Subscribe to Our Youtube Channel
Related Manuals for Wilson Electronics Weboost AM100-PRO
Summary of Contents for Wilson Electronics Weboost AM100-PRO
- Page 1 . :: weboost. A WILSON ELECTRONICS BRAND AM100-PRO Vehicle Signal Booster Kit User Manual boltontechnical.co.za 011 749 3085 NEED HELP?
- Page 2 ______ Index Package Contents Mount Outside Magnetic Antenna STEP 1: Mount Inside Antenna STEP 2: Connect Coax Cables To Booster STEP 3: Connect Power Supply To Booster STEP 4: Plug Power Adapter Into Vehicle’s Power Supply STEP 5: Light Patterns Troubleshooting Safety Guidelines Specifications...
- Page 3 ________ Package Contents Outside Inside Power AM100-Pro Antenna Antenna Supply Booster AM100-PRO VEHICLE SIGNAL BOOSTER...
- Page 4 Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 30 centimeters away from any other antennas • At least 30 centimeters away from any windows (including sunroofs) Clean the surface where you will place the outside antenna.
- Page 5 (STEP 1 cont.) Different vehicles cable can be routed. See examples below. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. NOTE: When going through car wash, remember to remove your antenna.
- Page 6 Step 2: Mount Inside Antenna Identify a place to mount the 4G In-Vehicle Antenna, either on the side of the seat or on the dash and mount. The location should be at least 45 centimeters but no more than 90 centimeters from where the cellular device will be used.
- Page 7 Step 3: Connect Coax Cables To Booster Connect the cable from the Mini-Mag Mount Antenna to the port labeled "Outside Antenna" on the Drive AM100-Pro booster. NOTE: Bracket can be used to fasten booster in a specific location if desired. Connect the cable from the 4G In-Vehicle Antenna to the port labeled "Inside Antenna"...
- Page 8 Step 4: Connect Power Supply To Booster Connect the power supply cord to the end of the AM100-Pro labeled "Power." NOTE: Do NOT connect the power to the Signal Booster until you have connected both the Inside and Outside Antennas. ■...
- Page 9 Step 5: Plug Power Adapter Into Vehicle's Power Supply Plug the power adapter into vehicle's 12V DC power supply. Power up your AM100-Pro by flipping the switch on the back of the DC power adapter on. If your Drive AM100-Pro is working correctly, the light will be green.
-
Page 10: Light Patterns
______ Light Patterns Solid Green This indicates that your booster is functioning properly and there are no issues with installation. Blinking Red, Then Solid Green This indicates that one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. This is a built in safety feature to prevent harmful interference with a nearby cell tower. -
Page 11: Troubleshooting
______ Troubleshooting FIXING BLINKING OR SOLID RED ISSUES This section is only applicable if the booster is red or blinking red and you are not experiencing the desired signal boost. Unplug the Booster’s power supply. Relocate the inside and outside antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. -
Page 12: Safety Guidelines
______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Any antenna used with this device must be located at least 20 centimeters from all persons. This is a CONSUMER device. The AM100-Pro is an ICASA Approved and Registered Device. -
Page 13: Specifications
Specifications AM100-Pro Specifications Product weBoost Signal Booster Model Number AM100-pro Connectors Antenna Impedance OHm Frequency MHz 1920-1980 / 2110-2170 1710-1785 / 1805-1880 880-915 / 925-960 Bands Passband Gain UL/DL 53.9 / 53.7 49.8 / 51.8 49.3 / 50.1 20 dB Bandwidth (MHz) Typical 74.8 85.6... -
Page 14: Year Warranty
1 YEAR WARRANTY weBoost Signal Boosters are warranted for one (1) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. - Page 15 Represented by Bolton Technical: Sole Distributors in Soutth Africa 011 749 3085 boltontechnical.co.za Copyright © 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents Approved for use in South Africa by ICASA.
Need help?
Do you have a question about the Weboost AM100-PRO and is the answer not in the manual?
Questions and answers