Table of Contents
Advertisement
Quick Links
Users' manual and
parts book
Speed-Clean
Serial number:
Translation of the original operating
instructions
ATTENTION:
FOR SAFE USE OF THE MACHINE AND FOR THE BEST RESULTS IT IS VERY
IMPORTANT THAT THIS USER'S MANUAL IS READ METICULOUSLY BEFORE USE OF
THE SPEED-CLEAN.
1917 English 947.120.214
Kwekerijweg 8
3709JA Zeist
The Netherlands
T: (31)306933227
F: (31)306933228
E:
verti-drain@redexim.com
www.redexim.com
Advertisement
Table of Contents
Related Manuals for Redexim Speed-Clean
Summary of Contents for Redexim Speed-Clean
- Page 1 Serial number: Translation of the original operating instructions ATTENTION: FOR SAFE USE OF THE MACHINE AND FOR THE BEST RESULTS IT IS VERY IMPORTANT THAT THIS USER’S MANUAL IS READ METICULOUSLY BEFORE USE OF THE SPEED-CLEAN. 1917 English 947.120.214...
-
Page 2: Foreword
FOREWORD Congratulations on your Speed-Clean purchase. For safe and long-lasting operation of this Speed-Clean it is necessary to read and understand this user’s manual. Without full knowledge of the contents it is impossible to work with this machine safely. The following page deals with the general safety instructions first. Every user must know these and use them. -
Page 3: Safety Instructions
Making alterations or additions to the Speed-Clean (excluding those approved by the manufacturer) are not permitted, in principle, for safety reasons. If modifications to the Speed-Clean have been made, then the current CE mark is cancelled and whoever made these modifications must apply for a new CE mark... - Page 4 When using the public highway the applicable traffic regulations also apply. Transporting people is not permitted! Do not use the Speed-Clean in the darkness, during heavy rainfall/ storms or on slopes with an angle over 20 degrees.
- Page 5 These safety stickers must be properly visible and legible at all times, and be replaced when damaged. During operation NO persons without the proper personal protective equipment are permitted in the danger area of the Speed-Clean, because there is danger of physical injury there from spurting materials (Fig. 3) Fig.
-
Page 6: Eu Declaration
EU DECLARATION We – Redexim BV, Utrechtseweg 127, 3702 AC Zeist, Holland – declare entirely under our own responsibility that the product SPEED-CLEAN WITH A MACHINE NUMBER AS INDICATED ON THE MACHINE AND INDICATED IN THIS MANUAL to which this declaration refers, complies with stipulation of the 2006/42/EC machine directive... -
Page 7: Table Of Contents
WORKING DEPTH ADJUSTMENT OF BRUSH ..............11 ADJUSTABEL RAKE / REAR BRUSH ................12 TRANSPORT OF THE SPEED-CLEAN ................13 THE DRIVING SPEED ....................13 THE USE OF THE SPEED-CLEAN .................13 START/STOP PROCEDURE ..................13 10.0 EMPTYING OF THE DIRT RECEIVING BIN ..............14 11.0 PROBLEM ANALYSIS ....................15 12.0 MAINTENANCE ......................16... -
Page 8: Technical Data
- Ground-hugging dragging brush. - Easily changeable sieve. - Manual cylinder with manual and tool set. - Rake section Options - Sieve elements with various drainage dimensions. GENERAL DESCRIPTION The Speed-Clean is a surface cleaning machine for cleaning artificial turf. -
Page 9: First Installation
FIRST INSTALLATION Fig. 6 The machine is delivered on a pallet in transport position. To take the machine off the pallet and place it horizontally, act as follows: (Fig. 6) !! NEVER CRAWL UNDER THE MACHINE !! Attach a cable to the lifting points on both sides of the machine, and to the top of the 3- point hitch on the front. -
Page 10: Coupling / Disconnecting
Without them the machine must NEVER be used. Fig. 7 The Speed-Clean can be coupled to the tractor by means of the 3-point linkage. The method is as follows: (Fig. 7) Remove the 3-point pins (1) and (2). -
Page 11: Working Depth Adjustment Of Brush
The procedure is as follows: (see fig.8) !! Make sure the Speed-Clean is blocked properly and cannot move on its own !! !! Turn off the tractor before dismounting !! 1. Turn Knob (1) clockwise to raise the brush 2. -
Page 12: Adjustabel Rake / Rear Brush
ADJUSTABEL RAKE / REAR BRUSH The machine is equipped with an adjustable rake section and a loose rear brush. (Fig 9) The rake can be set to different depths or in the transport position. Remove pin (3) and set the rake to the desired depth. Put pin (3) into the desired hole. Fig. -
Page 13: Transport Of The Speed-Clean
THE DRIVING SPEED The driving speed of the Speed-Clean is 12 km/h (7.4mph), but in practice the maximum speed must be read from the surface to be worked and the desired cleaning. THE USE OF THE SPEED-CLEAN Before the Speed-Clean can be used at a location the following must be checked: Are there any loose objects present on the field? First remove these. -
Page 14: Emptying Of The Dirt Receiving Bin
(See Fig.10) 1. Drive the Speed-Clean to the dumping site for collected waste. !! Make sure the Speed-Clean is blocked properly and cannot move on its own accord !! Switch off the tractor before continuing !! 2. Open the rotating lock (1) 3. -
Page 15: Problem Analysis
11.0 PROBLEM ANALYSIS Problem Possible Cause Solution Overspill material to be Working depth is adjusted Adjust the machine les deep. cleaned is caught in the dirt too deep. receiving bin. Vibration sieve is blocked. Open the vibration sieve. Work environment is too Wait till the work environment wet. -
Page 16: Maintenance
12.0 MAINTENANCE Time-line Check point /Lubrication Method point Before every use. Check for loose bolts / nuts. Tighten the loose bolts/nuts with the right torque. Presence and Legibility of Replace these if not safety stickers. (Fig. 5) present/damaged. After first 20 working hours Check the roller bearings If necessary replace these (new or repaired). -
Page 17: Adjustable Guard Plate Adjustment
12.1 ADJUSTABLE GUARD PLATE ADJUSTMENT Fig. 11 The machine is equipped with an adjustable guard plate. The plate is mounted above the brush. This can adjust the material flow of the brush. The adjusting the guard plate goes as follows (see fig. -
Page 18: Changing Of The Vibration Sieve
Changing the vibration sieve is done as follows (See Fig. 11) !! Make sure the Speed-Clean is blocked properly and cannot move on its own !! 1. Take the vibration sieve/dirt receiving bin from the machine as described in chapter 10.0 2. -
Page 19: Grease Points
12.3 GREASE POINTS Fig. 13 Grease points left & right. -
Page 20: Option: Magnetic Broom
This magnetic broom can be continuously variable adjusted in height. You can order this option under number: 247.100.002 Speed-Clean 1000 247.167.010 Speed-Clean 1700 See the parts manual for mounting this option on the Speed-Clean.
Need help?
Do you have a question about the Speed-Clean and is the answer not in the manual?
Questions and answers