Advertisement
3. SpeCifiCATion
model no: ................................................................. SA1008
Air Consumption:.......................................................... 14cfm
Air Inlet Size: .............................................................1/4"BSP
Chuck Size: ................................................................. Ø6mm
Free Speed: ............................................................. 4500rpm
noise Power/Pressure: ...................................... 101dB/90dB
operating Pressure: ...................................................... 80psi
Vibration/Uncertainty: ................................... 0.461/0.541m/s²
4. prepAring for uSe
4.1.
Air Supply (reCommenDeD hooK-up proCeDure iS ShoWn in fig.2)
4.1.1.
Ensure tool air valve (or trigger) is in "off" position before connecting to the air supply.
4.1.2.
You will require an air pressure of 70-90psi, and an air flow according to specification.
WArning! Ensure the air supply is clean and does not exceed 90 psi while operating the tool. Too high an air pressure and
‰
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3.
drain the air tank daily. Water in the air line will damage the tool.
4.1.4.
Clean air inlet filter weekly.
4.1.5.
line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all
connections are secure.
4.2.
CouplingS
Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome
this, connect a leader hose to the tool. A quick change coupling may then be used to connect the leader
hose to the air line recoil hose (see figs 1 & 2).
fig.2
5. operATion
WArning! ensure you read, understand and apply safety instructions before use.
‰
The work space shall be well ventilated.
9
Use only the recommended lubrication oil, such as Sealey ATO/500 or ATO/1000.
9
The chuck key is used to loosen or tighten the chuck jaws so that change of drill bit is possible. Make sure that the chuck key is
9
removed and the drill bit is securely clamped before drilling starts.
5.1.
fiTTing Drill BiT.
5.1.1.
Regularly check the drill bit and always change if worn, cracked or otherwise damaged.
WArning! disconnect drill from the air supply before placing drill bit into chuck.
‰
5.1.2.
Open or close the chuck jaws to a point where the opening is slightly larger than the drill or tool bit (fig.3.A) to be used. Also raise
the front of the drill slightly to prevent drill bit from falling out of the chuck jaws. Insert the drill bit into the chuck as far as it will go.
Place the chuck key in one of the chuck holes and tighten the chuck securely.
WArning! ensure the chuck key is removed before starting the drill.
‰
5.2.
on-off DeviCeS
5.2.1.
The on-off device is of trigger type that is on the contour of the grip. This tool stops rotation within few seconds, after releasing the
trigger. For safety, place it on a level plate or on hanger after it completely stops.
noTe:
Squeeze the trigger to check that the drill is working correctly before starting work.
Do noT allow drill to run freely for an extended period of time as this will reduce bearing life.
8
WArning! Ensure you wear approved safety goggles and any other safety item required for the job. Remove the chuck key before
‰
using the drill. ensure that all other safety requirements are followed.
5.2.2.
Hold tool firmly and place the drill bit tip to the point to be drilled.
5.2.3.
depress the trigger to start drill. Move the drill bit into the work piece applying only enough pressure to keep the bit cutting.
Do noT force or apply side pressure to elongate the hole.
8
5.2.4.
If the material to be drilled is free standing it should be secured in a vice or with clamps to keep it from turning as the drill bit
rotates.
5.2.5.
When drilling metals, use a light oil on the drill bit to keep it from overheating. oil will prolong drill bit life and improve the drilling
action.
5.2.6.
For hard smooth surfaces use a centre punch to mark desired hole location. This will prevent the drill bit from slipping as drilling
commences. A pilot hole may be necessary to assist the final drill size through the work piece. Lock a pilot drill (smaller size drill
than the finished hole size) into the chuck. Drill a pilot hole in the middle of the centre punch mark where final hole is to be drilled.
Insert the final sized drill bit in chuck. Hold drill firmly and place the bit at the entrance of the pilot hole and depress the trigger.
© Jack Sealey limited
Original Language Version
fig.1
fig.3
SA1008 Issue 2 (3) 19/12/19
Advertisement
