Short beeps until Steady red entering new state... - Page 14 EN 50581 (RoHS) IEC/EN 60529 IP54 UL294, 6th Edition PVC free Dimensions 85 x 46 x 19 mm (3.35 x 1.8 x 0.75 in) (HxWxD) Weight 128 g (0.28 lb) Warranty Axis 3-year warranty and AXIS Extended Warranty option, see www.axis.com/warranty...
- Page 15 Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with a rated output current limited to ≤2 A. For example, AXIS A1001 Network Door Controller fulfills these requirements when powered by Power over Ethernet (PoE) or a SELV-compliant LPS.
- Page 16 • The recommended maximum cable length is up to 30 m (98.4 ft). Connection with AXIS A1001 To use the reader with AXIS A1001, connect the RS485 wires from A to B and from B to A. For more information about Axis network door controller connections, see the hardware pin chart, generated through the door controller’s hardware...
- Page 17 In the door controller, the alarm event can be used to trigger an action. For information, see the door controller’s User Manual. Note Mount the Axis product first and then connect the cable. The accelerometer (for tampering alarm) is calibrated at power on. RS485 Termination...
-
Page 18: Install The Hardware
AXIS A4010–E Reader Install the hardware Remove the frontplate from the core unit. - Page 19 AXIS A4010–E Reader Make a hole in the bottom of the core unit and let the cable run through it.
- Page 20 AXIS A4010–E Reader Make a hole in the frontplate. Run the cable through it.
- Page 21 AXIS A4010–E Reader Hold the core unit against the wall at maximum 2 m (6.56 ft) above the ground. Mark your holes with a pencil. Drill holes in the wall and mount the core unit to the wall. Use drill bits, screws and plugs that are appropriate for the...
-
Page 22: Further Information
Fasten the double sided tape onto the main unit. Position it carefully under the two LEDs. Push the frontplate onto the main unit. Further information • For the latest version of this document, see www.axis.com • For useful online trainings and webinars, see www.axis.com/academy Warranty information For information about Axis’... - Page 24 Installation Guide Ver. M6.2 AXIS A4010–E Reader Date: April 2017 © Axis Communications AB, 2016 - 2017 Part No. 1691048...